/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.20-generic-2rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD1600AAJS-08PSA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 05.06H05 User Capacity: 160,040,803,840 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Tue Jun 27 13:18:53 2023 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4560) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 61) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 0 3 Spin_Up_Time PO---- 159 158 021 - 3016 4 Start_Stop_Count -O--CK 100 100 000 - 955 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 098 098 000 - 1862 10 Spin_Retry_Count -O--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 930 192 Power-Off_Retract_Count -O--CK 200 200 000 - 162 193 Load_Cycle_Count -O--CK 200 200 000 - 956 194 Temperature_Celsius -O---K 113 098 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 12 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 27 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 27 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 0e 25 4b f6 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 00 4b 05 00 f6 25 00 00 00 00:00:32.896 NOP [Abort queued commands] 01 fc 25 4b f5 00 08 00 41 00 00 00 00 01:22:58.173 [RESERVED] 00 80 00 00 00 4b fb 00 f5 25 00 00 00 00:00:32.896 NOP [Abort queued commands] Error 26 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 72 25 30 d8 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 00 30 72 00 d8 25 00 00 00 00:00:32.896 NOP [Abort queued commands] 00 71 25 30 d8 00 80 00 80 00 00 00 00 00:53:21.137 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 80 30 70 00 d8 25 00 00 00 00:00:00.128 NOP [Abort queued commands] Error 25 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 10 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 f5 42 0b 89 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 00 00 60 0b f5 01 89 42 00 00 00 00:00:28.688 NOP [Abort queued commands] 01 53 42 0b 82 00 20 00 a0 00 00 00 01 00:12:36.200 [RESERVED] 00 20 00 00 20 0b 21 01 82 42 00 00 00 00:00:32.800 NOP [Abort queued commands] Error 24 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 20 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 53 42 0b 82 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 00 00 20 0b 21 01 82 42 00 00 00 00:00:32.800 NOP [Abort queued commands] 01 9c 42 0b 70 00 20 00 00 00 00 00 01 00:12:32.143 [RESERVED] 00 20 00 00 40 0b 9c 01 70 42 00 00 00 00:00:24.608 NOP [Abort queued commands] Error 23 [22] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 20 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 0f 42 0b 7a 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 00 00 60 0b 9c 01 70 42 00 00 00 00:00:00.032 NOP [Abort queued commands] 01 0a 42 0b 69 00 20 00 40 00 00 00 01 00:12:29.724 [RESERVED] 00 40 00 00 40 0b 0a 01 69 42 00 00 00 00:00:32.832 NOP [Abort queued commands] Error 22 [21] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 20 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 9c 42 0b 70 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 00 00 40 0b 9c 01 70 42 00 00 00 00:00:24.608 NOP [Abort queued commands] 01 0a 42 0b 69 00 40 00 80 00 00 00 01 00:12:27.786 [RESERVED] 00 40 00 00 00 0b fd 01 60 42 00 00 00 00:00:16.448 NOP [Abort queued commands] Error 21 [20] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 40 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 0a 42 0b 69 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 40 00 00 40 0b 0a 01 69 42 00 00 00 00:00:32.832 NOP [Abort queued commands] 01 fd 42 0b 60 00 40 00 00 00 00 00 01 00:12:25.725 [RESERVED] 00 40 00 00 80 0b ca 01 60 42 00 00 00 00:00:49.216 NOP [Abort queued commands] Error 20 [19] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 40 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 fd 42 0b 60 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 40 00 00 c0 0b fd 01 60 42 00 00 00 00:00:00.064 NOP [Abort queued commands] 01 bd 42 0b 58 00 40 00 80 00 00 00 01 00:12:25.674 [RESERVED] 00 80 00 00 40 0b 29 01 51 42 00 00 00 00:00:16.448 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 1198 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 27/29 Celsius Lifetime Min/Max Temperature: 27/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (1) Index Estimated Time Temperature Celsius 2 2023-06-27 11:11 34 *************** 3 2023-06-27 11:12 34 *************** 4 2023-06-27 11:13 35 **************** ... ..( 46 skipped). .. **************** 51 2023-06-27 12:00 35 **************** 52 2023-06-27 12:01 34 *************** 53 2023-06-27 12:02 34 *************** 54 2023-06-27 12:03 35 **************** 55 2023-06-27 12:04 35 **************** 56 2023-06-27 12:05 35 **************** 57 2023-06-27 12:06 34 *************** 58 2023-06-27 12:07 35 **************** 59 2023-06-27 12:08 35 **************** 60 2023-06-27 12:09 34 *************** 61 2023-06-27 12:10 34 *************** 62 2023-06-27 12:11 35 **************** 63 2023-06-27 12:12 35 **************** 64 2023-06-27 12:13 35 **************** 65 2023-06-27 12:14 34 *************** ... ..( 5 skipped). .. *************** 71 2023-06-27 12:20 34 *************** 72 2023-06-27 12:21 35 **************** ... ..