/dev/sda === START OF INFORMATION SECTION === Model Family: HGST Travelstar Z5K1000 Device Model: HGST HTS541010A7E630 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: SE0OA4A0 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu May 10 20:57:09 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 1 (minimum power consumption with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 232) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 135 135 033 - 1 4 Start_Stop_Count -O--C- 045 045 000 - 87989 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 084 084 000 - 7419 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 2922 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 33 193 Load_Cycle_Count -O--C- 081 081 000 - 199907 194 Temperature_Celsius -O---- 187 187 000 - 32 (Min/Max 16/47) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 30/34 Celsius Lifetime Min/Max Temperature: 16/47 Celsius Lifetime Average Temperature: 33 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (23) Index Estimated Time Temperature Celsius 24 2018-05-10 18:50 33 ************** ... ..( 15 skipped). .. ************** 40 2018-05-10 19:06 33 ************** 41 2018-05-10 19:07 32 ************* ... ..( 3 skipped). .. ************* 45 2018-05-10 19:11 32 ************* 46 2018-05-10 19:12 31 ************ ... ..( 4 skipped). .. ************ 51 2018-05-10 19:17 31 ************ 52 2018-05-10 19:18 30 *********** ... ..( 2 skipped). .. *********** 55 2018-05-10 19:21 30 *********** 56 2018-05-10 19:22 31 ************ 57 2018-05-10 19:23 31 ************ 58 2018-05-10 19:24 30 *********** ... ..( 3 skipped). .. *********** 62 2018-05-10 19:28 30 *********** 63 2018-05-10 19:29 31 ************ ... ..( 2 skipped). .. ************ 66 2018-05-10 19:32 31 ************ 67 2018-05-10 19:33 32 ************* 68 2018-05-10 19:34 32 ************* 69 2018-05-10 19:35 33 ************** ... ..( 4 skipped). .. ************** 74 2018-05-10 19:40 33 ************** 75 2018-05-10 19:41 32 ************* ... ..( 6 skipped). .. ************* 82 2018-05-10 19:48 32 ************* 83 2018-05-10 19:49 31 ************ 84 2018-05-10 19:50 31 ************ 85 2018-05-10 19:51 32 ************* ... ..( 6 skipped). .. ************* 92 2018-05-10 19:58 32 ************* 93 2018-05-10 19:59 33 ************** 94 2018-05-10 20:00 33 ************** 95 2018-05-10 20:01 33 ************** 96 2018-05-10 20:02 34 *************** 97 2018-05-10 20:03 34 *************** 98 2018-05-10 20:04 34 *************** 99 2018-05-10 20:05 33 ************** 100 2018-05-10 20:06 33 ************** 101 2018-05-10 20:07 34 *************** ... ..( 3 skipped). .. *************** 105 2018-05-10 20:11 34 *************** 106 2018-05-10 20:12 33 ************** 107 2018-05-10 20:13 33 ************** 108 2018-05-10 20:14 32 ************* ... ..( 2 skipped). .. ************* 111 2018-05-10 20:17 32 ************* 112 2018-05-10 20:18 31 ************ ... ..( 16 skipped). .. ************ 1 2018-05-10 20:35 31 ************ 2 2018-05-10 20:36 32 ************* 3 2018-05-10 20:37 31 ************ 4 2018-05-10 20:38 31 ************ 5 2018-05-10 20:39 32 ************* ... ..( 17 skipped). .. ************* 23 2018-05-10 20:57 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 44371 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 27 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb === START OF INFORMATION SECTION === Device Model: KINGSTON SM2280S3G2120G Serial Number: -- Firmware Version: SAFM01.R User Capacity: 120 034 123 776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: M.2 Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu May 10 20:57:10 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x05) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 30) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 3) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--- 100 100 050 - 0 5 Reallocated_Sector_Ct PO--C- 100 100 050 - 0 7 Unknown_SSD_Attribute PO-R-- 100 100 050 - 0 8 Unknown_SSD_Attribute P-S--- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 6767 12 Power_Cycle_Count -O--C- 100 100 000 - 2421 168 Unknown_Attribute -O--C- 100 100 000 - 0 170 Unknown_Attribute PO---- 100 100 010 - 178 173 Unknown_Attribute -O--C- 100 100 000 - 6029470 175 Program_Fail_Count_Chip PO--C- 100 100 050 - 0 187 Reported_Uncorrect -O--C- 100 100 000 - 0 192 Power-Off_Retract_Count -O--C- 100 100 000 - 151 194 Temperature_Celsius PO---K 068 033 030 - 32 (Min/Max 17/67) 196 Reallocated_Event_Count -O---- 100 100 010 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count PO-R-- 100 100 050 - 0 218 Unknown_Attribute PO-R-- 100 100 050 - 0 231 Temperature_Celsius PO--C- 100 100 000 - 97 233 Media_Wearout_Indicator PO-R-- 100 100 000 - 3482 240 Unknown_SSD_Attribute PO--C- 100 100 000 - 0 241 Total_LBAs_Written -O--C- 100 100 000 - 9542 242 Total_LBAs_Read -O--C- 100 100 000 - 7242 244 Unknown_Attribute -O---- 100 100 000 - 92 245 Unknown_Attribute -O---- 100 100 000 - 158 246 Unknown_Attribute -O--C- 100 100 000 - 3117312 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 6 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 765 - # 2 Conveyance offline Completed without error 00% 764 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 2421 --- Lifetime Power-On Resets 0x01 0x018 6 20011037012 --- Logical Sectors Written 0x01 0x020 6 598788246 --- Number of Write Commands 0x01 0x028 6 15188845910 --- Logical Sectors Read 0x01 0x030 6 250003256 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 185048 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 2 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 32 --- Current Temperature 0x05 0x010 1 32 --- Average Short Term Temperature 0x05 0x018 1 32 --- Average Long Term Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 5 --- Lowest Temperature 0x05 0x030 1 50 --- Highest Average Short Term Temperature 0x05 0x038 1 16 --- Lowest Average Short Term Temperature 0x05 0x040 1 50 --- Highest Average Long Term Temperature 0x05 0x048 1 16 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 50 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 7252 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 5 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 82290656 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 9641 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC