/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.2-desktop-3omv2590] (OpenMandriva Lx 7.4-1) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD20EARS-60MVWB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 51.0AB51 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Form Factor: 3.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Aug 12 17:26:01 2025 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (36480) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 352) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 4 3 Spin_Up_Time POS--K 253 253 021 - 966 4 Start_Stop_Count -O--CK 079 079 000 - 21054 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-K 100 253 051 - 0 9 Power_On_Hours -O--CK 066 066 000 - 25262 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 079 079 000 - 21050 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 094 078 000 - 43 188 Command_Timeout -O--CK 094 078 000 - 196655 190 Airflow_Temperature_Cel -O---K 077 049 040 - 23 (Min/Max 22/23) 192 Power-Off_Retract_Count -O--CK 200 200 000 - 527 193 Load_Cycle_Count -O--CK 194 194 000 - 20526 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 15 198 Offline_Uncorrectable ----CK 200 200 000 - 13 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 27 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 43 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 43 [18] occurred at disk power-on lifetime: 25261 hours (1052 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 17 1a f8 58 40 00 Error: UNC at LBA = 0x171af858 = 387643480 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 d8 00 00 17 1a f8 58 40 08 02:05:15.555 READ FPDMA QUEUED 60 00 08 00 d0 00 00 17 1a f8 50 40 08 02:05:15.040 READ FPDMA QUEUED 60 00 08 00 c8 00 00 17 1a f8 48 40 08 02:05:15.040 READ FPDMA QUEUED 60 00 08 00 c0 00 00 17 1a f8 40 40 08 02:05:15.040 READ FPDMA QUEUED 60 00 08 00 b8 00 00 17 1a f8 38 40 08 02:05:15.040 READ FPDMA QUEUED Error 42 [17] occurred at disk power-on lifetime: 25261 hours (1052 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 17 1a f8 e0 40 00 Error: UNC at LBA = 0x171af8e0 = 387643616 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 70 00 00 17 1a f7 f0 40 08 02:05:12.208 READ FPDMA QUEUED 60 00 08 00 60 00 00 17 1a f7 e8 40 08 02:05:12.207 READ FPDMA QUEUED 60 00 08 00 80 00 00 17 1a f7 e0 40 08 02:05:12.191 READ FPDMA QUEUED 60 01 00 00 68 00 00 17 1a f8 e0 40 08 02:05:12.191 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 02:05:12.191 SET FEATURES [Enable SATA feature] Error 41 [16] occurred at disk power-on lifetime: 25261 hours (1052 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 17 1a f8 78 40 00 Error: UNC at LBA = 0x171af878 = 387643512 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 48 00 00 17 1a f7 e0 40 08 02:05:09.415 READ FPDMA QUEUED 60 01 00 00 40 00 00 17 1a f6 e0 40 08 02:05:09.413 READ FPDMA QUEUED 60 01 00 00 38 00 00 17 1a f5 e0 40 08 02:05:09.412 READ FPDMA QUEUED 60 01 00 00 30 00 00 17 1a f4 e0 40 08 02:05:09.410 READ FPDMA QUEUED 60 01 00 00 28 00 00 17 1a f3 e0 40 08 02:05:09.409 READ FPDMA QUEUED Error 40 [15] occurred at disk power-on lifetime: 25260 hours (1052 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 17 1a f8 58 40 00 Error: UNC at LBA = 0x171af858 = 387643480 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 70 00 00 17 1a f8 58 40 08 00:48:25.216 READ FPDMA QUEUED 60 00 08 00 68 00 00 17 1a f8 50 40 08 00:48:24.666 READ FPDMA QUEUED 60 00 08 00 60 00 00 17 1a f8 48 40 08 00:48:24.666 READ FPDMA QUEUED 60 00 08 00 58 00 00 17 1a f8 40 40 08 00:48:24.666 READ FPDMA QUEUED 60 00 08 00 50 00 00 17 1a f8 38 40 08 00:48:24.666 READ FPDMA QUEUED Error 39 [14] occurred at disk power-on lifetime: 25260 hours (1052 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 17 1a f8 c0 40 00 Error: UNC at LBA = 0x171af8c0 = 387643584 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 d0 00 00 17 1a f7 d8 40 08 00:48:21.834 READ FPDMA QUEUED 60 00 08 00 c8 00 00 17 1a f7 d0 40 08 00:48:21.834 READ FPDMA QUEUED 60 00 08 00 