/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.74-generic-2rosa2021.1-x86_64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K500 Device Model: HGST HTS545050A7E380 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GG2OACA0 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed May 4 04:50:51 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 112) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 071 062 - 0 2 Throughput_Performance P-S--K 198 100 040 - 126 3 Spin_Up_Time PO---K 252 100 033 - 1 4 Start_Stop_Count -O--CK 096 096 000 - 6934 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 384 (0 46) 7 Seek_Error_Rate POSR-K 100 100 067 - 0 8 Seek_Time_Performance P-S--K 112 100 040 - 35 9 Power_On_Hours -O--CK 043 043 000 - 25130 10 Spin_Retry_Count PO--CK 100 100 060 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 6780 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 091 000 - 51007040389531 188 Command_Timeout -O--CK 100 100 000 - 73016213507 190 Airflow_Temperature_Cel -O---K 064 041 045 Past 36 (Min/Max 35/36) 191 G-Sense_Error_Rate -O--CK 096 096 000 - 1253 192 Power-Off_Retract_Count -O--CK 100 100 000 - 12779715 193 Load_Cycle_Count -O--CK 001 001 000 - 1227731 196 Reallocated_Event_Count -O--CK 100 100 000 - 46 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0 223 Load_Retry_Count -O-R-K 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 411 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 411 [2] occurred at disk power-on lifetime: 24028 hours (1001 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 10 5e c3 2f 00 00 Error: UNC at LBA = 0x105ec32f = 274645807 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 38 00 00 10 5e c3 2f 40 00 03:40:25.365 READ FPDMA QUEUED 60 00 16 00 30 00 00 00 1b 7a 42 40 00 03:40:25.365 READ FPDMA QUEUED 60 00 80 00 28 00 00 23 ed 55 f0 40 00 03:40:25.360 READ FPDMA QUEUED 60 01 00 00 20 00 00 00 15 1e 30 40 00 03:40:25.345 READ FPDMA QUEUED 60 01 00 00 18 00 00 00 15 1d 30 40 00 03:40:25.345 READ FPDMA QUEUED Error 410 [1] occurred at disk power-on lifetime: 24028 hours (1001 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 10 5e c3 2e 00 00 Error: UNC at LBA = 0x105ec32e = 274645806 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 1f 00 a0 00 00 00 17 9a e6 40 00 03:40:21.836 READ FPDMA QUEUED 61 00 08 00 98 00 00 00 6f 57 90 40 00 03:40:21.835 WRITE FPDMA QUEUED 61 00 10 00 90 00 00 00 6b 4c 18 40 00 03:40:21.835 WRITE FPDMA QUEUED 60 00 08 00 88 00 00 1c 1b 08 a8 40 00 03:40:21.835 READ FPDMA QUEUED 61 00 10 00 80 00 00 00 6f 57 70 40 00 03:40:21.835 WRITE FPDMA QUEUED Error 409 [0] occurred at disk power-on lifetime: 24028 hours (1001 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 10 5e c3 2d 00 00 Error: UNC at LBA = 0x105ec32d = 274645805 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 68 00 00 10 5e c3 2d 40 00 03:40:18.458 READ FPDMA QUEUED 60 00 80 00 60 00 00 23 ea f6 58 40 00 03:40:18.448 READ FPDMA QUEUED 60 00 80 00 f8 00 00 23 ec d1 b8 40 00 03:40:18.351 READ FPDMA QUEUED 60 00 80 00 f0 00 00 23 e7 7f f8 40 00 03:40:18.351 READ FPDMA QUEUED 60 00 80 00 c0 00 00 1f fc aa 50 40 00 03:40:18.351 READ FPDMA QUEUED Error 408 [3] occurred at disk power-on lifetime: 24028 hours (1001 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 01 00 00 10 5e c3 2c 00 00 Error: UNC at LBA = 0x105ec32c = 274645804 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 28 00 00 04 b1 c7 92 40 00 03:40:14.929 READ FPDMA QUEUED 60 00 20 00 20 00 00 00 1e 73 08 40 00 03:40:14.929 READ FPDMA QUEUED 61 00 08 00 18 00 00 00 6f 57 38 40 00 03:40:14.929 WRITE FPDMA QUEUED 61 00 08 00 10 00 00 00 6b 4c 98 40 00 03:40:14.929 WRITE FPDMA QUEUED 60 00 01 00 08 00 00 10 5e c3 2c 40 00 03:40:14.928 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 24896 - # 2 Extended offline Completed without error 00% 24740 - # 3 Extended offline Completed without error 00% 24608 - # 4 Extended offline Completed without error 00% 24458 - # 5 Extended offline Completed without error 00% 24301 - # 6 Extended offline Completed: read failure 90% 24054 274645807 1 of 1 failed self-tests are outdated by newer successful extended offline self-test # 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 35/36 Celsius Lifetime Min/Max Temperature: 9/59 Celsius Specified Max Operating Temperature: 36 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (35) Index Estimated Time Temperature Celsius 36 2022-05-04 02:43 31 ************ ... ..( 18 skipped). .. ************ 55 2022-05-04 03:02 31 ************ 56 2022-05-04 03:03 30 *********** 57 2022-05-04 03:04 30 *********** 58 2022-05-04 03:05 31 ************ 59 2022-05-04 03:06 30 *********** 60 2022-05-04 03:07 31 ************ 61 2022-05-04 03:08 30 *********** 62 2022-05-04 03:09 30 *********** 63 2022-05-04 03:10 31 ************ 64 2022-05-04 03:11 31 ************ 65 2022-05-04 03:12 30 *********** 66 2022-05-04 03:13 30 *********** 67 2022-05-04 03:14 30 *********** 68 2022-05-04 03:15 31 ************ 69 2022-05-04 03:16 30 *********** ... ..( 6 skipped). .. *********** 76 2022-05-04 03:23 30 *********** 77 2022-05-04 03:24 31 ************ 78 2022-05-04 03:25 30 *********** ... ..( 4 skipped). .. *********** 83 2022-05-04 03:30 30 *********** 84 2022-05-04 03:31 31 ************ 85 2022-05-04 03:32 30 *********** ... ..( 6 skipped). .. *********** 92 2022-05-04 03:39 30 *********** 93 2022-05-04 03:40 31 ************ 94 2022-05-04 03:41 30 *********** 95 2022-05-04 03:42 31 ************ 96 2022-05-04 03:43 30 *********** ... ..( 4 skipped). .. *********** 101 2022-05-04 03:48 30 *********** 102 2022-05-04 03:49 ? - 103 2022-05-04 03:50 ? - 104 2022-05-04 03:51 31 ************ 105 2022-05-04 03:52 32 ************* 106 2022-05-04 03:53 33 ************** ... ..( 3 skipped). .. ************** 110 2022-05-04 03:57 33 ************** 111 2022-05-04 03:58 ? - 112 2022-05-04 03:59 33 ************** 113 2022-05-04 04:00 34 *************** ... ..( 2 skipped). .. *************** 116 2022-05-04 04:03 34 *************** 117 2022-05-04 04:04 ? - 118 2022-05-04 04:05 34 *************** 119 2022-05-04 04:06 35 **************** 120 2022-05-04 04:07 35 **************** 121 2022-05-04 04:08 35 **************** 122 2022-05-04 04:09 36 ***************** ... ..( 2 skipped). .. ***************** 125 2022-05-04 04:12 36 ***************** 126 2022-05-04 04:13 37 ****************** ... ..( 2 skipped). .. ****************** 1 2022-05-04 04:16 37 ****************** 2 2022-05-04 04:17 ? - 3 2022-05-04 04:18 36 ***************** 4 2022-05-04 04:19 36 ***************** 5 2022-05-04 04:20 36 ***************** 6 2022-05-04 04:21 ? - ... ..( 2 skipped). .. - 9 2022-05-04 04:24 ? - 10 2022-05-04 04:25 35 **************** ... ..( 3 skipped). .. **************** 14 2022-05-04 04:29 35 **************** 15 2022-05-04 04:30 ? - 16 2022-05-04 04:31 ? - 17 2022-05-04 04:32 33 ************** 18 2022-05-04 04:33 34 *************** 19 2022-05-04 04:34 34 *************** 20 2022-05-04 04:35 35 **************** 21 2022-05-04 04:36 34 *************** 22 2022-05-04 04:37 35 **************** 23 2022-05-04 04:38 ? - 24 2022-05-04 04:39 35 **************** 25 2022-05-04 04:40 36 ***************** ... ..( 2 skipped). .. ***************** 28 2022-05-04 04:43 36 ***************** 29 2022-05-04 04:44 35 **************** ... ..( 2 skipped). .. **************** 32 2022-05-04 04:47 35 **************** 33 2022-05-04 04:48 ? - 34 2022-05-04 04:49 35 **************** 35 2022-05-04 04:50 36 ***************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 373 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS