/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.19.0-2-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD10JPCX-24UE4T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: Not in smartctl database 7.3/5319 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Oct 18 03:43:53 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (17760) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 199) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 196 051 - 7809 3 Spin_Up_Time POS--K 179 177 021 - 2033 4 Start_Stop_Count -O--CK 081 081 000 - 19341 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 091 091 000 - 6785 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 083 083 000 - 17267 192 Power-Off_Retract_Count -O--CK 200 200 000 - 153 193 Load_Cycle_Count -O--CK 185 185 000 - 46533 194 Temperature_Celsius -O---K 124 099 000 - 23 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 199 000 - 101 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 240 Head_Flying_Hours -O--CK 092 092 000 - 6545 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 5150 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5150 [13] occurred at disk power-on lifetime: 3552 hours (148 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 12 3b 07 e8 40 00 Error: UNC at LBA = 0x123b07e8 = 305858536 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 c0 00 00 12 3b 07 e0 40 08 01:48:08.324 READ FPDMA QUEUED 60 00 20 00 b8 00 00 12 29 21 60 40 08 01:48:08.324 READ FPDMA QUEUED 60 00 20 00 b0 00 00 12 29 21 20 40 08 01:48:08.324 READ FPDMA QUEUED 60 00 18 00 a8 00 00 12 0a 16 28 40 08 01:48:08.321 READ FPDMA QUEUED 60 00 20 00 a0 00 00 12 0a 16 00 40 08 01:48:08.321 READ FPDMA QUEUED Error 5149 [12] occurred at disk power-on lifetime: 390 hours (16 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 1d 00 00 00 02 5f 02 e0 00 Error: UNC 29 sectors at LBA = 0x00025f02 = 155394 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:15:21.931 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:15:21.730 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:15:21.666 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:15:21.607 READ DMA EXT 25 00 00 00 22 00 00 00 02 5e de e0 00 00:15:21.607 READ DMA EXT Error 5148 [11] occurred at disk power-on lifetime: 390 hours (16 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 1d 00 00 00 02 5f 02 e0 00 Error: UNC 29 sectors at LBA = 0x00025f02 = 155394 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:15:21.730 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:15:21.666 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:15:21.607 READ DMA EXT 25 00 00 00 22 00 00 00 02 5e de e0 00 00:15:21.607 READ DMA EXT 25 00 00 00 1e 00 00 00 02 5e c0 e0 00 00:15:21.606 READ DMA EXT Error 5147 [10] occurred at disk power-on lifetime: 390 hours (16 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 1d 00 00 00 02 5f 02 e0 00 Error: UNC 29 sectors at LBA = 0x00025f02 = 155394 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:15:21.666 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:15:21.607 READ DMA EXT 25 00 00 00 22 00 00 00 02 5e de e0 00 00:15:21.607 READ DMA EXT 25 00 00 00 1e 00 00 00 02 5e c0 e0 00 00:15:21.606 READ DMA EXT 25 00 00 00 21 00 00 00 02 5e 9f e0 00 00:15:21.605 READ DMA EXT Error 5146 [9] occurred at disk power-on lifetime: 390 hours (16 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 1d 00 00 00 02 5f 02 e0 00 Error: UNC 29 sectors at LBA = 0x00025f02 = 155394 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:15:21.607 READ DMA EXT 25 00 00 00 22 00 00 00 02 5e de e0 00 00:15:21.607 READ DMA EXT 25 00 00 00 1e 00 00 00 02 5e c0 e0 00 00:15:21.606 READ DMA EXT 25 00 00 00 21 00 00 00 02 5e 9f e0 00 00:15:21.605 READ DMA EXT 25 00 00 00 1f 00 00 00 02 5e 80 e0 00 00:15:21.598 READ DMA EXT Error 5145 [8] occurred at disk power-on lifetime: 390 hours (16 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 1d 00 00 00 02 5f 02 e0 00 Error: UNC 29 sectors at LBA = 0x00025f02 = 155394 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:00:16.578 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:00:16.435 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:00:16.258 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:00:16.243 READ DMA EXT 25 00 00 00 22 00 00 00 02 5e de e0 00 00:00:16.243 READ DMA EXT Error 5144 [7] occurred at disk power-on lifetime: 390 hours (16 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 1d 00 00 00 02 5f 02 e0 00 Error: UNC 29 sectors at LBA = 0x00025f02 = 155394 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:00:16.435 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:00:16.258 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:00:16.243 READ DMA EXT 25 00 00 00 22 00 00 00 02 5e de e0 00 00:00:16.243 READ DMA EXT 25 00 00 00 1e 00 00 00 02 5e c0 e0 00 00:00:16.242 READ DMA EXT Error 5143 [6] occurred at disk power-on lifetime: 390 hours (16 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 1d 00 00 00 02 5f 02 e0 00 Error: UNC 29 sectors at LBA = 0x00025f02 = 155394 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:00:16.258 READ DMA EXT 25 00 00 00 1d 00 00 00 02 5f 00 e0 00 00:00:16.243 READ DMA EXT 25 00 00 00 22 00 00 00 02 5e de e0 00 00:00:16.243 READ DMA EXT 25 00 00 00 1e 00 00 00 02 5e c0 e0 00 00:00:16.242 READ DMA EXT 25 00 00 00 21 00 00 00 02 5e 9f e0 00 00:00:16.242 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Vendor (0x50) Completed without error 00% 368 - # 2 Short offline Completed: read failure 60% 368 98120 # 3 Vendor (0x50) Completed without error 00% 329 - # 4 Short offline Completed without error 00% 329 - # 5 Vendor (0x50) Aborted by host 70% 178 - # 6 Short offline Completed without error 00% 178 - # 7 Vendor (0x50) Completed without error 00% 125 - # 8 Short offline Completed: read failure 30% 125 98128 # 9 Vendor (0x50) Completed without error 00% 26 - #10 Short offline Completed without error 00% 26 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 23 Celsius Power Cycle Min/Max Temperature: 21/23 Celsius Lifetime Min/Max Temperature: 15/48 Celsius Specified Max Operating Temperature: 29 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (14) Index Estimated Time Temperature Celsius 15 2022-10-18 01:36 35 **************** ... ..( 3 skipped). .. **************** 19 2022-10-18 01:40 35 **************** 20 2022-10-18 01:41 36 ***************** ... ..( 2 skipped). .. ***************** 23 2022-10-18 01:44 36 ***************** 24 2022-10-18 01:45 37 ****************** ... ..( 3 skipped). .. ****************** 28 2022-10-18 01:49 37 ****************** 29 2022-10-18 01:50 36 ***************** ... ..( 6 skipped). .. ***************** 36 2022-10-18 01:57 36 ***************** 37 2022-10-18 01:58 35 **************** ... ..( 8 skipped). .. **************** 46 2022-10-18 02:07 35 **************** 47 2022-10-18 02:08 34 *************** ... ..( 30 skipped). .. *************** 78 2022-10-18 02:39 34 *************** 79 2022-10-18 02:40 33 ************** ... ..( 9 skipped). .. ************** 89 2022-10-18 02:50 33 ************** 90 2022-10-18 02:51 32 ************* ... ..( 13 skipped). .. ************* 104 2022-10-18 03:05 32 ************* 105 2022-10-18 03:06 33 ************** ... ..( 3 skipped). .. ************** 109 2022-10-18 03:10 33 ************** 110 2022-10-18 03:11 32 ************* ... ..( 26 skipped). .. ************* 9 2022-10-18 03:38 32 ************* 10 2022-10-18 03:39 ? - 11 2022-10-18 03:40 21 ** 12 2022-10-18 03:41 21 ** 13 2022-10-18 03:42 22 *** 14 2022-10-18 03:43 23 **** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2405 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 223 Vendor specific