Probe #d7edde223e of Gigabyte AB350-Gaming-CF Desktop Computer (AB350-Gaming)

Log: smartctl

/dev/sda smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.31-gentoo] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Ultrastar 7K4000 Device Model: Hitachi HUS724030ALE641 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: MJ8OA5F0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5706 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 29 04:26:04 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2], Master PW ID: 0xfffd === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 24) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 1) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 136 136 054 - 81 3 Spin_Up_Time POS--- 129 129 024 - 487 (Average 476) 4 Start_Stop_Count -O--C- 100 100 000 - 359 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 121 121 020 - 34 9 Power_On_Hours -O--C- 090 090 000 - 73900 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 206 192 Power-Off_Retract_Count -O--CK 098 098 000 - 3339 193 Load_Cycle_Count -O--C- 098 098 000 - 3339 194 Temperature_Celsius -O---- 153 153 000 - 39 (Min/Max 3/48) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 3 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80 GPL R/W 63 Host vendor specific log 0x81-0x9f GPL,SL R/W 16 Host vendor specific log 0xb2 GPL VS 63 Device vendor specific log 0xc8 GPL VS 617 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 3 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 [2] occurred at disk power-on lifetime: 20533 hours (855 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 11 00 01 15 63 1d a7 05 00 Error: ICRC, ABRT at LBA = 0x115631da7 = 4653784487 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 06 00 00 70 00 01 15 63 17 b8 40 00 3d+19:01:13.356 READ FPDMA QUEUED 60 05 00 00 68 00 01 15 63 12 b8 40 00 3d+19:01:13.351 READ FPDMA QUEUED 60 06 00 00 60 00 01 15 63 0c b8 40 00 3d+19:01:13.343 READ FPDMA QUEUED 60 05 00 00 58 00 01 15 63 07 b8 40 00 3d+19:01:13.337 READ FPDMA QUEUED 60 05 00 00 50 00 01 15 63 02 b8 40 00 3d+19:01:13.332 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 20533 hours (855 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 03 11 00 01 15 50 10 ef 05 00 Error: ICRC, ABRT at LBA = 0x1155010ef = 4652536047 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 05 00 00 10 00 01 15 50 0f 00 40 00 3d+19:01:06.319 READ FPDMA QUEUED 60 05 00 00 08 00 01 15 50 0a 00 40 00 3d+19:01:06.315 READ FPDMA QUEUED 60 05 00 00 00 00 01 15 50 05 00 40 00 3d+19:01:06.309 READ FPDMA QUEUED 60 05 00 00 f8 00 01 15 50 00 00 40 00 3d+19:01:06.305 READ FPDMA QUEUED 60 05 00 00 f0 00 01 15 4f fb 00 40 00 3d+19:01:06.298 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 20533 hours (855 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 91 00 01 15 44 cb 6f 05 00 Error: ICRC, ABRT at LBA = 0x11544cb6f = 4651797359 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 05 00 00 48 00 01 15 44 c7 00 40 00 3d+19:01:01.636 READ FPDMA QUEUED 60 05 00 00 40 00 01 15 44 c2 00 40 00 3d+19:01:01.631 READ FPDMA QUEUED 60 05 00 00 38 00 01 15 44 bd 00 40 00 3d+19:01:01.608 READ FPDMA QUEUED 60 00 28 00 30 00 00 f6 22 39 f8 40 00 3d+19:01:01.608 READ FPDMA QUEUED 60 05 00 00 28 00 01 15 44 b8 00 40 00 3d+19:01:01.601 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 8361 - # 2 Short offline Completed without error 00% 8337 - # 3 Extended offline Completed without error 00% 8321 - # 4 Short offline Completed without error 00% 8313 - # 5 Short offline Completed without error 00% 8289 - # 6 Short offline Completed without error 00% 8265 - # 7 Short offline Completed without error 00% 8241 - # 8 Short offline Completed without error 00% 8217 - # 9 Short offline Completed without error 00% 8193 - #10 Short offline Completed without error 00% 8169 - #11 Extended offline Completed without error 00% 8153 - #12 Short offline Completed without error 00% 8145 - #13 Short offline Completed without error 00% 8121 - #14 Short offline Completed without error 00% 8097 - #15 Short offline Completed without error 00% 8073 - #16 Short offline Completed without error 00% 8049 - #17 Short offline Completed without error 00% 8025 - #18 Short offline Completed without error 00% 8001 - #19 Extended offline Completed without error 00% 7985 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 34/44 Celsius Lifetime Min/Max Temperature: 3/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (88) Index Estimated Time Temperature Celsius 89 2025-06-29 02:19 39 ******************** ... ..(126 skipped). .. ******************** 88 2025-06-29 04:26 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 206 --- Lifetime Power-On Resets 0x01 0x018 6 106993659480 --- Logical Sectors Written 0x01 0x020 6 817967091 --- Number of Write Commands 0x01 0x028 6 1799024714965 --- Logical Sectors Read 0x01 0x030 6 3265296476 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 73888 --- Spindle Motor Power-on Hours 0x03 0x010 4 73887 --- Head Flying Hours 0x03 0x018 4 3339 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 820 --- Read Recovery Attempts 0x03 0x030 4 1 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 2 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 39 --- Current Temperature 0x05 0x010 1 38 N-- Average Short Term Temperature 0x05 0x018 1 38 N-- Average Long Term Temperature 0x05 0x020 1 48 --- Highest Temperature 0x05 0x028 1 3 --- Lowest Temperature 0x05 0x030 1 48 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 48 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1678 --- Number of Hardware Resets 0x06 0x010 4 1166 --- Number of ASR Events 0x06 0x018 4 3 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 29 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 20 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.31-gentoo] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba X300 Device Model: TOSHIBA HDWE150 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: FP1R User Capacity: 5,000,981,078,016 bytes [5.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5706 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 29 04:26:06 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 546) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 8601 4 Start_Stop_Count -O--CK 100 100 000 - 30 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 001 001 000 - 43237 10 Spin_Retry_Count PO--CK 100 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 29 191 G-Sense_Error_Rate -O--CK 100 100 000 - 1572 192 Power-Off_Retract_Count -O--CK 100 100 000 - 17 193 Load_Cycle_Count -O--CK 100 100 000 - 86 194 Temperature_Celsius -O---K 100 100 000 - 38 (Min/Max 23/48) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 253 000 - 3 220 Disk_Shift -O---- 100 100 000 - 0 222 Loaded_Hours -O--CK 001 001 000 - 43232 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 636 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 12288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa7 GPL VS 8 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 3 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 [2] occurred at disk power-on lifetime: 29973 hours (1248 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 10 00 01 99 69 e6 ff 40 00 Error: ICRC, ABRT at LBA = 0x19969e6ff = 6868821759 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 05 00 00 20 00 01 99 69 ec 00 40 00 23d+18:05:52.465 READ FPDMA QUEUED 60 05 00 00 18 00 01 99 69 e7 00 40 00 23d+18:05:52.461 READ FPDMA QUEUED 60 05 00 00 10 00 01 99 69 e2 00 40 00 23d+18:05:52.457 READ FPDMA QUEUED 60 05 00 00 08 00 01 99 69 dd 00 40 00 23d+18:05:52.453 READ FPDMA QUEUED 60 05 00 00 00 00 01 99 69 d8 00 40 00 23d+18:05:52.449 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 24932 hours (1038 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 08 00 01 af 82 6c ff 40 00 Error: ICRC, ABRT at LBA = 0x1af826cff = 7239527679 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 05 00 00 18 00 01 af 82 72 00 40 00 12d+12:41:49.187 READ FPDMA QUEUED 60 05 00 00 10 00 01 af 82 6d 00 40 00 12d+12:41:49.182 READ FPDMA QUEUED 60 05 00 00 08 00 01 af 82 68 00 40 00 12d+12:41:49.178 READ FPDMA QUEUED 60 05 00 00 00 00 01 af 82 63 00 40 00 12d+12:41:49.174 READ FPDMA QUEUED 60 05 00 00 f0 00 01 af 82 5e 00 40 00 12d+12:41:49.170 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 21237 hours (884 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 38 00 01 a2 18 4a ff 40 00 Error: ICRC, ABRT at LBA = 0x1a2184aff = 7014468351 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 05 00 00 c8 00 01 a2 18 7c 00 40 00 17:40:20.944 READ FPDMA QUEUED 60 05 00 00 c0 00 01 a2 18 77 00 40 00 17:40:20.939 READ FPDMA QUEUED 60 05 00 00 b8 00 01 a2 18 72 00 40 00 17:40:20.936 READ FPDMA QUEUED 60 05 00 00 b0 00 01 a2 18 6d 00 40 00 17:40:20.931 READ FPDMA QUEUED 60 05 00 00 90 00 01 a2 18 68 00 40 00 17:40:20.927 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 43234 - # 2 Short offline Completed without error 00% 43210 - # 3 Extended offline Completed without error 00% 43195 - # 4 Short offline Completed without error 00% 43186 - # 5 Short offline Completed without error 00% 43162 - # 6 Short offline Completed without error 00% 43138 - # 7 Short offline Completed without error 00% 43114 - # 8 Short offline Completed without error 00% 43090 - # 9 Short offline Completed without error 00% 43066 - #10 Short offline Completed without error 00% 43042 - #11 Extended offline Completed without error 00% 43027 - #12 Short offline Completed without error 00% 43018 - #13 Short offline Completed without error 00% 42994 - #14 Short offline Completed without error 00% 42970 - #15 Short offline Completed without error 00% 42946 - #16 Short offline Completed without error 00% 42922 - #17 Short offline Completed without error 00% 42898 - #18 Short offline Completed without error 00% 42874 - #19 Extended offline Completed without error 00% 42859 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 31/42 Celsius Lifetime Min/Max Temperature: 23/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (14) Index Estimated Time Temperature Celsius 15 2025-06-28 20:29 38 ******************* ... ..( 14 skipped). .. ******************* 30 2025-06-28 20:44 38 ******************* 31 2025-06-28 20:45 39 ******************** 32 2025-06-28 20:46 39 ******************** 33 2025-06-28 20:47 39 ******************** 34 2025-06-28 20:48 38 ******************* ... ..( 7 skipped). .. ******************* 42 2025-06-28 20:56 38 ******************* 43 2025-06-28 20:57 39 ******************** 44 2025-06-28 20:58 39 ******************** 45 2025-06-28 20:59 38 ******************* ... ..(108 skipped). .. ******************* 154 2025-06-28 22:48 38 ******************* 155 2025-06-28 22:49 37 ****************** 156 2025-06-28 22:50 38 ******************* ... ..( 2 skipped). .. ******************* 159 2025-06-28 22:53 38 ******************* 160 2025-06-28 22:54 37 ****************** 161 2025-06-28 22:55 38 ******************* ... ..( 2 skipped). .. ******************* 164 2025-06-28 22:58 38 ******************* 165 2025-06-28 22:59 37 ****************** 166 2025-06-28 23:00 37 ****************** 167 2025-06-28 23:01 38 ******************* 168 2025-06-28 23:02 37 ****************** ... ..( 15 skipped). .. ****************** 184 2025-06-28 23:18 37 ****************** 185 2025-06-28 23:19 38 ******************* 186 2025-06-28 23:20 37 ****************** 187 2025-06-28 23:21 38 ******************* ... ..( 60 skipped). .. ******************* 248 2025-06-29 00:22 38 ******************* 249 2025-06-29 00:23 37 ****************** 250 2025-06-29 00:24 38 ******************* ... ..( 3 skipped). .. ******************* 254 2025-06-29 00:28 38 ******************* 255 2025-06-29 00:29 37 ****************** 256 2025-06-29 00:30 37 ****************** 257 2025-06-29 00:31 38 ******************* ... ..( 31 skipped). .. ******************* 289 2025-06-29 01:03 38 ******************* 290 2025-06-29 01:04 37 ****************** 291 2025-06-29 01:05 38 ******************* ... ..( 59 skipped). .. ******************* 351 2025-06-29 02:05 38 ******************* 352 2025-06-29 02:06 37 ****************** 353 2025-06-29 02:07 38 ******************* ... ..