c0 00 00 17 1a f7 c8 40 08 00:48:21.834 READ FPDMA QUEUED 60 00 08 00 b8 00 00 17 1a f7 c0 40 08 00:48:21.834 READ FPDMA QUEUED 60 00 08 00 60 00 00 17 1a f7 b8 40 08 00:48:21.822 READ FPDMA QUEUED Error 38 [13] occurred at disk power-on lifetime: 25260 hours (1052 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 17 1a f8 58 40 00 Error: UNC at LBA = 0x171af858 = 387643480 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 a8 00 00 17 1a f7 b8 40 08 00:48:19.031 READ FPDMA QUEUED 60 01 00 00 a0 00 00 17 1a f6 b8 40 08 00:48:19.029 READ FPDMA QUEUED 60 01 00 00 98 00 00 17 1a f5 b8 40 08 00:48:19.028 READ FPDMA QUEUED 60 01 00 00 90 00 00 17 1a f4 b8 40 08 00:48:19.026 READ FPDMA QUEUED 60 01 00 00 88 00 00 17 1a f3 b8 40 08 00:48:19.025 READ FPDMA QUEUED Error 37 [12] occurred at disk power-on lifetime: 25250 hours (1052 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 17 a7 91 f0 40 00 Error: UNC at LBA = 0x17a791f0 = 396857840 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 e0 00 00 17 a7 90 f8 40 08 05:11:36.039 READ FPDMA QUEUED 60 00 08 00 30 00 00 17 a7 90 f0 40 08 05:11:36.028 READ FPDMA QUEUED 60 01 00 00 28 00 00 17 a7 91 f0 40 08 05:11:36.028 READ FPDMA QUEUED e5 00 00 00 00 00 00 00 00 00 00 00 08 05:11:36.028 CHECK POWER MODE ef 00 10 00 02 00 00 00 00 00 00 a0 08 05:11:36.028 SET FEATURES [Enable SATA feature] Error 36 [11] occurred at disk power-on lifetime: 25250 hours (1052 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 17 a7 91 b0 40 00 Error: UNC at LBA = 0x17a791b0 = 396857776 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 d0 00 00 17 a7 90 f0 40 08 05:11:33.030 READ FPDMA QUEUED 60 01 00 00 c8 00 00 17 a7 8f f0 40 08 05:11:33.029 READ FPDMA QUEUED 60 01 00 00 c0 00 00 17 a7 8e f0 40 08 05:11:33.028 READ FPDMA QUEUED 60 01 00 00 b8 00 00 17 a7 8d f0 40 08 05:11:33.019 READ FPDMA QUEUED 60 00 08 00 b0 00 00 0e fd de 08 40 08 05:11:33.014 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5669 - # 2 Short offline Completed without error 00% 5358 - # 3 Short offline Interrupted (host reset) 90% 5113 - # 4 Short offline Completed without error 00% 4553 - # 5 Short offline Completed without error 00% 3505 - # 6 Extended offline Interrupted (host reset) 90% 1 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 23 Celsius Power Cycle Min/Max Temperature: 22/23 Celsius Lifetime Min/Max Temperature: 20/51 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (18) Index Estimated Time Temperature Celsius 19 2025-08-12 15:19 30 *********** ... ..( 11 skipped). .. *********** 31 2025-08-12 15:31 30 *********** 32 2025-08-12 15:32 31 ************ ... ..( 17 skipped). .. ************ 50 2025-08-12 15:50 31 ************ 51 2025-08-12 15:51 32 ************* 52 2025-08-12 15:52 31 ************ 53 2025-08-12 15:53 31 ************ 54 2025-08-12 15:54 32 ************* 55 2025-08-12 15:55 32 ************* 56 2025-08-12 15:56 31 ************ 57 2025-08-12 15:57 32 ************* 58 2025-08-12 15:58 31 ************ 59 2025-08-12 15:59 32 ************* 60 2025-08-12 16:00 32 ************* 61 2025-08-12 16:01 31 ************ ... ..( 6 skipped). .. ************ 68 2025-08-12 16:08 31 ************ 69 2025-08-12 16:09 30 *********** ... ..( 45 skipped). .. *********** 115 2025-08-12 16:55 30 *********** 116 2025-08-12 16:56 ? - 117 2025-08-12 16:57 31 ************ 118 2025-08-12 16:58 ? - 119 2025-08-12 16:59 19 - 120 2025-08-12 17:00 ? - 121 2025-08-12 17:01 19 - 122 2025-08-12 17:02 ? - 123 2025-08-12 17:03 20 * 124 2025-08-12 17:04 20 * 125 2025-08-12 17:05 21 ** ... ..( 2 skipped). .. ** 0 2025-08-12 17:08 21 ** 1 2025-08-12 17:09 22 *** 2 2025-08-12 17:10 ? - 3 2025-08-12 17:11 23 **** 4 2025-08-12 17:12 ? - 5 2025-08-12 17:13 23 **** 6 2025-08-12 17:14 ? - 7 2025-08-12 17:15 23 **** 8 2025-08-12 17:16 ? - 9 2025-08-12 17:17 23 **** 10 2025-08-12 17:18 ? - 11 2025-08-12 17:19 22 *** ... ..( 4 skipped). .. *** 16 2025-08-12 17:24 22 *** 17 2025-08-12 17:25 23 **** 18 2025-08-12 17:26 23 **** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 464 Vendor specific