/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.8.0-47-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD3200AAJS-22L7A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.03E01 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sat Oct 19 18:18:14 2024 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5760) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 70) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 137 133 021 - 4125 4 Start_Stop_Count -O--CK 095 095 000 - 5367 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 084 084 000 - 12292 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4029 192 Power-Off_Retract_Count -O--CK 200 200 000 - 580 193 Load_Cycle_Count -O--CK 199 199 000 - 5367 194 Temperature_Celsius -O---K 110 085 000 - 33 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 2 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2226 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2226 [17] occurred at disk power-on lifetime: 9317 hours (388 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 02 61 00 8b a8 e0 00 Error: UNC 256 sectors at LBA = 0x261008ba8 = 10217360296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 02 8b 61 a8 e0 08 00:10:37.155 READ DMA EXT 25 00 00 00 80 00 00 02 84 93 c0 e0 08 00:10:37.155 READ DMA EXT 25 00 00 00 02 00 00 02 80 ba 42 e0 08 00:10:37.154 READ DMA EXT ea 00 00 00 00 40 3c 9f 00 00 00 e0 08 00:10:37.099 FLUSH CACHE EXT 25 00 00 00 40 00 00 04 40 3c 60 e0 08 00:10:37.086 READ DMA EXT Error 2225 [16] occurred at disk power-on lifetime: 9317 hours (388 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 02 61 00 8b a8 e0 00 Error: UNC 128 sectors at LBA = 0x261008ba8 = 10217360296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 02 8b 61 a8 e0 08 00:10:34.856 READ DMA EXT 35 00 00 00 08 00 00 02 84 a8 c8 e0 08 00:10:34.856 WRITE DMA EXT 25 00 00 00 25 00 00 02 84 48 00 e0 08 00:10:34.856 READ DMA EXT 25 00 00 01 00 00 00 02 84 47 00 e0 08 00:10:34.855 READ DMA EXT 25 00 00 00 03 00 00 02 80 ba 44 e0 08 00:10:34.855 READ DMA EXT Error 2224 [15] occurred at disk power-on lifetime: 9317 hours (388 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 02 61 00 8b a8 e0 00 Error: UNC 128 sectors at LBA = 0x261008ba8 = 10217360296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 02 8b 61 a8 e0 08 00:10:32.474 READ DMA EXT 25 00 00 00 80 00 00 02 84 46 00 e0 08 00:10:32.464 READ DMA EXT 35 00 00 01 00 00 00 0d b9 c2 40 e0 08 00:10:32.464 WRITE DMA EXT 35 00 00 01 00 00 00 0d b9 c1 40 e0 08 00:10:32.463 WRITE DMA EXT 35 00 00 00 10 00 00 05 6a 20 80 e0 08 00:10:32.463 WRITE DMA EXT Error 2223 [14] occurred at disk power-on lifetime: 9317 hours (388 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 02 61 00 8b a8 e0 00 Error: UNC 128 sectors at LBA = 0x261008ba8 = 10217360296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 02 8b 61 a8 e0 08 00:10:30.229 READ DMA EXT 25 00 00 00 dc 00 00 02 83 af a0 e0 08 00:10:30.220 READ DMA EXT 35 00 00 00 08 00 00 02 80 16 b0 e0 08 00:10:30.220 WRITE DMA EXT 35 00 00 01 00 00 00 0d b9 c0 40 e0 08 00:10:30.219 WRITE DMA EXT 35 00 00 01 00 00 00 0d b9 bf 40 e0 08 00:10:30.218 WRITE DMA EXT Error 2222 [13] occurred at disk power-on lifetime: 9317 hours (388 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 02 61 00 8b a8 e0 00 Error: UNC 128 sectors at LBA = 0x261008ba8 = 10217360296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 02 8b 61 a8 e0 08 00:10:28.007 READ DMA EXT 25 00 00 00 80 00 00 02 83 af 20 e0 08 00:10:28.007 READ DMA EXT 35 00 00 00 10 00 00 05 6a 1b 40 e0 08 00:10:28.006 WRITE DMA EXT 35 00 00 00 10 00 00 05 6a 15 d0 e0 08 00:10:28.006 WRITE DMA EXT 35 00 00 00 10 00 00 05 6a 14 e0 e0 08 00:10:28.006 WRITE DMA EXT Error 2221 [12] occurred at disk power-on lifetime: 9317 hours (388 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 02 61 00 8b a8 e0 00 Error: UNC 128 sectors at LBA = 0x261008ba8 = 10217360296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 02 8b 61 a8 e0 08 00:10:25.238 READ DMA EXT 25 00 00 00 40 00 00 04 40 3e 90 e0 08 00:10:25.232 READ DMA EXT 35 00 00 00 08 00 00 02 de 08 08 e0 08 00:10:25.232 WRITE DMA EXT 25 00 00 00 80 00 00 02 93 2f 80 e0 08 00:10:25.223 READ DMA EXT 25 00 00 00 80 00 00 02 92 91 d0 e0 08 00:10:25.211 READ DMA EXT Error 2220 [11] occurred at disk power-on lifetime: 9317 hours (388 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 02 61 00 8b a8 e0 00 Error: UNC 128 sectors at LBA = 0x261008ba8 = 10217360296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 02 8b 61 a8 e0 08 00:10:22.866 READ DMA EXT 35 00 00 00 08 00 00 02 80 68 c8 e0 08 00:10:22.866 WRITE DMA EXT 35 00 00 00 08 00 00 02 80 43 d0 e0 08 00:10:22.866 WRITE DMA EXT 35 00 00 00 10 00 00 05 6b 0e 00 e0 08 00:10:22.866 WRITE DMA EXT 35 00 00 00 10 00 00 05 6a 8e 00 e0 08 00:10:22.866 WRITE DMA EXT Error 2219 [10] occurred at disk power-on lifetime: 9317 hours (388 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 02 61 00 8b a8 e0 00 Error: UNC 128 sectors at LBA = 0x261008ba8 = 10217360296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 02 8b 61 a8 e0 08 00:10:20.634 READ DMA EXT 35 00 00 00 08 00 00 02 80 34 20 e0 08 00:10:20.634 WRITE DMA EXT 35 00 00 00 10 00 00 05 6b 9a a0 e0 08 00:10:20.634 WRITE DMA EXT 35 00 00 00 10 00 00 05 6b 13 50 e0 08 00:10:20.634 WRITE DMA EXT 35 00 00 00 10 00 00 05 6a 21 50 e0 08 00:10:20.633 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 30/33 Celsius Lifetime Min/Max Temperature: 20/57 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (304) Index Estimated Time Temperature Celsius 305 2024-10-19 10:21 33 ************** ... ..( 71 skipped). .. ************** 377 2024-10-19 11:33 33 ************** 378 2024-10-19 11:34 34 *************** ... ..( 30 skipped). .. *************** 409 2024-10-19 12:05 34 *************** 410 2024-10-19 12:06 ? - 411 2024-10-19 12:07 35 **************** 412 2024-10-19 12:08 ? - 413 2024-10-19 12:09 35 **************** 414 2024-10-19 12:10 34 *************** ... ..( 3 skipped). .. *************** 418 2024-10-19 12:14 34 *************** 419 2024-10-19 12:15 ? - 420 2024-10-19 12:16 35 **************** 421 2024-10-19 12:17 34 *************** 422 2024-10-19 12:18 ? - 423 2024-10-19 12:19 35 **************** 424 2024-10-19 12:20 34 *************** ... ..( 3 skipped). .. *************** 428 2024-10-19 12:24 34 *************** 429 2024-10-19 12:25 ? - 430 2024-10-19 12:26 35 **************** 431 2024-10-19 12:27 34 *************** ... ..( 4 skipped). .. *************** 436 2024-10-19 12:32 34 *************** 437 2024-10-19 12:33 ? - 438 2024-10-19 12:34 35 **************** 439 2024-10-19 12:35 34 *************** ... ..( 3 skipped). .. *************** 443 2024-10-19 12:39 34 *************** 444 2024-10-19 12:40 35 **************** 445 2024-10-19 12:41 34 *************** ... ..