( 28 skipped). .. ******************* 382 2025-06-29 02:36 38 ******************* 383 2025-06-29 02:37 37 ****************** 384 2025-06-29 02:38 38 ******************* 385 2025-06-29 02:39 38 ******************* 386 2025-06-29 02:40 37 ****************** 387 2025-06-29 02:41 38 ******************* 388 2025-06-29 02:42 38 ******************* 389 2025-06-29 02:43 38 ******************* 390 2025-06-29 02:44 37 ****************** 391 2025-06-29 02:45 38 ******************* ... ..( 5 skipped). .. ******************* 397 2025-06-29 02:51 38 ******************* 398 2025-06-29 02:52 37 ****************** 399 2025-06-29 02:53 37 ****************** 400 2025-06-29 02:54 38 ******************* 401 2025-06-29 02:55 38 ******************* 402 2025-06-29 02:56 37 ****************** 403 2025-06-29 02:57 38 ******************* ... ..( 4 skipped). .. ******************* 408 2025-06-29 03:02 38 ******************* 409 2025-06-29 03:03 37 ****************** 410 2025-06-29 03:04 38 ******************* ... ..( 3 skipped). .. ******************* 414 2025-06-29 03:08 38 ******************* 415 2025-06-29 03:09 37 ****************** 416 2025-06-29 03:10 38 ******************* ... ..( 15 skipped). .. ******************* 432 2025-06-29 03:26 38 ******************* 433 2025-06-29 03:27 37 ****************** 434 2025-06-29 03:28 38 ******************* 435 2025-06-29 03:29 37 ****************** 436 2025-06-29 03:30 38 ******************* ... ..( 2 skipped). .. ******************* 439 2025-06-29 03:33 38 ******************* 440 2025-06-29 03:34 37 ****************** 441 2025-06-29 03:35 37 ****************** 442 2025-06-29 03:36 38 ******************* 443 2025-06-29 03:37 37 ****************** ... ..( 4 skipped). .. ****************** 448 2025-06-29 03:42 37 ****************** 449 2025-06-29 03:43 38 ******************* 450 2025-06-29 03:44 38 ******************* 451 2025-06-29 03:45 37 ****************** 452 2025-06-29 03:46 38 ******************* 453 2025-06-29 03:47 37 ****************** 454 2025-06-29 03:48 38 ******************* 455 2025-06-29 03:49 37 ****************** ... ..( 16 skipped). .. ****************** 472 2025-06-29 04:06 37 ****************** 473 2025-06-29 04:07 38 ******************* 474 2025-06-29 04:08 37 ****************** ... ..( 6 skipped). .. ****************** 3 2025-06-29 04:15 37 ****************** 4 2025-06-29 04:16 38 ******************* 5 2025-06-29 04:17 37 ****************** 6 2025-06-29 04:18 38 ******************* 7 2025-06-29 04:19 37 ****************** 8 2025-06-29 04:20 38 ******************* 9 2025-06-29 04:21 38 ******************* 10 2025-06-29 04:22 37 ****************** 11 2025-06-29 04:23 37 ****************** 12 2025-06-29 04:24 38 ******************* 13 2025-06-29 04:25 37 ****************** 14 2025-06-29 04:26 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 29 --- Lifetime Power-On Resets 0x01 0x010 4 43237 --- Power-on Hours 0x01 0x018 6 109097320688 --- Logical Sectors Written 0x01 0x020 6 646332446 --- Number of Write Commands 0x01 0x028 6 1482837267651 --- Logical Sectors Read 0x01 0x030 6 2542444840 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 1572 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 43237 --- Spindle Motor Power-on Hours 0x03 0x010 4 43232 --- Head Flying Hours 0x03 0x018 4 86 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 49 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 37 --- Current Temperature 0x05 0x010 1 37 N-- Average Short Term Temperature 0x05 0x018 1 37 N-- Average Long Term Temperature 0x05 0x020 1 48 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x030 1 41 N-- Highest Average Short Term Temperature 0x05 0x038 1 32 N-- Lowest Average Short Term Temperature 0x05 0x040 1 38 N-- Highest Average Long Term Temperature 0x05 0x048 1 34 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 9216 --- Number of Hardware Resets 0x06 0x018 4 3 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 29 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 30 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.31-gentoo] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Ultrastar DC HC550 Device Model: WDC WUH721816ALE6L0 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: PCGNT232 User Capacity: 16,000,900,661,248 bytes [16.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5706 ATA Version is: ACS-4 published, ANSI INCITS 529-2018 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 29 04:26:08 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 242) Self-test routine in progress... 20% of test remaining. Total time to complete Offline data collection: ( 101) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1771) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 001 - 0 2 Throughput_Performance P-S--- 136 136 054 - 96 3 Spin_Up_Time POS--- 084 084 001 - 356 (Average 303) 4 Start_Stop_Count -O--C- 100 100 000 - 21 5 Reallocated_Sector_Ct PO--CK 100 100 001 - 0 7 Seek_Error_Rate PO-R-- 100 100 001 - 0 8 Seek_Time_Performance P-S--- 140 140 020 - 15 9 Power_On_Hours -O--C- 098 098 000 - 14578 10 Spin_Retry_Count PO--C- 100 100 001 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 15 22 Helium_Level PO---K 100 100 025 - 100 192 Power-Off_Retract_Count -O--CK 100 100 000 - 611 193 Load_Cycle_Count -O--C- 100 100 000 - 611 194 Temperature_Celsius -O---- 048 048 000 - 45 (Min/Max 21/51) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 30001 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x2f GPL R/O 1 Sector Configuration log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 14527 - # 2 Short offline Completed without error 00% 14503 - # 3 Short offline Completed without error 00% 14479 - # 4 Short offline Completed without error 00% 14455 - # 5 Short offline Completed without error 00% 14431 - # 6 Extended offline Completed without error 00% 14415 - # 7 Short offline Completed without error 00% 14359 - # 8 Short offline Completed without error 00% 14335 - # 9 Short offline Completed without error 00% 14311 - #10 Short offline Completed without error 00% 14287 - #11 Short offline Completed without error 00% 14263 - #12 Short offline Completed without error 00% 14239 - #13 Extended offline Completed without error 00% 14236 - #14 Short offline Completed without error 00% 14191 - #15 Short offline Completed without error 00% 14167 - #16 Short offline Completed without error 00% 14143 - #17 Short offline Completed without error 00% 14119 - #18 Extended offline Completed without error 00% 14097 - #19 Short offline Completed without error 00% 14023 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: DST executing in background (3) Current Temperature: 45 Celsius Power Cycle Min/Max Temperature: 37/49 Celsius Lifetime Min/Max Temperature: 21/51 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Minimum supported ERC Time Limit: 65 (6.5 seconds) SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (16) Index Estimated Time Temperature Celsius 17 2025-06-29 02:19 45 ************************** ... ..( 20 skipped). .. ************************** 38 2025-06-29 02:40 45 ************************** 39 2025-06-29 02:41 44 ************************* 40 2025-06-29 02:42 45 ************************** 41 2025-06-29 02:43 44 ************************* ... ..( 44 skipped). .. ************************* 86 2025-06-29 03:28 44 ************************* 87 2025-06-29 03:29 45 ************************** 88 2025-06-29 03:30 45 ************************** 89 2025-06-29 03:31 45 ************************** 90 2025-06-29 03:32 44 ************************* ... ..( 28 skipped). .. ************************* 119 2025-06-29 04:01 44 ************************* 120 2025-06-29 04:02 45 ************************** ... ..( 23 skipped). .. ************************** 16 2025-06-29 04:26 45 ************************** SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 15 --- Lifetime Power-On Resets 0x01 0x010 4 14578 --- Power-on Hours 0x01 0x018 6 204479511872 --- Logical Sectors Written 0x01 0x020 6 575249501 --- Number of Write Commands 0x01 0x028 6 866899035636 --- Logical Sectors Read 0x01 0x030 6 3513331414 --- Number of Read Commands 0x01 0x038 6 52484007200 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 14557 --- Spindle Motor Power-on Hours 0x03 0x010 4 14557 --- Head Flying Hours 0x03 0x018 4 611 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 28845 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 45 --- Current Temperature 0x05 0x010 1 44 N-- Average Short Term Temperature 0x05 0x018 1 42 N-- Average Long Term Temperature 0x05 0x020 1 51 --- Highest Temperature 0x05 0x028 1 21 --- Lowest Temperature 0x05 0x030 1 49 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 45 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 79 --- Number of Hardware Resets 0x06 0x010 4 35 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdd smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.31-gentoo] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba P300 (CMR) Device Model: TOSHIBA HDWD130 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MX6OACF0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5706 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 29 04:26:08 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22222) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 371) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 139 139 054 - 72 3 Spin_Up_Time POS--- 253 253 024 - 155 (Average 84) 4 Start_Stop_Count -O--C- 099 099 000 - 5090 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 124 124 020 - 33 9 Power_On_Hours -O--C- 095 095 000 - 40950 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 59 192 Power-Off_Retract_Count -O--CK 095 095 000 - 6563 193 Load_Cycle_Count -O--C- 095 095 000 - 6564 194 Temperature_Celsius -O---- 142 142 000 - 42 (Min/Max 23/51) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 2 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 610 hours (25 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 03 71 00 00 03 e9 4d 8f 03 00 Error: ICRC, ABRT at LBA = 0x03e94d8f = 65621391 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 05 00 00 a0 00 00 03 e9 4c 00 40 08 00:06:52.705 READ FPDMA QUEUED 60 05 00 00 98 00 00 03 e9 47 00 40 08 00:06:52.702 READ FPDMA QUEUED 60 05 00 00 90 00 00 03 e9 42 00 40 08 00:06:52.699 READ FPDMA QUEUED 60 05 00 00 88 00 00 03 e9 3d 00 40 08 00:06:52.696 READ FPDMA QUEUED 60 05 00 00 80 00 00 03 e9 38 00 40 08 00:06:52.693 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 279 hours (11 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 02 a1 00 00 01 69 45 5f 01 00 Error: ICRC, ABRT at LBA = 0x0169455f = 23676255 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 05 00 00 50 00 00 01 69 43 00 40 08 00:09:47.619 READ FPDMA QUEUED 60 05 00 00 48 00 00 01 69 3e 00 40 08 00:09:47.616 READ FPDMA QUEUED 60 05 00 00 40 00 00 01 69 39 00 40 08 00:09:47.613 READ FPDMA QUEUED 60 05 00 00 38 00 00 01 69 34 00 40 08 00:09:47.610 READ FPDMA QUEUED 60 05 00 00 30 00 00 01 69 2f 00 40 08 00:09:47.606 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 40947 - # 2 Short offline Completed without error 00% 40923 - # 3 Extended offline Completed without error 00% 40906 - # 4 Short offline Completed without error 00% 40899 - # 5 Short offline Completed without error 00% 40875 - # 6 Short offline Completed without error 00% 40851 - # 7 Short offline Completed without error 00% 40827 - # 8 Short offline Completed without error 00% 40803 - # 9 Short offline Completed without error 00% 40779 - #10 Short offline Completed without error 00% 40755 - #11 Extended offline Completed without error 00% 40738 - #12 Short offline Completed without error 00% 40731 - #13 Short offline Completed without error 00% 40707 - #14 Short offline Completed without error 00% 40683 - #15 Short offline Completed without error 00% 40659 - #16 Short offline Completed without error 00% 40635 - #17 Short offline Completed without error 00% 40611 - #18 Short offline Completed without error 00% 40587 - #19 Extended offline Completed without error 00% 40570 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 38/48 Celsius Lifetime Min/Max Temperature: 23/51 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (115) Index Estimated Time Temperature Celsius 116 2025-06-29 02:19 42 *********************** ... ..