/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.53-1-pve] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba P300 Device Model: TOSHIBA HDWD120 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MX4OACF0 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Nov 26 10:16:52 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (14631) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 244) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 139 139 054 - 70 3 Spin_Up_Time POS--- 147 147 024 - 277 (Average 238) 4 Start_Stop_Count -O--C- 100 100 000 - 43 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 124 124 020 - 33 9 Power_On_Hours -O--C- 096 096 000 - 33197 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 32 192 Power-Off_Retract_Count -O--CK 100 100 000 - 48 193 Load_Cycle_Count -O--C- 100 100 000 - 48 194 Temperature_Celsius -O---- 206 206 000 - 29 (Min/Max 19/37) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 22/34 Celsius Lifetime Min/Max Temperature: 19/37 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (50) Index Estimated Time Temperature Celsius 51 2023-11-26 08:09 29 ********** ... ..(126 skipped). .. ********** 50 2023-11-26 10:16 29 ********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 32 --- Lifetime Power-On Resets 0x01 0x010 4 33197 --- Power-on Hours 0x01 0x018 6 72035834350 --- Logical Sectors Written 0x01 0x020 6 1837488193 --- Number of Write Commands 0x01 0x028 6 55817163031 --- Logical Sectors Read 0x01 0x030 6 592207409 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 33193 --- Spindle Motor Power-on Hours 0x03 0x010 4 33193 --- Head Flying Hours 0x03 0x018 4 48 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 1 --- Read Recovery Attempts 0x03 0x030 4 6 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 14 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 29 --- Current Temperature 0x05 0x010 1 29 N-- Average Short Term Temperature 0x05 0x018 1 30 N-- Average Long Term Temperature 0x05 0x020 1 37 --- Highest Temperature 0x05 0x028 1 19 --- Lowest Temperature 0x05 0x030 1 33 N-- Highest Average Short Term Temperature 0x05 0x038 1 22 N-- Lowest Average Short Term Temperature 0x05 0x040 1 32 N-- Highest Average Long Term Temperature 0x05 0x048 1 23 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 247 --- Number of Hardware Resets 0x06 0x010 4 206 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.53-1-pve] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba P300 Device Model: TOSHIBA HDWD120 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MX4OACF0 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Nov 26 10:16:54 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (14344) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 239) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 139 139 054 - 71 3 Spin_Up_Time POS--- 131 131 024 - 280 (Average 296) 4 Start_Stop_Count -O--C- 099 099 000 - 4100 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 124 124 020 - 33 9 Power_On_Hours -O--C- 096 096 000 - 33191 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 32 192 Power-Off_Retract_Count -O--CK 097 097 000 - 4265 193 Load_Cycle_Count -O--C- 097 097 000 - 4265 194 Temperature_Celsius -O---- 206 206 000 - 29 (Min/Max 16/37) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 6 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 6 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [1] occurred at disk power-on lifetime: 19085 hours (795 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 a0 00 00 12 70 27 70 02 00 Error: ICRC, ABRT at LBA = 0x12702770 = 309340016 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 03 c0 00 40 00 00 12 70 24 50 40 00 1d+16:55:02.651 WRITE FPDMA QUEUED 61 00 08 00 38 00 00 12 df a7 70 40 00 1d+16:55:02.651 WRITE FPDMA QUEUED 61 03 18 00 e0 00 00 12 70 21 38 40 00 1d+16:55:02.650 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+16:55:02.599 FLUSH CACHE EXT 61 00 58 00 20 00 00 12 70 20 e0 40 00 1d+16:55:02.599 WRITE FPDMA QUEUED Error 5 [0] occurred at disk power-on lifetime: 19057 hours (794 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 12 ca 4f 00 00 Error: ICRC, ABRT at LBA = 0x0012ca4f = 1231439 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 18 00 70 00 00 00 12 ca 38 40 00 12:49:21.818 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 12:49:21.810 FLUSH CACHE EXT 61 00 18 00 30 00 00 00 12 ca 20 40 00 12:49:21.810 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 12:49:21.801 FLUSH CACHE EXT 61 00 18 00 28 00 00 00 12 ca 08 40 00 12:49:21.801 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 18775 hours (782 