( 19 skipped). .. *************** 465 2024-10-19 13:01 34 *************** 466 2024-10-19 13:02 33 ************** ... ..( 2 skipped). .. ************** 469 2024-10-19 13:05 33 ************** 470 2024-10-19 13:06 34 *************** ... ..( 23 skipped). .. *************** 16 2024-10-19 13:30 34 *************** 17 2024-10-19 13:31 33 ************** 18 2024-10-19 13:32 34 *************** ... ..(131 skipped). .. *************** 150 2024-10-19 15:44 34 *************** 151 2024-10-19 15:45 ? - 152 2024-10-19 15:46 20 * 153 2024-10-19 15:47 20 * 154 2024-10-19 15:48 22 *** 155 2024-10-19 15:49 ? - 156 2024-10-19 15:50 22 *** 157 2024-10-19 15:51 23 **** 158 2024-10-19 15:52 23 **** 159 2024-10-19 15:53 ? - 160 2024-10-19 15:54 25 ****** 161 2024-10-19 15:55 ? - 162 2024-10-19 15:56 27 ******** 163 2024-10-19 15:57 27 ******** 164 2024-10-19 15:58 ? - 165 2024-10-19 15:59 28 ********* 166 2024-10-19 16:00 29 ********** 167 2024-10-19 16:01 29 ********** 168 2024-10-19 16:02 29 ********** 169 2024-10-19 16:03 ? - 170 2024-10-19 16:04 30 *********** ... ..( 2 skipped). .. *********** 173 2024-10-19 16:07 30 *********** 174 2024-10-19 16:08 31 ************ ... ..( 15 skipped). .. ************ 190 2024-10-19 16:24 31 ************ 191 2024-10-19 16:25 32 ************* ... ..( 41 skipped). .. ************* 233 2024-10-19 17:07 32 ************* 234 2024-10-19 17:08 33 ************** ... ..( 30 skipped). .. ************** 265 2024-10-19 17:39 33 ************** 266 2024-10-19 17:40 32 ************* 267 2024-10-19 17:41 33 ************** ... ..( 36 skipped). .. ************** 304 2024-10-19 18:18 33 ************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x8000 4 12543 Vendor specific /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.8.0-47-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD5000AAKX-001CA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 15.01H15 User Capacity: 500,106,780,160 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Oct 19 18:18:14 2024 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8460) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 86) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 142 141 021 - 3866 4 Start_Stop_Count -O--CK 099 099 000 - 1898 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 078 078 000 - 16519 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1422 192 Power-Off_Retract_Count -O--CK 200 200 000 - 214 193 Load_Cycle_Count -O--CK 200 200 000 - 1683 194 Temperature_Celsius -O---K 111 089 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 433 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 433 [0] occurred at disk power-on lifetime: 15754 hours (656 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 05 31 2d 74 e0 00 Error: UNC 1 sectors at LBA = 0x05312d74 = 87108980 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 05 31 2d 74 e0 00 02:46:45.255 READ DMA EXT 25 00 00 00 01 00 00 05 31 2d 73 e0 00 02:46:45.255 READ DMA EXT 25 00 00 00 01 00 00 05 31 2d 72 e0 00 02:46:45.254 READ DMA EXT 25 00 00 00 01 00 00 05 31 2d 71 e0 00 02:46:45.254 READ DMA EXT 25 00 00 00 01 00 00 05 31 2d 70 e0 00 02:46:45.254 READ DMA EXT Error 432 [23] occurred at disk power-on lifetime: 15754 hours (656 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 05 31 2d 74 e0 00 Error: UNC 32 sectors at LBA = 0x05312d74 = 87108980 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 