/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.8.0-40-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ExcelStor Technology J8160S Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: P22OABEA User Capacity: 160,037,658,112 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA/ATAPI-7 T13/1532D revision 1 Local Time is: Tue Sep 24 21:06:48 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 128 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2865) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--- 124 124 024 - 160 (Average 161) 4 Start_Stop_Count -O--C- 099 099 000 - 5908 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 151 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 020 - 0 9 Power_On_Hours -O--C- 099 099 000 - 10966 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 5850 192 Power-Off_Retract_Count -O--CK 096 096 000 - 5932 193 Load_Cycle_Count -O--C- 096 096 000 - 5932 194 Temperature_Celsius -O---- 150 150 000 - 40 (Min/Max 14/65) 196 Reallocated_Event_Count -O--CK 100 100 000 - 151 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 253 000 - 1342 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 52 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 52 [2] occurred at disk power-on lifetime: 10867 hours (452 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 b7 5b 80 e2 00 Error: UNC 8 sectors at LBA = 0x02b75b80 = 45570944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 02 b7 5b 80 e0 00 00:20:57.000 READ DMA EXT 25 00 00 00 80 00 00 02 b7 5b 80 e0 00 00:20:52.200 READ DMA EXT 35 00 00 00 08 00 00 00 48 cb d8 e0 00 00:20:52.200 WRITE DMA EXT 25 00 00 00 0d 00 00 00 48 ca e9 e0 00 00:20:52.200 READ DMA EXT ea 00 00 00 00 52 3d c7 00 00 00 a0 00 00:20:52.100 FLUSH CACHE EXT Error 51 [1] occurred at disk power-on lifetime: 10867 hours (452 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 02 b7 5b 80 e2 00 Error: UNC 128 sectors at LBA = 0x02b75b80 = 45570944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 02 b7 5b 80 e0 00 00:20:52.200 READ DMA EXT 35 00 00 00 08 00 00 00 48 cb d8 e0 00 00:20:52.200 WRITE DMA EXT 25 00 00 00 0d 00 00 00 48 ca e9 e0 00 00:20:52.200 READ DMA EXT ea 00 00 00 00 52 3d c7 00 00 00 a0 00 00:20:52.100 FLUSH CACHE EXT 25 00 00 00 08 00 00 04 52 3d c0 e0 00 00:20:52.100 READ DMA EXT Error 50 [0] occurred at disk power-on lifetime: 10867 hours (452 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 c0 00 00 02 b7 5b 80 e2 00 Error: UNC 192 sectors at LBA = 0x02b75b80 = 45570944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 f8 00 00 02 b7 5b 48 e0 00 00:20:47.000 READ DMA EXT 25 00 00 00 08 00 00 02 b7 5b 40 e0 00 00:20:47.000 READ DMA EXT 25 00 00 00 40 00 00 02 48 1d 70 e0 00 00:20:47.000 READ DMA EXT 25 00 00 00 40 00 00 02 1b cd c0 e0 00 00:20:47.000 READ DMA EXT 25 00 00 00 30 00 00 01 d9 ef 42 e0 00 00:20:47.000 READ DMA EXT Error 49 [3] occurred at disk power-on lifetime: 10867 hours (452 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 c0 00 00 02 b7 5b 80 e2 00 Error: UNC 192 sectors at LBA = 0x02b75b80 = 45570944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 02 b7 5b 40 e0 00 00:20:41.900 READ DMA EXT 25 00 00 00 23 00 00 02 d3 00 38 e0 00 00:20:41.900 READ DMA EXT 25 00 00 01 00 00 00 02 b7 5a 40 e0 00 00:20:41.900 READ DMA EXT 25 00 00 00 08 00 00 02 d3 00 30 e0 00 00:20:41.900 READ DMA EXT 25 00 00 01 00 00 00 02 b7 59 40 e0 00 00:20:41.900 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: --/41 Celsius Lifetime Min/Max Temperature: --/65 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (24) Index Estimated Time Temperature Celsius 25 2024-09-24 18:59 39 ******************** ... ..( 50 skipped). .. ******************** 76 2024-09-24 19:50 39 ******************** 77 2024-09-24 19:51 ? - 78 2024-09-24 19:52 24 ***** 79 2024-09-24 19:53 26 ******* 80 2024-09-24 19:54 28 ********* 81 2024-09-24 19:55 30 *********** 82 2024-09-24 19:56 31 ************ 83 2024-09-24 19:57 31 ************ 84 2024-09-24 19:58 31 ************ 85 2024-09-24 19:59 32 ************* 86 2024-09-24 20:00 32 ************* 87 2024-09-24 20:01 33 ************** 88 2024-09-24 20:02 34 *************** ... ..( 2 skipped). .. *************** 91 2024-09-24 20:05 34 *************** 92 2024-09-24 20:06 35 **************** 93 2024-09-24 20:07 35 **************** 94 2024-09-24 20:08 35 **************** 95 2024-09-24 20:09 36 ***************** ... ..( 2 skipped). .. ***************** 98 2024-09-24 20:12 36 ***************** 99 2024-09-24 20:13 37 ****************** ... ..( 5 skipped). .. ****************** 105 2024-09-24 20:19 37 ****************** 106 2024-09-24 20:20 38 ******************* ... ..( 13 skipped). .. ******************* 120 2024-09-24 20:34 38 ******************* 121 2024-09-24 20:35 39 ******************** ... ..( 6 skipped). .. ******************** 0 2024-09-24 20:42 39 ******************** 1 2024-09-24 20:43 40 ********************* 2 2024-09-24 20:44 40 ********************* 3 2024-09-24 20:45 41 ********************** 4 2024-09-24 20:46 41 ********************** 5 2024-09-24 20:47 40 ********************* ... ..( 18 skipped). .. ********************* 24 2024-09-24 21:06 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS