Probe #bfc5f1a917 of ASRock N68-GS4 FX R2.0 Desktop Computer

Log: smartctl

/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD3200BPVT-80ZEST0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320 072 933 376 bytes [320 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Feb 14 07:51:34 2018 +04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7560) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 91) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 198 196 051 - 21780 3 Spin_Up_Time POS--K 152 125 021 - 1383 4 Start_Stop_Count -O--CK 001 001 000 - 229816 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 056 056 000 - 32515 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 092 092 000 - 8273 191 G-Sense_Error_Rate -O--CK 001 001 000 - 12903 192 Power-Off_Retract_Count -O--CK 199 199 000 - 1067 193 Load_Cycle_Count -O--CK 001 001 000 - 4102182 194 Temperature_Celsius -O---K 102 091 000 - 41 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 26 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 21795 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 21795 [2] occurred at disk power-on lifetime: 31674 hours (1319 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1a 97 cb e8 40 00 Error: UNC 8 sectors at LBA = 0x1a97cbe8 = 446155752 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:23:05.495 READ DMA EXT 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:23:02.679 READ DMA EXT 25 00 00 00 80 00 00 05 09 0b 58 40 00 00:23:02.667 READ DMA EXT 25 00 00 00 20 00 00 02 83 a6 40 40 00 00:23:02.655 READ DMA EXT 35 00 00 00 38 00 00 00 72 2b e8 40 00 00:23:02.654 WRITE DMA EXT Error 21794 [1] occurred at disk power-on lifetime: 31674 hours (1319 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1a 97 cb e8 40 00 Error: UNC 8 sectors at LBA = 0x1a97cbe8 = 446155752 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:23:02.679 READ DMA EXT 25 00 00 00 80 00 00 05 09 0b 58 40 00 00:23:02.667 READ DMA EXT 25 00 00 00 20 00 00 02 83 a6 40 40 00 00:23:02.655 READ DMA EXT 35 00 00 00 38 00 00 00 72 2b e8 40 00 00:23:02.654 WRITE DMA EXT 25 00 00 00 10 00 00 00 63 a2 b0 40 00 00:23:02.646 READ DMA EXT Error 21793 [0] occurred at disk power-on lifetime: 31674 hours (1319 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1a 97 cb e8 40 00 Error: UNC 8 sectors at LBA = 0x1a97cbe8 = 446155752 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:22:59.791 READ DMA EXT 25 00 00 00 78 00 00 05 09 0a e0 40 00 00:22:59.773 READ DMA EXT 25 00 00 00 48 00 00 03 63 7a 78 40 00 00:22:59.764 READ DMA EXT 25 00 00 00 20 00 00 00 5f 67 30 40 00 00:22:59.741 READ DMA EXT 25 00 00 00 08 00 00 00 56 b8 c8 40 00 00:22:59.740 READ DMA EXT Error 21792 [23] occurred at disk power-on lifetime: 31674 hours (1319 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1a 97 cb e8 40 00 Error: UNC 8 sectors at LBA = 0x1a97cbe8 = 446155752 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:22:56.720 READ DMA EXT 35 00 00 00 10 00 00 00 72 2b a8 40 00 00:22:56.720 WRITE DMA EXT 35 00 00 00 18 00 00 00 72 2b 88 40 00 00:22:56.719 WRITE DMA EXT 25 00 00 00 08 00 00 1a 97 cb e0 40 00 00:22:56.719 READ DMA EXT 35 00 00 00 10 00 00 00 72 2b 70 40 00 00:22:56.719 WRITE DMA EXT Error 21791 [22] occurred at disk power-on lifetime: 31674 hours (1319 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 1a 97 cb e8 40 00 Error: UNC 256 sectors at LBA = 0x1a97cbe8 = 446155752 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 1a 97 cb c8 40 00 00:22:53.817 READ DMA EXT 25 00 00 01 00 00 00 1a 97 ca c8 40 00 00:22:53.815 READ DMA EXT 25 00 00 01 00 00 00 1a 97 c9 c8 40 00 00:22:53.812 READ DMA EXT 25 00 00 01 00 00 00 1a 97 c8 c8 40 00 00:22:53.809 READ DMA EXT 25 00 00 01 00 00 00 1a 97 c7 c8 40 00 00:22:53.805 READ DMA EXT Error 21790 [21] occurred at disk power-on lifetime: 31674 hours (1319 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1a 97 cb e8 40 00 Error: UNC 8 sectors at LBA = 0x1a97cbe8 = 446155752 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:20:51.717 READ DMA EXT 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:20:48.920 READ DMA EXT 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:20:46.134 READ DMA EXT 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:20:43.322 READ DMA EXT ea 00 00 00 00 00 00 00 00 00 00 40 00 00:20:43.273 FLUSH CACHE EXT Error 21789 [20] occurred at disk power-on lifetime: 31674 hours (1319 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1a 97 cb e8 40 00 Error: UNC 8 sectors at LBA = 0x1a97cbe8 = 446155752 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:20:48.920 READ DMA EXT 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:20:46.134 READ DMA EXT 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:20:43.322 READ DMA EXT ea 00 00 00 00 00 00 00 00 00 00 40 00 00:20:43.273 FLUSH CACHE EXT 35 00 00 00 08 00 00 0f 2e f2 20 40 00 00:20:43.273 WRITE DMA EXT Error 21788 [19] occurred at disk power-on lifetime: 31674 hours (1319 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1a 97 cb e8 40 00 Error: UNC 8 sectors at LBA = 0x1a97cbe8 = 446155752 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:20:46.134 READ DMA EXT 25 00 00 00 08 00 00 1a 97 cb e8 40 00 00:20:43.322 READ DMA EXT ea 00 00 00 00 00 00 00 00 00 00 40 00 00:20:43.273 FLUSH CACHE EXT 35 00 00 00 08 00 00 0f 2e f2 20 40 00 00:20:43.273 WRITE DMA EXT 35 00 00 00 08 00 00 0f 2e f2 b0 40 00 00:20:43.273 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 40/42 Celsius Lifetime Min/Max Temperature: 37/53 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (2) Index Estimated Time Temperature Celsius 3 2018-02-14 05:44 41 ********************** ... ..( 8 skipped). .. ********************** 12 2018-02-14 05:53 41 ********************** 13 2018-02-14 05:54 40 ********************* ... ..( 15 skipped). .. ********************* 29 2018-02-14 06:10 40 ********************* 30 2018-02-14 06:11 41 ********************** ... ..( 5 skipped). .. ********************** 36 2018-02-14 06:17 41 ********************** 37 2018-02-14 06:18 ? - 38 2018-02-14 06:19 41 ********************** 39 2018-02-14 06:20 40 ********************* ... ..( 7 skipped). .. ********************* 47 2018-02-14 06:28 40 ********************* 48 2018-02-14 06:29 39 ******************** ... ..( 7 skipped). .. ******************** 56 2018-02-14 06:37 39 ******************** 57 2018-02-14 06:38 40 ********************* 58 2018-02-14 06:39 40 ********************* 59 2018-02-14 06:40 41 ********************** ... ..( 2 skipped). .. ********************** 62 2018-02-14 06:43 41 ********************** 63 2018-02-14 06:44 ? - 64 2018-02-14 06:45 41 ********************** 65 2018-02-14 06:46 41 ********************** 66 2018-02-14 06:47 41 ********************** 67 2018-02-14 06:48 ? - 68 2018-02-14 06:49 41 ********************** 69 2018-02-14 06:50 41 ********************** 70 2018-02-14 06:51 41 ********************** 71 2018-02-14 06:52 ? - 72 2018-02-14 06:53 38 ******************* 73 2018-02-14 06:54 ? - 74 2018-02-14 06:55 38 ******************* 75 2018-02-14 06:56 ? - 76 2018-02-14 06:57 37 ****************** 77 2018-02-14 06:58 ? - 78 2018-02-14 06:59 37 ****************** 79 2018-02-14 07:00 ? - 80 2018-02-14 07:01 37 ****************** 81 2018-02-14 07:02 ? - 82 2018-02-14 07:03 37 ****************** 83 2018-02-14 07:04 37 ****************** 84 2018-02-14 07:05 37 ****************** 85 2018-02-14 07:06 ? - 86 2018-02-14 07:07 38 ******************* 87 2018-02-14 07:08 38 ******************* 88 2018-02-14 07:09 ? - 89 2018-02-14 07:10 38 ******************* 90 2018-02-14 07:11 38 ******************* 91 2018-02-14 07:12 ? - 92 2018-02-14 07:13 38 ******************* 93 2018-02-14 07:14 38 ******************* 94 2018-02-14 07:15 ? - 95 2018-02-14 07:16 38 ******************* 96 2018-02-14 07:17 39 ******************** 97 2018-02-14 07:18 40 ********************* ... ..( 2 skipped). .. ********************* 100 2018-02-14 07:21 40 ********************* 101 2018-02-14 07:22 41 ********************** 102 2018-02-14 07:23 42 *********************** 103 2018-02-14 07:24 42 *********************** 104 2018-02-14 07:25 ? - 105 2018-02-14 07:26 41 ********************** 106 2018-02-14 07:27 ? - 107 2018-02-14 07:28 41 ********************** 108 2018-02-14 07:29 ? - 109 2018-02-14 07:30 41 ********************** 110 2018-02-14 07:31 40 ********************* 111 2018-02-14 07:32 ? - 112 2018-02-14 07:33 41 ********************** ... ..( 4 skipped). .. ********************** 117 2018-02-14 07:38 41 ********************** 118 2018-02-14 07:39 42 *********************** ... ..( 4 skipped). .. *********************** 123 2018-02-14 07:44 42 *********************** 124 2018-02-14 07:45 41 ********************** 125 2018-02-14 07:46 41 ********************** 126 2018-02-14 07:47 42 *********************** 127 2018-02-14 07:48 41 ********************** 0 2018-02-14 07:49 ? - 1 2018-02-14 07:50 41 ********************** 2 2018-02-14 07:51 41 ********************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 1205 Vendor specific


Hardware for Linux and BSD

GitHub