(126 skipped). .. *********************** 115 2025-06-29 04:26 42 *********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 59 --- Lifetime Power-On Resets 0x01 0x010 4 40950 --- Power-on Hours 0x01 0x018 6 35624778176 --- Logical Sectors Written 0x01 0x020 6 72446186 --- Number of Write Commands 0x01 0x028 6 56828860663 --- Logical Sectors Read 0x01 0x030 6 125543859 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 40747 --- Spindle Motor Power-on Hours 0x03 0x010 4 40748 --- Head Flying Hours 0x03 0x018 4 6564 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 10 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 25 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 42 --- Current Temperature 0x05 0x010 1 42 N-- Average Short Term Temperature 0x05 0x018 1 42 N-- Average Long Term Temperature 0x05 0x020 1 51 --- Highest Temperature 0x05 0x028 1 23 --- Lowest Temperature 0x05 0x030 1 47 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 43 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1847 --- Number of Hardware Resets 0x06 0x010 4 1784 --- Number of ASR Events 0x06 0x018 4 2 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sde smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.31-gentoo] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Ultrastar 7K4000 Device Model: Hitachi HUS724030ALE641 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: MJ8OA5F0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5706 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 29 04:26:10 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2], Master PW ID: 0xfffd === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 24) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 1) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 65536 2 Throughput_Performance P-S--- 136 136 054 - 80 3 Spin_Up_Time POS--- 124 124 024 - 619 (Average 626) 4 Start_Stop_Count -O--C- 100 100 000 - 677 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 121 121 020 - 34 9 Power_On_Hours -O--C- 093 093 000 - 54687 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 120 192 Power-Off_Retract_Count -O--CK 098 098 000 - 2704 193 Load_Cycle_Count -O--C- 098 098 000 - 2709 194 Temperature_Celsius -O---- 166 166 000 - 36 (Min/Max 22/56) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 5 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80 GPL R/W 63 Host vendor specific log 0x81-0x9f GPL,SL R/W 16 Host vendor specific log 0xb2 GPL VS 63 Device vendor specific log 0xc8 GPL VS 617 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 5 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [0] occurred at disk power-on lifetime: 2368 hours (98 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 42 00 00 bc 0e 1c 36 0c 00 Error: ICRC, ABRT 66 sectors at LBA = 0xbc0e1c36 = 3155041334 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 d1 00 42 00 00 bc 0e 1c 36 4c ff 2d+23:37:41.358 WRITE DMA EXT 35 00 d1 00 f0 00 00 bc 0e 1b 88 40 00 2d+23:37:41.284 WRITE DMA EXT 35 00 d1 00 10 00 00 bc 0e 1b 78 40 00 2d+23:37:41.283 WRITE DMA EXT 35 00 d1 00 f0 00 00 bc 0e 1a 88 40 00 2d+23:37:41.279 WRITE DMA EXT 35 00 d1 00 10 00 00 bc 0e 1a 78 40 00 2d+23:37:41.279 WRITE DMA EXT Error 4 [3] occurred at disk power-on lifetime: 2368 hours (98 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 58 00 00 b9 af 88 d0 09 00 Error: ICRC, ABRT 88 sectors at LBA = 0xb9af88d0 = 3115288784 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 d1 00 58 00 00 b9 af 88 d0 49 ff 2d+23:25:17.664 WRITE DMA EXT 35 00 d1 00 f0 00 00 b9 af 88 38 40 00 2d+23:25:17.590 WRITE DMA EXT 35 00 d1 00 10 00 00 b9 af 88 28 40 00 2d+23:25:17.589 WRITE DMA EXT 35 00 d1 00 f0 00 00 b9 af 87 38 40 00 2d+23:25:17.585 WRITE DMA EXT 35 00 d1 00 10 00 00 b9 af 87 28 40 00 2d+23:25:17.585 WRITE DMA EXT Error 3 [2] occurred at disk power-on lifetime: 2367 hours (98 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 bd 00 00 ae 67 27 33 0e 00 Error: ICRC, ABRT 189 sectors at LBA = 0xae672733 = 2925995827 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 d1 00 bd 00 00 ae 67 27 33 4e ff 2d+22:28:08.192 WRITE DMA EXT 35 00 d1 00 f0 00 00 ae 67 27 00 40 00 2d+22:28:08.122 WRITE DMA EXT 35 00 d1 00 10 00 00 ae 67 26 f0 40 00 2d+22:28:08.121 WRITE DMA EXT 35 00 d1 00 f0 00 00 ae 67 26 00 40 00 2d+22:28:08.117 WRITE DMA EXT 35 00 d1 00 10 00 00 ae 67 25 f0 40 00 2d+22:28:08.117 WRITE DMA EXT Error 2 [1] occurred at disk power-on lifetime: 2355 hours (98 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 f0 00 00 1d 17 af 00 0d 00 Error: ICRC, ABRT 240 sectors at LBA = 0x1d17af00 = 488091392 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 d1 00 f0 00 00 1d 17 af 00 4d ff 2d+09:57:19.055 WRITE DMA EXT 35 00 d1 00 f0 00 00 1d 17 af 00 40 00 2d+09:57:18.986 WRITE DMA EXT 35 00 d1 00 10 00 00 1d 17 ae f0 40 00 2d+09:57:18.985 WRITE DMA EXT 35 00 d1 00 f0 00 00 1d 17 ae 00 40 00 2d+09:57:18.981 WRITE DMA EXT 35 00 d1 00 10 00 00 1d 17 ad f0 40 00 2d+09:57:18.980 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 54684 - # 2 Short offline Completed without error 00% 54660 - # 3 Extended offline Completed without error 00% 54644 - # 4 Short offline Completed without error 00% 54636 - # 5 Short offline Completed without error 00% 54612 - # 6 Short offline Completed without error 00% 54588 - # 7 Short offline Completed without error 00% 54564 - # 8 Short offline Completed without error 00% 54540 - # 9 Short offline Completed without error 00% 54516 - #10 Short offline Completed without error 00% 54492 - #11 Extended offline Completed without error 00% 54476 - #12 Short offline Completed without error 00% 54468 - #13 Short offline Completed without error 00% 54444 - #14 Short offline Completed without error 00% 54420 - #15 Short offline Completed without error 00% 54396 - #16 Short offline Completed without error 00% 54372 - #17 Short offline Completed without error 00% 54348 - #18 Short offline Completed without error 00% 54324 - #19 Extended offline Completed without error 00% 54308 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 31/40 Celsius Lifetime Min/Max Temperature: 22/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (6) Index Estimated Time Temperature Celsius 7 2025-06-29 02:19 36 ***************** ... ..