( 43 skipped). .. **************** 116 2023-06-27 13:05 35 **************** 117 2023-06-27 13:06 34 *************** 118 2023-06-27 13:07 ? - 119 2023-06-27 13:08 27 ******** 120 2023-06-27 13:09 27 ******** 121 2023-06-27 13:10 28 ********* 122 2023-06-27 13:11 28 ********* 123 2023-06-27 13:12 ? - 124 2023-06-27 13:13 27 ******** 125 2023-06-27 13:14 28 ********* 126 2023-06-27 13:15 28 ********* 127 2023-06-27 13:16 29 ********** 0 2023-06-27 13:17 29 ********** 1 2023-06-27 13:18 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x8000 4 334 Vendor specific /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.1.20-generic-2rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD2500AAJS-22VTA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01B01 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) Local Time is: Tue Jun 27 13:18:53 2023 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4980) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 61) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 005 051 Past 1352 3 Spin_Up_Time PO---- 177 176 021 - 2141 4 Start_Stop_Count -O--CK 100 100 000 - 7 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 000 - 0 9 Power_On_Hours -O--CK 098 098 000 - 1934 10 Spin_Retry_Count -O--C- 100 253 000 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1236 192 Power-Off_Retract_Count -O--CK 200 200 000 - 463 193 Load_Cycle_Count -O--CK 200 200 000 - 1236 194 Temperature_Celsius -O---K 113 098 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 199 000 - 0 198 Offline_Uncorrectable ----C- 100 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 1 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1662 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1662 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 f8 25 d9 2a 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 80 d9 f7 00 2a 25 00 00 00 00:00:00.128 NOP [Abort queued commands] 00 f6 25 d9 2a 00 80 00 00 00 00 00 00 03:57:12.310 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 00 d9 f5 00 2a 25 00 00 00 00:00:32.896 NOP [Abort queued commands] Error 1661 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 56 25 d9 1f 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 80 d9 55 00 1f 25 00 00 00 00:00:00.128 NOP [Abort queued commands] 00 54 25 d9 1f 00 80 00 00 00 00 00 00 03:57:09.333 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 00 d9 53 00 1f 25 00 00 00 00:00:32.896 NOP [Abort queued commands] Error 1660 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 b8 00 51 00 00 e0 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 5d 25 25 46 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 a0 25 54 00 46 25 00 00 00 00:00:45.240 NOP [Abort queued commands] 00 53 25 25 46 00 08 00 98 00 00 00 00 00:40:42.836 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 88 25 53 00 46 25 00 00 00 00:00:36.872 NOP [Abort queued commands] Error 1659 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 31 25 22 46 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 80 22 30 00 46 25 00 00 00 00:00:00.128 NOP [Abort queued commands] 00 2f 25 22 46 00 80 00 00 00 00 00 00 00:37:26.192 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 00 22 2e 00 46 25 00 00 00 00:00:32.896 NOP [Abort queued commands] Error 1658 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 8f 25 22 3a 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 80 22 8e 00 3a 25 00 00 00 00:00:00.128 NOP [Abort queued commands] 00 8d 25 22 3a 00 80 00 00 00 00 00 00 00:37:23.214 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 00 22 8c 00 3a 25 00 00 00 00:00:32.896 NOP [Abort queued commands] Error 1657 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 b8 00 51 00 00 e0 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 cd 25 7e 69 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 32 00 00 a0 7e c1 02 69 25 00 00 00 00:00:45.240 NOP [Abort queued commands] 02 bf 25 7e 69 00 1e 00 fb 00 00 00 02 02:18:04.608 [RESERVED] 00 01 00 00 19 7e bc 02 69 25 00 00 00 00:00:43.808 NOP [Abort queued commands] Error 1656 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 d7 25 7b 14 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 80 7b d7 00 14 25 00 00 00 00:00:00.128 NOP [Abort queued commands] 00 d5 25 7b 14 00 80 00 00 00 00 00 00 02:14:26.262 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 00 7b d5 00 14 25 00 00 00 00:00:32.896 NOP [Abort queued commands] Error 1655 [22] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 00 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 35 25 7b 09 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 80 7b 35 00 09 25 00 00 00 00:00:00.128 NOP [Abort queued commands] 00 34 25 7b 09 00 80 00 00 00 00 00 00 02:14:23.284 NOP [Reserved subcommand] [OBS-ACS-2] 00 80 00 00 00 7b 33 00 09 25 00 00 00 00:00:32.896 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 1269 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 28/30 Celsius Lifetime Min/Max Temperature: 24/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/85 Celsius Temperature History Size (Index): 128 (112) Index Estimated Time Temperature Celsius 113 2023-06-27 11:11 36 ***************** ... ..(115 skipped). .. ***************** 101 2023-06-27 13:07 36 ***************** 102 2023-06-27 13:08 ? - 103 2023-06-27 13:09 28 ********* 104 2023-06-27 13:10 29 ********** 105 2023-06-27 13:11 29 ********** 106 2023-06-27 13:12 30 *********** 107 2023-06-27 13:13 ? - 108 2023-06-27 13:14 28 ********* 109 2023-06-27 13:15 29 ********** 110 2023-06-27 13:16 29 ********** 111 2023-06-27 13:17 30 *********** 112 2023-06-27 13:18 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x8000 4 334 Vendor specific