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 44 0c c0 9f 04 00 Error: ICRC, ABRT at LBA = 0x440cc09f = 1141686431 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 b0 00 00 44 0c c0 98 40 00 1d+06:13:00.572 WRITE FPDMA QUEUED 61 00 08 00 30 00 00 44 0c c0 90 40 00 1d+06:13:00.572 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+06:13:00.564 FLUSH CACHE EXT 61 00 18 00 f0 00 00 00 7d 52 d8 40 00 1d+06:13:00.564 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+06:13:00.556 FLUSH CACHE EXT Error 3 [2] occurred at disk power-on lifetime: 18775 hours (782 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 20 00 00 00 7f b9 a8 00 00 Error: ICRC, ABRT at LBA = 0x007fb9a8 = 8370600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 50 00 78 00 00 00 7f b9 78 40 00 1d+05:49:11.029 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+05:49:11.021 FLUSH CACHE EXT 61 00 50 00 68 00 00 00 7f b9 20 40 00 1d+05:49:11.021 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 00 1d+05:49:11.014 FLUSH CACHE EXT 61 00 50 00 60 00 00 00 7f b8 c8 40 00 1d+05:49:11.014 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 22216 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 23/34 Celsius Lifetime Min/Max Temperature: 16/37 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (105) Index Estimated Time Temperature Celsius 106 2023-11-26 08:09 29 ********** ... ..(101 skipped). .. ********** 80 2023-11-26 09:51 29 ********** 81 2023-11-26 09:52 28 ********* 82 2023-11-26 09:53 29 ********** ... ..( 22 skipped). .. ********** 105 2023-11-26 10:16 29 ********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 32 --- Lifetime Power-On Resets 0x01 0x010 4 33191 --- Power-on Hours 0x01 0x018 6 43761328163 --- Logical Sectors Written 0x01 0x020 6 945190032 --- Number of Write Commands 0x01 0x028 6 41324033770 --- Logical Sectors Read 0x01 0x030 6 519559064 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 22967 --- Spindle Motor Power-on Hours 0x03 0x010 4 22966 --- Head Flying Hours 0x03 0x018 4 4265 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 6 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 12 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 29 --- Current Temperature 0x05 0x010 1 29 N-- Average Short Term Temperature 0x05 0x018 1 29 N-- Average Long Term Temperature 0x05 0x020 1 37 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 33 N-- Highest Average Short Term Temperature 0x05 0x038 1 18 N-- Lowest Average Short Term Temperature 0x05 0x040 1 32 N-- Highest Average Long Term Temperature 0x05 0x048 1 19 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 4299 --- Number of Hardware Resets 0x06 0x010 4 4268 --- Number of ASR Events 0x06 0x018 4 6 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.53-1-pve] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba P300 Device Model: TOSHIBA HDWD120 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MX4OACF0 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Nov 26 10:16:57 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13961) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 233) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 139 139 054 - 71 3 Spin_Up_Time POS--- 130 130 024 - 283 (Average 300) 4 Start_Stop_Count -O--C- 100 100 000 - 3163 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 124 124 020 - 33 9 Power_On_Hours -O--C- 096 096 000 - 33184 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 32 192 Power-Off_Retract_Count -O--CK 098 098 000 - 3258 193 Load_Cycle_Count -O--C- 098 098 000 - 3258 194 Temperature_Celsius -O---- 214 214 000 - 28 (Min/Max 16/36) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 19063 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 22/33 Celsius Lifetime Min/Max Temperature: 16/36 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (49) Index Estimated Time Temperature Celsius 50 2023-11-26 08:09 28 ********* ... ..(126 skipped). .. ********* 49 2023-11-26 10:16 28 ********* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 32 --- Lifetime Power-On Resets 0x01 0x010 4 33184 --- Power-on Hours 0x01 0x018 6 59804009136 --- Logical Sectors Written 0x01 0x020 6 1352890743 --- Number of Write Commands 0x01 0x028 6 48358866805 --- Logical Sectors Read 0x01 0x030 6 564572138 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 22426 --- Spindle Motor Power-on Hours 0x03 0x010 4 22426 --- Head Flying Hours 0x03 0x018 4 3258 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 6 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 11 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 29 --- Current Temperature 0x05 0x010 1 28 N-- Average Short Term Temperature 0x05 0x018 1 28 N-- Average Long Term Temperature 0x05 0x020 1 36 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 32 N-- Highest Average Short Term Temperature 0x05 0x038 1 17 N-- Lowest Average Short Term Temperature 0x05 0x040 1 31 N-- Highest Average Long Term Temperature 0x05 0x048 1 18 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 3348 --- Number of Hardware Resets 0x06 0x010 4 3317 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdd smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.53-1-pve] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba P300 Device Model: TOSHIBA HDWD120 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MX4OACF0 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Nov 26 10:16:59 2023 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (14248) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 238) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 140 140 054 - 67 3 Spin_Up_Time POS--- 130 130 024 - 281 (Average 300) 4 Start_Stop_Count -O--C- 100 100 000 - 3160 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 124 124 020 - 33 9 Power_On_Hours -O--C- 096 096 000 - 33183 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 32 192 Power-Off_Retract_Count -O--CK 098 098 000 - 3254 193 Load_Cycle_Count -O--C- 098 098 000 - 3254 194 Temperature_Celsius -O---- 206 206 000 - 29 (Min/Max 15/36) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 22/33 Celsius Lifetime Min/Max Temperature: 15/36 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (120) Index Estimated Time Temperature Celsius 121 2023-11-26 08:10 28 ********* ... ..( 4 skipped). .. ********* 126 2023-11-26 08:15 28 ********* 127 2023-11-26 08:16 29 ********** 0 2023-11-26 08:17 28 ********* ... ..( 2 skipped). .. ********* 3 2023-11-26 08:20 28 ********* 4 2023-11-26 08:21 29 ********** 5 2023-11-26 08:22 28 ********* ... ..( 8 skipped). .. ********* 14 2023-11-26 08:31 28 ********* 15 2023-11-26 08:32 29 ********** 16 2023-11-26 08:33 29 ********** 17 2023-11-26 08:34 29 ********** 18 2023-11-26 08:35 28 ********* 19 2023-11-26 08:36 28 ********* 20 2023-11-26 08:37 29 ********** 21 2023-11-26 08:38 29 ********** 22 2023-11-26 08:39 28 ********* 23 2023-11-26 08:40 29 ********** 24 2023-11-26 08:41 28 ********* 25 2023-11-26 08:42 29 ********** 26 2023-11-26 08:43 28 ********* 27 2023-11-26 08:44 29 ********** 28 2023-11-26 08:45 28 ********* 29 2023-11-26 08:46 29 ********** 30 2023-11-26 08:47 28 ********* 31 2023-11-26 08:48 29 ********** 32 2023-11-26 08:49 29 ********** 33 2023-11-26 08:50 29 ********** 34 2023-11-26 08:51 28 ********* ... ..( 3 skipped). .. ********* 38 2023-11-26 08:55 28 ********* 39 2023-11-26 08:56 29 ********** 40 2023-11-26 08:57 28 ********* 41 2023-11-26 08:58 29 ********** 42 2023-11-26 08:59 29 ********** 43 2023-11-26 09:00 28 ********* 44 2023-11-26 09:01 28 ********* 45 2023-11-26 09:02 29 ********** 46 2023-11-26 09:03 28 ********* 47 2023-11-26 09:04 28 ********* 48 2023-11-26 09:05 29 ********** 49 2023-11-26 09:06 28 ********* ... ..( 5 skipped). .. ********* 55 2023-11-26 09:12 28 ********* 56 2023-11-26 09:13 29 ********** 57 2023-11-26 09:14 28 ********* 58 2023-11-26 09:15 28 ********* 59 2023-11-26 09:16 29 ********** 60 2023-11-26 09:17 28 ********* ... ..( 2 skipped). .. ********* 63 2023-11-26 09:20 28 ********* 64 2023-11-26 09:21 29 ********** 65 2023-11-26 09:22 28 ********* ... ..( 54 skipped). .. ********* 120 2023-11-26 10:17 28 ********* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 32 --- Lifetime Power-On Resets 0x01 0x010 4 33183 --- Power-on Hours 0x01 0x018 6 58543223030 --- Logical Sectors Written 0x01 0x020 6 1336686009 --- Number of Write Commands 0x01 0x028 6 42419508442 --- Logical Sectors Read 0x01 0x030 6 511830681 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 22423 --- Spindle Motor Power-on Hours 0x03 0x010 4 22423 --- Head Flying Hours 0x03 0x018 4 3254 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 6 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 11 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 28 --- Current Temperature 0x05 0x010 1 28 N-- Average Short Term Temperature 0x05 0x018 1 29 N-- Average Long Term Temperature 0x05 0x020 1 36 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x030 1 32 N-- Highest Average Short Term Temperature 0x05 0x038 1 17 N-- Lowest Average Short Term Temperature 0x05 0x040 1 31 N-- Highest Average Long Term Temperature 0x05 0x048 1 18 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 3336 --- Number of Hardware Resets 0x06 0x010 4 3305 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS