/dev/sda smartctl 7.3 2022-02-28 r5338 [i686-linux-6.1.0-10-686-pae] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD3200BEVT-00A0RT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jul 16 02:09:14 2023 -04 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 102) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 188 184 021 - 1591 4 Start_Stop_Count -O--CK 094 094 000 - 6644 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 2 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 085 085 000 - 11071 10 Spin_Retry_Count -O--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 6623 192 Power-Off_Retract_Count -O--CK 198 198 000 - 1786 193 Load_Cycle_Count -O--CK 196 196 000 - 14812 194 Temperature_Celsius -O---K 103 086 000 - 44 196 Reallocated_Event_Count -O--CK 199 199 000 - 1 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 17 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 17 [16] occurred at disk power-on lifetime: 449 hours (18 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 05 4e a2 f2 e0 00 Error: UNC 8 sectors at LBA = 0x054ea2f2 = 89039602 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 05 4e a2 f0 e0 00 00:38:00.928 READ DMA EXT 35 00 00 00 08 00 00 02 67 92 48 e0 00 00:38:00.927 WRITE DMA EXT 25 00 00 00 e0 00 00 05 4e a5 b8 e0 00 00:38:00.926 READ DMA EXT 25 00 00 01 00 00 00 05 4e a4 b8 e0 00 00:38:00.917 READ DMA EXT 25 00 00 01 00 00 00 05 4e a3 b8 e0 00 00:38:00.916 READ DMA EXT Error 16 [15] occurred at disk power-on lifetime: 449 hours (18 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 05 4e a2 f2 e0 00 Error: UNC 8 sectors at LBA = 0x054ea2f2 = 89039602 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 05 4e a2 f0 e0 00 00:37:58.629 READ DMA EXT 25 00 00 00 40 00 00 05 4e a3 78 e0 00 00:37:58.629 READ DMA EXT 25 00 00 00 08 00 00 05 4e a2 f0 e0 00 00:37:56.338 READ DMA EXT 25 00 00 00 80 00 00 05 4e a2 f8 e0 00 00:37:56.332 READ DMA EXT 25 00 00 00 08 00 00 05 4e a2 e8 e0 00 00:37:56.332 READ DMA EXT Error 15 [14] occurred at disk power-on lifetime: 449 hours (18 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 05 4e a2 f2 e0 00 Error: UNC 8 sectors at LBA = 0x054ea2f2 = 89039602 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 05 4e a2 f0 e0 00 00:37:56.338 READ DMA EXT 25 00 00 00 80 00 00 05 4e a2 f8 e0 00 00:37:56.332 READ DMA EXT 25 00 00 00 08 00 00 05 4e a2 e8 e0 00 00:37:56.332 READ DMA EXT 35 00 00 00 08 00 00 02 93 3c f0 e0 00 00:37:56.331 WRITE DMA EXT 35 00 00 00 08 00 00 02 8e bc e0 e0 00 00:37:56.331 WRITE DMA EXT Error 14 [13] occurred at disk power-on lifetime: 449 hours (18 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 05 4e a2 f2 e0 00 Error: UNC 128 sectors at LBA = 0x054ea2f2 = 89039602 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 05 4e a2 f0 e0 00 00:37:54.046 READ DMA EXT 25 00 00 00 08 00 00 05 4e a2 e0 e0 00 00:37:54.046 READ DMA EXT 35 00 00 00 08 00 00 02 92 f2 a8 e0 00 00:37:54.045 WRITE DMA EXT 35 00 00 00 08 00 00 02 8e bc f0 e0 00 00:37:54.045 WRITE DMA EXT 35 00 00 00 08 00 00 02 4c a0 90 e0 00 00:37:54.045 WRITE DMA EXT Error 13 [12] occurred at disk power-on lifetime: 449 hours (18 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 05 4e a2 f2 e0 00 Error: UNC 128 sectors at LBA = 0x054ea2f2 = 89039602 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 05 4e a2 e8 e0 00 00:37:51.759 READ DMA EXT 25 00 00 00 08 00 00 05 4e a2 d8 e0 00 00:37:51.759 READ DMA EXT 35 00 00 00 08 00 00 02 a4 47 78 e0 00 00:37:51.759 WRITE DMA EXT 35 00 00 00 08 00 00 02 81 33 48 e0 00 00:37:51.759 WRITE DMA EXT 35 00 00 00 08 00 00 02 4b 02 20 e0 00 00:37:51.758 WRITE DMA EXT Error 12 [11] occurred at disk power-on lifetime: 449 hours (18 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 05 4e a2 f2 e0 00 Error: UNC 128 sectors at LBA = 0x054ea2f2 = 89039602 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 05 4e a2 e0 e0 00 00:37:49.473 READ DMA EXT 25 00 00 00 08 00 00 05 4e a2 d0 e0 00 00:37:49.473 READ DMA EXT 35 00 00 00 10 00 00 02 8f 63 28 e0 00 00:37:49.473 WRITE DMA EXT 35 00 00 00 08 00 