(126 skipped). .. ***************** 6 2025-06-29 04:26 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 120 --- Lifetime Power-On Resets 0x01 0x018 6 110393896752 --- Logical Sectors Written 0x01 0x020 6 518300000 --- Number of Write Commands 0x01 0x028 6 1174783679604 --- Logical Sectors Read 0x01 0x030 6 2006115767 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 54536 --- Spindle Motor Power-on Hours 0x03 0x010 4 54676 --- Head Flying Hours 0x03 0x018 4 2709 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 1409 --- Read Recovery Attempts 0x03 0x030 4 4 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 17 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 36 --- Current Temperature 0x05 0x010 1 36 N-- Average Short Term Temperature 0x05 0x018 1 35 N-- Average Long Term Temperature 0x05 0x020 1 56 --- Highest Temperature 0x05 0x028 1 22 --- Lowest Temperature 0x05 0x030 1 51 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 48 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1330 --- Number of Hardware Resets 0x06 0x010 4 1094 --- Number of ASR Events 0x06 0x018 4 5 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 29 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 30 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdf smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.31-gentoo] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Exos X14 Device Model: ST12000NM0008-2H3101 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: SN03 User Capacity: 12,000,138,625,024 bytes [12.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5706 ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 29 04:26:12 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 575) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: (1176) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 064 044 - 422392 3 Spin_Up_Time PO---- 090 090 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 32 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 090 060 045 - 935391828 9 Power_On_Hours -O--CK 055 055 000 - 40185 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 32 18 Head_Health PO-R-- 100 100 050 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 099 000 - 38655295497 190 Airflow_Temperature_Cel -O---K 065 049 040 - 35 (Min/Max 29/40) 192 Power-Off_Retract_Count -O--CK 100 100 000 - 20 193 Load_Cycle_Count -O--CK 090 090 000 - 21208 194 Temperature_Celsius -O---K 035 042 000 - 35 (0 21 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 100 001 000 - 422392 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Pressure_Limit PO---K 100 100 001 - 0 240 Head_Flying_Hours ------ 100 253 000 - 38806h+54m+40.760s 241 Total_LBAs_Written ------ 100 253 000 - 186405039520 242 Total_LBAs_Read ------ 100 253 000 - 3805636288078 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 8 Device Statistics Notification 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 768 Current Device Internal Status Data log 0x2f GPL R/O 1 Sector Configuration log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 24 Device vendor specific log 0xa2 GPL VS 16320 Device vendor specific log 0xa4 GPL,SL VS 160 Device vendor specific log 0xa6 GPL VS 192 Device vendor specific log 0xa8-0xa9 GPL,SL VS 136 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xad GPL VS 16 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 8 Device vendor specific log 0xc3 GPL,SL VS 32 Device vendor specific log 0xc9 GPL,SL VS 8 Device vendor specific log 0xca GPL,SL VS 16 Device vendor specific log 0xd1 GPL VS 336 Device vendor specific log 0xd2 GPL VS 10000 Device vendor specific log 0xd4 GPL VS 2048 Device vendor specific log 0xda GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 40182 - # 2 Short offline Completed without error 00% 40158 - # 3 Extended offline Completed without error 00% 40154 - # 4 Short offline Completed without error 00% 40134 - # 5 Short offline Completed without error 00% 40110 - # 6 Short offline Completed without error 00% 40086 - # 7 Short offline Completed without error 00% 40062 - # 8 Short offline Completed without error 00% 40038 - # 9 Short offline Completed without error 00% 40014 - #10 Short offline Completed without error 00% 39990 - #11 Extended offline Completed without error 00% 39985 - #12 Short offline Completed without error 00% 39966 - #13 Short offline Completed without error 00% 39942 - #14 Short offline Completed without error 00% 39918 - #15 Short offline Completed without error 00% 39894 - #16 Short offline Completed without error 00% 39870 - #17 Short offline Completed without error 00% 39846 - #18 Short offline Completed without error 00% 39822 - #19 Extended offline Completed without error 00% 39817 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 29/40 Celsius Lifetime Min/Max Temperature: 21/51 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Vendor specific: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 3 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 10/40 Celsius Min/Max Temperature Limit: 5/60 Celsius Temperature History Size (Index): 128 (50) Index Estimated Time Temperature Celsius 51 2025-06-23 23:28 36 ***************** 52 2025-06-24 00:27 36 ***************** 53 2025-06-24 01:26 35 **************** ... ..( 7 skipped). .. **************** 61 2025-06-24 09:18 35 **************** 62 2025-06-24 10:17 34 *************** 63 2025-06-24 11:16 34 *************** 64 2025-06-24 12:15 35 **************** ... ..( 17 skipped). .. **************** 82 2025-06-25 05:57 35 **************** 83 2025-06-25 06:56 34 *************** 84 2025-06-25 07:55 34 *************** 85 2025-06-25 08:54 35 **************** ... ..( 3 skipped). .. **************** 89 2025-06-25 12:50 35 **************** 90 2025-06-25 13:49 36 ***************** ... ..( 9 skipped). .. ***************** 100 2025-06-25 23:39 36 ***************** 101 2025-06-26 00:38 35 **************** 102 2025-06-26 01:37 35 **************** 103 2025-06-26 02:36 36 ***************** 104 2025-06-26 03:35 35 **************** ... ..