/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Blue Mobile Device Model: WDC WD5000LPCX-00VHAT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Nov 5 09:48:55 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8820) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 102) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 143 140 021 - 1825 4 Start_Stop_Count -O--CK 097 097 000 - 3238 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 089 089 000 - 8689 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3002 192 Power-Off_Retract_Count -O--CK 200 200 000 - 514 193 Load_Cycle_Count -O--CK 001 001 000 - 610667 194 Temperature_Celsius -O---K 109 083 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 48 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 8623 - # 2 Extended offline Completed without error 00% 8490 - # 3 Extended offline Completed without error 00% 8342 - # 4 Extended offline Completed without error 00% 8127 - # 5 Extended offline Completed without error 00% 8072 - # 6 Extended offline Completed without error 00% 7722 - # 7 Extended offline Completed without error 00% 7665 - # 8 Extended offline Completed without error 00% 7633 - # 9 Extended offline Completed without error 00% 7544 - #10 Extended offline Completed without error 00% 7524 - #11 Extended offline Completed without error 00% 7449 - #12 Extended offline Completed without error 00% 7431 - #13 Extended offline Interrupted (host reset) 80% 7253 - #14 Extended offline Completed without error 00% 7130 - #15 Extended offline Completed without error 00% 6878 - #16 Extended offline Completed without error 00% 6724 - #17 Extended offline Completed without error 00% 6573 - #18 Extended offline Completed without error 00% 6425 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 25/34 Celsius Lifetime Min/Max Temperature: 15/60 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (125) Index Estimated Time Temperature Celsius 126 2019-11-05 07:41 34 *************** 127 2019-11-05 07:42 35 **************** 0 2019-11-05 07:43 ? - 1 2019-11-05 07:44 32 ************* 2 2019-11-05 07:45 33 ************** 3 2019-11-05 07:46 33 ************** 4 2019-11-05 07:47 34 *************** 5 2019-11-05 07:48 35 **************** 6 2019-11-05 07:49 35 **************** 7 2019-11-05 07:50 36 ***************** ... ..( 2 skipped). .. ***************** 10 2019-11-05 07:53 36 ***************** 11 2019-11-05 07:54 37 ****************** ... ..( 7 skipped). .. ****************** 19 2019-11-05 08:02 37 ****************** 20 2019-11-05 08:03 ? - 21 2019-11-05 08:04 31 ************ 22 2019-11-05 08:05 31 ************ 23 2019-11-05 08:06 32 ************* 24 2019-11-05 08:07 32 ************* 25 2019-11-05 08:08 33 ************** ... ..( 2 skipped). .. ************** 28 2019-11-05 08:11 33 ************** 29 2019-11-05 08:12 34 *************** ... ..( 3 skipped). .. *************** 33 2019-11-05 08:16 34 *************** 34 2019-11-05 08:17 35 **************** ... ..( 7 skipped). .. **************** 42 2019-11-05 08:25 35 **************** 43 2019-11-05 08:26 36 ***************** ... ..( 2 skipped). .. ***************** 46 2019-11-05 08:29 36 ***************** 47 2019-11-05 08:30 ? - 48 2019-11-05 08:31 28 ********* 49 2019-11-05 08:32 28 ********* 50 2019-11-05 08:33 29 ********** 51 2019-11-05 08:34 30 *********** 52 2019-11-05 08:35 31 ************ 53 2019-11-05 08:36 31 ************ 54 2019-11-05 08:37 32 ************* 55 2019-11-05 08:38 33 ************** 56 2019-11-05 08:39 33 ************** 57 2019-11-05 08:40 34 *************** 58 2019-11-05 08:41 35 **************** 59 2019-11-05 08:42 35 **************** 60 2019-11-05 08:43 36 ***************** ... ..( 2 skipped). .. ***************** 63 2019-11-05 08:46 36 ***************** 64 2019-11-05 08:47 37 ****************** 65 2019-11-05 08:48 37 ****************** 66 2019-11-05 08:49 37 ****************** 67 2019-11-05 08:50 38 ******************* ... ..( 3 skipped). .. ******************* 71 2019-11-05 08:54 38 ******************* 72 2019-11-05 08:55 39 ******************** 73 2019-11-05 08:56 39 ******************** 74 2019-11-05 08:57 40 ********************* ... ..( 4 skipped). .. ********************* 79 2019-11-05 09:02 40 ********************* 80 2019-11-05 09:03 41 ********************** ... ..( 16 skipped). .. ********************** 97 2019-11-05 09:20 41 ********************** 98 2019-11-05 09:21 42 *********************** 99 2019-11-05 09:22 42 *********************** 100 2019-11-05 09:23 42 *********************** 101 2019-11-05 09:24 ? - 102 2019-11-05 09:25 25 ****** 103 2019-11-05 09:26 25 ****** 104 2019-11-05 09:27 26 ******* 105 2019-11-05 09:28 26 ******* 106 2019-11-05 09:29 27 ******** 107 2019-11-05 09:30 28 ********* ... ..( 2 skipped). .. ********* 110 2019-11-05 09:33 28 ********* 111 2019-11-05 09:34 29 ********** 112 2019-11-05 09:35 29 ********** 113 2019-11-05 09:36 30 *********** 114 2019-11-05 09:37 31 ************ ... ..( 2 skipped). .. ************ 117 2019-11-05 09:40 31 ************ 118 2019-11-05 09:41 32 ************* 119 2019-11-05 09:42 32 ************* 120 2019-11-05 09:43 32 ************* 121 2019-11-05 09:44 33 ************** 122 2019-11-05 09:45 33 ************** 123 2019-11-05 09:46 33 ************** 124 2019-11-05 09:47 34 *************** 125 2019-11-05 09:48 34 *************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1428 Vendor specific