00 02 4b 03 58 e0 00 00:37:49.473 WRITE DMA EXT 35 00 00 00 08 00 00 02 33 3b 70 e0 00 00:37:49.472 WRITE DMA EXT Error 11 [10] occurred at disk power-on lifetime: 449 hours (18 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 05 4e a2 f2 e0 00 Error: UNC 128 sectors at LBA = 0x054ea2f2 = 89039602 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 05 4e a2 d8 e0 00 00:37:47.180 READ DMA EXT 25 00 00 00 08 00 00 05 4e a2 c8 e0 00 00:37:47.180 READ DMA EXT 25 00 00 00 20 00 00 02 92 f2 a0 e0 00 00:37:47.163 READ DMA EXT 35 00 00 00 08 00 00 02 4b 03 38 e0 00 00:37:47.163 WRITE DMA EXT 35 00 00 00 08 00 00 02 33 3b 78 e0 00 00:37:47.163 WRITE DMA EXT Error 10 [9] occurred at disk power-on lifetime: 449 hours (18 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 05 4e a2 f2 e0 00 Error: UNC 128 sectors at LBA = 0x054ea2f2 = 89039602 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 05 4e a2 d0 e0 00 00:37:44.877 READ DMA EXT 25 00 00 00 08 00 00 05 4e a2 c0 e0 00 00:37:44.877 READ DMA EXT 35 00 00 00 08 00 00 02 94 fd 78 e0 00 00:37:44.876 WRITE DMA EXT 35 00 00 00 08 00 00 02 53 fb a0 e0 00 00:37:44.876 WRITE DMA EXT 35 00 00 00 08 00 00 02 4b 02 e0 e0 00 00:37:44.876 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 44 Celsius Power Cycle Min/Max Temperature: 31/45 Celsius Lifetime Min/Max Temperature: 33/61 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (66) Index Estimated Time Temperature Celsius 67 2023-07-16 00:02 43 ************************ 68 2023-07-16 00:03 42 *********************** ... ..( 12 skipped). .. *********************** 81 2023-07-16 00:16 42 *********************** 82 2023-07-16 00:17 43 ************************ 83 2023-07-16 00:18 42 *********************** 84 2023-07-16 00:19 42 *********************** 85 2023-07-16 00:20 43 ************************ 86 2023-07-16 00:21 42 *********************** ... ..( 7 skipped). .. *********************** 94 2023-07-16 00:29 42 *********************** 95 2023-07-16 00:30 43 ************************ 96 2023-07-16 00:31 42 *********************** 97 2023-07-16 00:32 43 ************************ 98 2023-07-16 00:33 43 ************************ 99 2023-07-16 00:34 42 *********************** ... ..( 4 skipped). .. *********************** 104 2023-07-16 00:39 42 *********************** 105 2023-07-16 00:40 43 ************************ 106 2023-07-16 00:41 43 ************************ 107 2023-07-16 00:42 43 ************************ 108 2023-07-16 00:43 42 *********************** 109 2023-07-16 00:44 43 ************************ 110 2023-07-16 00:45 43 ************************ 111 2023-07-16 00:46 43 ************************ 112 2023-07-16 00:47 42 *********************** 113 2023-07-16 00:48 42 *********************** 114 2023-07-16 00:49 43 ************************ ... ..( 18 skipped). .. ************************ 5 2023-07-16 01:08 43 ************************ 6 2023-07-16 01:09 44 ************************* 7 2023-07-16 01:10 43 ************************ 8 2023-07-16 01:11 43 ************************ 9 2023-07-16 01:12 44 ************************* ... ..( 14 skipped). .. ************************* 24 2023-07-16 01:27 44 ************************* 25 2023-07-16 01:28 45 ************************** ... ..( 5 skipped). .. ************************** 31 2023-07-16 01:34 45 ************************** 32 2023-07-16 01:35 44 ************************* 33 2023-07-16 01:36 45 ************************** 34 2023-07-16 01:37 44 ************************* 35 2023-07-16 01:38 44 ************************* 36 2023-07-16 01:39 45 ************************** 37 2023-07-16 01:40 44 ************************* 38 2023-07-16 01:41 44 ************************* 39 2023-07-16 01:42 44 ************************* 40 2023-07-16 01:43 45 ************************** ... ..( 6 skipped). .. ************************** 47 2023-07-16 01:50 45 ************************** 48 2023-07-16 01:51 44 ************************* ... ..( 17 skipped). .. ************************* 66 2023-07-16 02:09 44 ************************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 32144 Vendor specific