( 7 skipped). .. **************** 112 2025-06-26 11:27 35 **************** 113 2025-06-26 12:26 36 ***************** 114 2025-06-26 13:25 35 **************** 115 2025-06-26 14:24 36 ***************** 116 2025-06-26 15:23 36 ***************** 117 2025-06-26 16:22 37 ****************** 118 2025-06-26 17:21 37 ****************** 119 2025-06-26 18:20 37 ****************** 120 2025-06-26 19:19 36 ***************** ... ..( 6 skipped). .. ***************** 127 2025-06-27 02:12 36 ***************** 0 2025-06-27 03:11 39 ******************** 1 2025-06-27 04:10 40 ********************* ... ..( 2 skipped). .. ********************* 4 2025-06-27 07:07 40 ********************* 5 2025-06-27 08:06 39 ******************** 6 2025-06-27 09:05 39 ******************** 7 2025-06-27 10:04 39 ******************** 8 2025-06-27 11:03 38 ******************* ... ..( 2 skipped). .. ******************* 11 2025-06-27 14:00 38 ******************* 12 2025-06-27 14:59 39 ******************** ... ..( 2 skipped). .. ******************** 15 2025-06-27 17:56 39 ******************** 16 2025-06-27 18:55 37 ****************** 17 2025-06-27 19:54 38 ******************* 18 2025-06-27 20:53 38 ******************* 19 2025-06-27 21:52 38 ******************* 20 2025-06-27 22:51 36 ***************** 21 2025-06-27 23:50 36 ***************** 22 2025-06-28 00:49 36 ***************** 23 2025-06-28 01:48 35 **************** 24 2025-06-28 02:47 36 ***************** 25 2025-06-28 03:46 35 **************** ... ..( 9 skipped). .. **************** 35 2025-06-28 13:36 35 **************** 36 2025-06-28 14:35 36 ***************** ... ..( 5 skipped). .. ***************** 42 2025-06-28 20:29 36 ***************** 43 2025-06-28 21:28 35 **************** 44 2025-06-28 22:27 36 ***************** 45 2025-06-28 23:26 35 **************** ... ..( 4 skipped). .. **************** 50 2025-06-29 04:21 35 **************** SCT Error Recovery Control: Read: 100 (10.0 seconds) Write: 100 (10.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 32 --- Lifetime Power-On Resets 0x01 0x010 4 40185 --- Power-on Hours 0x01 0x018 6 186402277768 --- Logical Sectors Written 0x01 0x020 6 1288426840 --- Number of Write Commands 0x01 0x028 6 3805363506985 --- Logical Sectors Read 0x01 0x030 6 6231331205 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 40180 --- Spindle Motor Power-on Hours 0x03 0x010 4 39737 --- Head Flying Hours 0x03 0x018 4 21208 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 20 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 9 --- Resets Between Cmd Acceptance and Completion 0x04 0x018 4 0 -D- Physical Element Status Changed 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 --- Current Temperature 0x05 0x010 1 35 --- Average Short Term Temperature 0x05 0x018 1 35 --- Average Long Term Temperature 0x05 0x020 1 42 --- Highest Temperature 0x05 0x028 1 29 --- Lowest Temperature 0x05 0x030 1 39 --- Highest Average Short Term Temperature 0x05 0x038 1 30 --- Lowest Average Short Term Temperature 0x05 0x040 1 35 --- Highest Average Long Term Temperature 0x05 0x048 1 32 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 642 --- Number of Hardware Resets 0x06 0x010 4 240 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == 0xff 0x008 7 0 --- Vendor Specific 0xff 0x010 7 6 --- Vendor Specific 0xff 0x018 7 0 --- Vendor Specific |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 30 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS Seagate FARM log (GP Log 0xa6) supported [try: -l farm] /dev/sdg smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.31-gentoo] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SSDPR-CL100-480-G2 Serial Number: -- LU WWN Device Id: 5 02b2a2 ... Add. Product Id: mavlsata Firmware Version: R1029A User Capacity: 480,103,981,056 bytes [480 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: Not in smartctl database 7.3/5706 ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 29 04:26:12 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x35) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x00) Error logging NOT supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 1) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 5 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours PO--CK 100 100 010 - 52451 12 Power_Cycle_Count PO--CK 100 100 010 - 113 161 Unknown_Attribute PO--CK 100 100 010 - 0 164 Unknown_Attribute PO--CK 100 100 010 - 2154678 165 Unknown_Attribute PO--CK 100 100 010 - 3161 166 Unknown_Attribute PO--CK 100 100 010 - 0 167 Unknown_Attribute PO--CK 100 100 010 - 3127 169 Unknown_Attribute PO--CK 100 100 010 - 0 176 Erase_Fail_Count_Chip PO--CK 100 100 010 - 0 177 Wear_Leveling_Count PO--CK 100 100 010 - 0 178 Used_Rsvd_Blk_Cnt_Chip PO--CK 100 100 010 - 0 192 Power-Off_Retract_Count PO--CK 100 100 010 - 0 194 Temperature_Celsius PO--CK 100 100 010 - 45 195 Hardware_ECC_Recovered PO--CK 100 100 010 - 0 199 UDMA_CRC_Error_Count PO--CK 100 100 010 - 0 241 Total_LBAs_Written PO--CK 100 100 010 - 782146 242 Total_LBAs_Read PO--CK 100 100 010 - 75284 243 Unknown_Attribute PO--CK 100 100 010 - 0 244 Unknown_Attribute PO--CK 100 100 010 - 0 245 Unknown_Attribute PO--CK 100 100 010 - 0 246 Unknown_Attribute PO--CK 100 100 010 - 0 248 Unknown_Attribute PO--CK 100 100 010 - 0 250 Read_Error_Retry_Rate PO--CK 100 100 010 - 0 251 Unknown_Attribute PO--CK 100 100 010 - 0 252 Unknown_Attribute PO--CK 100 100 010 - 0 253 Unknown_Attribute PO--CK 100 100 010 - 0 254 Unknown_SSD_Attribute PO--CK 100 100 010 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x10 GPL,SL R/O 1 NCQ Command Error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported Read SMART Error Log failed: scsi error badly formed scsi parameters SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test Log not supported Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdh smartctl 7.5 2025-04-30 r5714 [x86_64-linux-6.12.31-gentoo] (local build) Copyright (C) 2002-25, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Ultrastar 7K4000 Device Model: Hitachi HUS724030ALE641 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: MJ8OA5F0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5706 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Jun 29 04:26:12 2025 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2], Master PW ID: 0xfffd === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 24) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 1) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 136 136 054 - 80 3 Spin_Up_Time POS--- 130 130 024 - 457 (Average 501) 4 Start_Stop_Count -O--C- 100 100 000 - 171 5 Reallocated_Sector_Ct PO--CK 073 073 005 - 670 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 119 119 020 - 35 9 Power_On_Hours -O--C- 092 092 000 - 61369 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 170 192 Power-Off_Retract_Count -O--CK 096 096 000 - 5237 193 Load_Cycle_Count -O--C- 096 096 000 - 5237 194 Temperature_Celsius -O---- 146 146 000 - 41 (Min/Max 21/54) 196 Reallocated_Event_Count -O--CK 072 072 000 - 690 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 4 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80 GPL R/W 63 Host vendor specific log 0x81-0x9f GPL,SL R/W 16 Host vendor specific log 0xb2 GPL VS 63 Device vendor specific log 0xc8 GPL VS 617 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 4 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4 [3] occurred at disk power-on lifetime: 10008 hours (417 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 e1 00 00 72 24 6a 1f 02 00 Error: ICRC, ABRT at LBA = 0x72246a1f = 1914989087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 02 00 00 98 00 00 72 24 7e 00 40 00 00:00:20.901 READ FPDMA QUEUED 60 04 00 00 90 00 00 72 24 7a 00 40 00 00:00:20.901 READ FPDMA QUEUED 60 01 00 00 88 00 00 72 24 79 00 40 00 00:00:20.901 READ FPDMA QUEUED 60 03 00 00 80 00 00 72 24 76 00 40 00 00:00:20.901 READ FPDMA QUEUED 60 03 00 00 78 00 00 72 24 73 00 40 00 00:00:20.900 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 10008 hours (417 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 e1 00 00 72 1f c0 1f 02 00 Error: ICRC, ABRT at LBA = 0x721fc01f = 1914683423 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 70 6a 58 18 40 00 00:00:04.113 READ FPDMA QUEUED 60 00 08 00 e8 00 00 70 6a 57 18 40 00 00:00:04.113 READ FPDMA QUEUED 60 01 00 00 e0 00 00 72 1f c4 00 40 00 00:00:04.112 READ FPDMA QUEUED 60 01 00 00 d8 00 00 72 1f c3 00 40 00 00:00:04.112 READ FPDMA QUEUED 60 01 00 00 d0 00 00 72 1f c2 00 40 00 00:00:04.112 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 79 hours (3 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 70 00 00 71 8b 13 90 01 00 Error: ICRC, ABRT at LBA = 0x718b1390 = 1904939920 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 0a 00 00 d8 00 00 71 8b 96 00 40 08 10:51:49.066 WRITE FPDMA QUEUED 61 0a 00 00 d0 00 00 71 8b 8c 00 40 08 10:51:49.066 WRITE FPDMA QUEUED 61 0a 00 00 c8 00 00 71 8b 82 00 40 08 10:51:49.066 WRITE FPDMA QUEUED 61 0a 00 00 c0 00 00 71 8b 78 00 40 08 10:51:49.066 WRITE FPDMA QUEUED 61 0a 00 00 b8 00 00 71 8b 6e 00 40 08 10:51:49.066 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 1 hours (0 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 02 80 00 00 00 41 44 80 00 00 Error: ICRC, ABRT at LBA = 0x00414480 = 4277376 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 06 00 00 c0 00 00 00 41 7f 80 40 08 00:08:38.869 WRITE FPDMA QUEUED 61 08 80 00 b8 00 00 00 41 77 00 40 08 00:08:38.862 WRITE FPDMA QUEUED 61 09 00 00 b0 00 00 00 41 6e 00 40 08 00:08:38.855 WRITE FPDMA QUEUED 61 09 00 00 a8 00 00 00 41 65 00 40 08 00:08:38.848 WRITE FPDMA QUEUED 61 05 00 00 a0 00 00 00 41 60 00 40 08 00:08:38.833 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 61366 - # 2 Short offline Completed without error 00% 61342 - # 3 Extended offline Completed without error 00% 61326 - # 4 Short offline Completed without error 00% 61318 - # 5 Short offline Completed without error 00% 61294 - # 6 Short offline Completed without error 00% 61270 - # 7 Short offline Completed without error 00% 61246 - # 8 Short offline Completed without error 00% 61222 - # 9 Short offline Completed without error 00% 61198 - #10 Short offline Completed without error 00% 61174 - #11 Extended offline Completed without error 00% 61158 - #12 Short offline Completed without error 00% 61150 - #13 Short offline Completed without error 00% 61126 - #14 Short offline Completed without error 00% 61102 - #15 Short offline Completed without error 00% 61078 - #16 Short offline Completed without error 00% 61054 - #17 Short offline Completed without error 00% 61030 - #18 Short offline Completed without error 00% 61006 - #19 Extended offline Completed without error 00% 60990 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 37/47 Celsius Lifetime Min/Max Temperature: 21/54 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (75) Index Estimated Time Temperature Celsius 76 2025-06-29 02:19 41 ********************** ... ..( 95 skipped). .. ********************** 44 2025-06-29 03:55 41 ********************** 45 2025-06-29 03:56 42 *********************** 46 2025-06-29 03:57 41 ********************** ... ..( 28 skipped). .. ********************** 75 2025-06-29 04:26 41 ********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 170 --- Lifetime Power-On Resets 0x01 0x018 6 144711441624 --- Logical Sectors Written 0x01 0x020 6 872297406 --- Number of Write Commands 0x01 0x028 6 1450605058924 --- Logical Sectors Read 0x01 0x030 6 2905976317 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 61358 --- Spindle Motor Power-on Hours 0x03 0x010 4 61358 --- Head Flying Hours 0x03 0x018 4 5237 --- Head Load Events 0x03 0x020 4 670 --- Number of Reallocated Logical Sectors 0x03 0x028 4 3298 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 11 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 42 --- Current Temperature 0x05 0x010 1 41 N-- Average Short Term Temperature 0x05 0x018 1 41 N-- Average Long Term Temperature 0x05 0x020 1 54 --- Highest Temperature 0x05 0x028 1 21 --- Lowest Temperature 0x05 0x030 1 50 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 44 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1893 --- Number of Hardware Resets 0x06 0x010 4 1342 --- Number of ASR Events 0x06 0x018 4 4 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 23 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 22 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS


Hardware for Linux and BSD

GitHub