05 31 2d 60 e0 00 02:46:43.479 READ DMA EXT 25 00 00 00 20 00 00 04 3d 99 c0 e0 00 02:46:43.472 READ DMA EXT 35 00 00 00 d8 00 00 04 3d 97 f8 e0 00 02:46:43.471 WRITE DMA EXT 35 00 00 01 00 00 00 04 3d 96 f8 e0 00 02:46:43.470 WRITE DMA EXT 35 00 00 01 00 00 00 04 3d 95 f8 e0 00 02:46:43.469 WRITE DMA EXT Error 431 [22] occurred at disk power-on lifetime: 15751 hours (656 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 05 31 2d 74 e0 00 Error: UNC 1 sectors at LBA = 0x05312d74 = 87108980 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 05 31 2d 74 e0 00 00:04:57.961 READ DMA EXT 25 00 00 00 40 00 00 04 d0 18 78 e0 00 00:04:57.951 READ DMA EXT 35 00 00 00 10 00 00 00 23 20 c8 e0 00 00:04:57.951 WRITE DMA EXT 25 00 00 01 00 00 00 04 96 b6 d0 e0 00 00:04:57.950 READ DMA EXT 25 00 00 01 00 00 00 04 96 b5 d0 e0 00 00:04:57.950 READ DMA EXT Error 430 [21] occurred at disk power-on lifetime: 15751 hours (656 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 05 31 2d 74 e0 00 Error: UNC 32 sectors at LBA = 0x05312d74 = 87108980 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 05 31 2d 60 e0 00 00:04:55.776 READ DMA EXT 35 00 00 00 ef 00 00 06 5e fd 20 e0 00 00:04:55.775 WRITE DMA EXT 35 00 00 00 10 00 00 05 f3 b3 70 e0 00 00:04:55.775 WRITE DMA EXT 35 00 00 00 80 00 00 05 20 6d c0 e0 00 00:04:55.774 WRITE DMA EXT 35 00 00 00 f8 00 00 04 bb 52 20 e0 00 00:04:55.774 WRITE DMA EXT Error 429 [20] occurred at disk power-on lifetime: 15740 hours (655 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 05 31 2d 74 e0 00 Error: UNC 1 sectors at LBA = 0x05312d74 = 87108980 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 05 31 2d 74 e0 00 00:14:04.883 READ DMA EXT 25 00 00 00 01 00 00 05 31 2d 73 e0 00 00:14:04.882 READ DMA EXT 25 00 00 00 08 00 00 00 5d 87 78 e0 00 00:14:04.871 READ DMA EXT 25 00 00 00 01 00 00 05 31 2d 72 e0 00 00:14:04.870 READ DMA EXT 25 00 00 00 20 00 00 05 69 25 40 e0 00 00:14:04.862 READ DMA EXT Error 428 [19] occurred at disk power-on lifetime: 15740 hours (655 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 40 00 00 05 31 2d 74 e0 00 Error: UNC 64 sectors at LBA = 0x05312d74 = 87108980 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 05 31 2d 40 e0 00 00:14:02.821 READ DMA EXT 35 00 00 00 20 00 00 08 49 77 20 e0 00 00:14:02.821 WRITE DMA EXT 25 00 00 00 40 00 00 05 69 09 a8 e0 00 00:14:02.811 READ DMA EXT 35 00 00 00 40 00 00 08 4c 3b a0 e0 00 00:14:02.810 WRITE DMA EXT 35 00 00 00 20 00 00 04 6e 26 60 e0 00 00:14:02.810 WRITE DMA EXT Error 427 [18] occurred at disk power-on lifetime: 15714 hours (654 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 05 31 2d 74 e0 00 Error: UNC 1 sectors at LBA = 0x05312d74 = 87108980 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 05 31 2d 74 e0 00 00:10:37.118 READ DMA EXT 25 00 00 00 01 00 00 05 31 2d 73 e0 00 00:10:37.118 READ DMA EXT 35 00 00 01 00 00 00 07 58 4b 60 e0 00 00:10:37.105 WRITE DMA EXT 35 00 00 01 00 00 00 07 58 4a 60 e0 00 00:10:37.105 WRITE DMA EXT 35 00 00 01 00 00 00 07 58 49 60 e0 00 00:10:37.104 WRITE DMA EXT Error 426 [17] occurred at disk power-on lifetime: 15714 hours (654 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 20 00 00 05 31 2d 74 e0 00 Error: UNC 32 sectors at LBA = 0x05312d74 = 87108980 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 00 05 31 2d 60 e0 00 00:10:35.323 READ DMA EXT ea 00 00 00 00 71 bc 8f 00 00 00 e0 00 00:10:35.263 FLUSH CACHE EXT 35 00 00 00 58 00 00 00 71 bc 38 e0 00 00:10:35.263 WRITE DMA EXT 25 00 00 00 08 00 00 05 90 9b c8 e0 00 00:10:35.254 READ DMA EXT 35 00 00 00 28 00 00 04 e3 ea 98 e0 00 00:10:35.253 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 29/32 Celsius Lifetime Min/Max Temperature: 21/54 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (333) Index Estimated Time Temperature Celsius 334 2024-10-19 10:21 32 ************* ... ..( 16 skipped). .. ************* 351 2024-10-19 10:38 32 ************* 352 2024-10-19 10:39 33 ************** ... ..( 28 skipped). .. ************** 381 2024-10-19 11:08 33 ************** 382 2024-10-19 11:09 ? - 383 2024-10-19 11:10 21 ** 384 2024-10-19 11:11 21 ** 385 2024-10-19 11:12 ? - 386 2024-10-19 11:13 23 **** 387 2024-10-19 11:14 23 **** 388 2024-10-19 11:15 ? - 389 2024-10-19 11:16 25 ****** 390 2024-10-19 11:17 ? - 391 2024-10-19 11:18 27 ******** 392 2024-10-19 11:19 26 ******* 393 2024-10-19 11:20 ? - 394 2024-10-19 11:21 27 ******** 395 2024-10-19 11:22 27 ******** 396 2024-10-19 11:23 28 ********* 397 2024-10-19 11:24 ? - 398 2024-10-19 11:25 29 ********** ... ..( 3 skipped). .. ********** 402 2024-10-19 11:29 29 ********** 403 2024-10-19 11:30 30 *********** ... ..( 6 skipped). .. *********** 410 2024-10-19 11:37 30 *********** 411 2024-10-19 11:38 31 ************ ... ..( 7 skipped). .. ************ 419 2024-10-19 11:46 31 ************ 420 2024-10-19 11:47 32 ************* 421 2024-10-19 11:48 31 ************ 422 2024-10-19 11:49 32 ************* 423 2024-10-19 11:50 32 ************* 424 2024-10-19 11:51 31 ************ 425 2024-10-19 11:52 31 ************ 426 2024-10-19 11:53 32 ************* ... ..(178 skipped). .. ************* 127 2024-10-19 14:52 32 ************* 128 2024-10-19 14:53 33 ************** ... ..( 42 skipped). .. ************** 171 2024-10-19 15:36 33 ************** 172 2024-10-19 15:37 ? - 173 2024-10-19 15:38 33 ************** 174 2024-10-19 15:39 ? - 175 2024-10-19 15:40 33 ************** 176 2024-10-19 15:41 33 ************** 177 2024-10-19 15:42 ? - 178 2024-10-19 15:43 33 ************** 179 2024-10-19 15:44 33 ************** 180 2024-10-19 15:45 ? - 181 2024-10-19 15:46 33 ************** ... ..( 4 skipped). .. ************** 186 2024-10-19 15:51 33 ************** 187 2024-10-19 15:52 ? - 188 2024-10-19 15:53 33 ************** 189 2024-10-19 15:54 33 ************** 190 2024-10-19 15:55 ? - 191 2024-10-19 15:56 33 ************** ... ..(140 skipped). .. ************** 332 2024-10-19 18:17 33 ************** 333 2024-10-19 18:18 32 ************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 12537 Vendor specific /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.8.0-47-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green Device Model: WDC WD5000AAVS-00ZTB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01B01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sat Oct 19 18:18:14 2024 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13980) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 163) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 216 3 Spin_Up_Time PO---- 158 153 021 - 5075 4 Start_Stop_Count -O--CK 092 092 000 - 8519 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 048 048 000 - 38152 10 Spin_Retry_Count -O--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1627 192 Power-Off_Retract_Count -O--CK 200 200 000 - 290 193 Load_Cycle_Count -O--CK 150 150 000 - 151979 194 Temperature_Celsius -O---K 115 078 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 175 051 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 389 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 389 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 01 00 00 51 e0 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 a0 25 0c f4 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 01 00 00 50 0c f4 a0 25 00 00 00 08 00:00:20.737 DEVICE RESET 00 9f 25 0c f4 00 4f 01 00 08 00 00 00 00:14:09.056 NOP [Reserved subcommand] [OBS-ACS-2] 08 01 00 00 4d 0c f4 9f 25 00 00 00 08 00:00:19.969 DEVICE RESET Error 388 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 20 00 00 51 e0 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 f4 25 0c e3 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 08 00 00 20 0c e3 f4 35 00 00 00 08 00:00:16.416 DEVICE RESET 09 f3 35 0c e3 00 e0 20 00 08 00 00 09 00:14:04.787 [RESERVED] 08 20 00 00 20 0c e3 f3 25 00 00 00 08 00:00:08.224 DEVICE RESET Error 387 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 01 00 00 51 e0 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 83 25 0a f4 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 01 00 00 50 0a f4 82 25 00 00 00 08 00:00:20.737 DEVICE RESET 00 82 25 0a f4 00 4f 01 00 08 00 00 00 00:11:57.954 NOP [Reserved subcommand] [OBS-ACS-2] 08 01 00 00 4d 0a f4 82 25 00 00 00 08 00:00:19.969 DEVICE RESET Error 386 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 00 51 e0 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 b6 25 0a e3 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 08 00 00 30 0a e3 b6 35 00 00 00 08 00:00:16.512 DEVICE RESET 00 b6 35 0a e3 00 20 08 00 08 00 00 08 00:11:53.654 NOP [Reserved subcommand] [OBS-ACS-2] 08 20 00 00 40 0a e3 b6 35 08 00 00 08 00:00:57.376 DEVICE RESET Error 385 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 00 51 40 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 36 60 2d 6f 00 00 00 00 00 00 00 0b 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 b8 08 00 68 2d 6f 35 61 00 00 00 00 00:00:28.864 NOP [Reserved subcommand] [OBS-ACS-2] 0d 2f 60 2d 6f 00 e2 b0 04 00 00 00 00 00:49:37.589 [RESERVED] 00 a0 01 00 50 2d 6f 2f 60 00 00 00 00 00:00:20.904 NOP [Don't abort queued commands] [OBS-ACS-2] Error 384 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 01 00 00 51 40 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c3 60 2d 5e 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 f0 08 00 00 2d 5e c3 61 00 00 00 00 00:00:16.392 NOP [Reserved subcommand] [OBS-ACS-2] 00 c3 61 2d 5e 00 d8 e8 20 00 00 00 00 00:49:33.379 NOP [Reserved subcommand] [OBS-ACS-2] 00 d8 10 00 48 2d 5e c3 61 00 00 00 00 00:00:47.328 NOP [Reserved subcommand] [OBS-ACS-2] Error 383 [22] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 00 51 e0 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 04 25 78 ce 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 02 00 00 ca 78 cd f4 25 00 00 00 08 00:00:00.000 DEVICE RESET 00 ed 25 78 bd 00 00 00 00 08 00 00 0b 02:11:52.941 NOP [Reserved subcommand] [OBS-ACS-2] 08 02 00 00 54 78 bd ec 35 0b 00 00 08 00:00:21.506 DEVICE RESET Error 382 [21] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 00 51 e0 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 ed 25 78 bd 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 02 00 00 54 78 bd ed 25 0b 00 00 08 00:00:00.000 DEVICE RESET 0b ea 25 78 bd 00 54 02 00 08 00 00 0b 02:11:52.940 REQUEST SENSE DATA EXT 08 02 00 00 4c 78 bd ea 35 0b 00 00 08 00:00:19.458 DEVICE RESET SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 26/32 Celsius Lifetime Min/Max Temperature: 20/69 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/85 Celsius Temperature History Size (Index): 128 (84) Index Estimated Time Temperature Celsius 85 2024-10-19 16:11 31 ************ 86 2024-10-19 16:12 31 ************ 87 2024-10-19 16:13 32 ************* ... ..( 3 skipped). .. ************* 91 2024-10-19 16:17 32 ************* 92 2024-10-19 16:18 31 ************ ... ..( 3 skipped). .. ************ 96 2024-10-19 16:22 31 ************ 97 2024-10-19 16:23 32 ************* ... ..( 3 skipped). .. ************* 101 2024-10-19 16:27 32 ************* 102 2024-10-19 16:28 31 ************ ... ..( 3 skipped). .. ************ 106 2024-10-19 16:32 31 ************ 107 2024-10-19 16:33 32 ************* ... ..( 3 skipped). .. ************* 111 2024-10-19 16:37 32 ************* 112 2024-10-19 16:38 31 ************ ... ..( 3 skipped). .. ************ 116 2024-10-19 16:42 31 ************ 117 2024-10-19 16:43 32 ************* ... ..( 3 skipped). .. ************* 121 2024-10-19 16:47 32 ************* 122 2024-10-19 16:48 31 ************ ... ..( 2 skipped). .. ************ 125 2024-10-19 16:51 31 ************ 126 2024-10-19 16:52 32 ************* ... ..( 4 skipped). .. ************* 3 2024-10-19 16:57 32 ************* 4 2024-10-19 16:58 31 ************ 5 2024-10-19 16:59 31 ************ 6 2024-10-19 17:00 31 ************ 7 2024-10-19 17:01 32 ************* ... ..( 5 skipped). .. ************* 13 2024-10-19 17:07 32 ************* 14 2024-10-19 17:08 31 ************ 15 2024-10-19 17:09 31 ************ 16 2024-10-19 17:10 31 ************ 17 2024-10-19 17:11 32 ************* ... ..( 5 skipped). .. ************* 23 2024-10-19 17:17 32 ************* 24 2024-10-19 17:18 31 ************ 25 2024-10-19 17:19 31 ************ 26 2024-10-19 17:20 31 ************ 27 2024-10-19 17:21 32 ************* ... ..( 5 skipped). .. ************* 33 2024-10-19 17:27 32 ************* 34 2024-10-19 17:28 31 ************ ... ..( 2 skipped). .. ************ 37 2024-10-19 17:31 31 ************ 38 2024-10-19 17:32 32 ************* ... ..( 4 skipped). .. ************* 43 2024-10-19 17:37 32 ************* 44 2024-10-19 17:38 31 ************ 45 2024-10-19 17:39 31 ************ 46 2024-10-19 17:40 31 ************ 47 2024-10-19 17:41 32 ************* ... ..( 5 skipped). .. ************* 53 2024-10-19 17:47 32 ************* 54 2024-10-19 17:48 31 ************ 55 2024-10-19 17:49 31 ************ 56 2024-10-19 17:50 31 ************ 57 2024-10-19 17:51 32 ************* ... ..( 5 skipped). .. ************* 63 2024-10-19 17:57 32 ************* 64 2024-10-19 17:58 31 ************ 65 2024-10-19 17:59 31 ************ 66 2024-10-19 18:00 31 ************ 67 2024-10-19 18:01 32 ************* ... ..( 5 skipped). .. ************* 73 2024-10-19 18:07 32 ************* 74 2024-10-19 18:08 31 ************ ... ..( 2 skipped). .. ************ 77 2024-10-19 18:11 31 ************ 78 2024-10-19 18:12 32 ************* ... ..( 4 skipped). .. ************* 83 2024-10-19 18:17 32 ************* 84 2024-10-19 18:18 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x8000 4 12544 Vendor specific