/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3750640AS Serial Number: -- Firmware Version: 3.AAK User Capacity: 750 155 292 160 bytes [750 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sun Nov 27 01:03:35 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 39) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 202) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 105 088 006 - 34665538 3 Spin_Up_Time PO---- 099 092 000 - 0 4 Start_Stop_Count -O--CK 093 093 020 - 7630 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 087 060 030 - 557985160 9 Power_On_Hours -O--CK 052 052 000 - 42180 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 094 094 020 - 6738 187 Reported_Uncorrect -O--CK 001 001 000 - 195 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 058 028 045 Past 42 (Min/Max 25/44 #9628) 194 Temperature_Celsius -O---K 042 072 000 - 42 (0 17 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 063 054 000 - 96072461 197 Current_Pending_Sector -O--C- 100 100 000 - 1 198 Offline_Uncorrectable ----C- 100 100 000 - 1 199 UDMA_CRC_Error_Count -OSRCK 200 195 000 - 181 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 213 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 213 [12] occurred at disk power-on lifetime: 18514 hours (771 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 0f ed 44 bc 44 e0 00 Error: UNC at LBA = 0xfed44bc44 = 68405214276 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 0f ed 00 bc 3f e0 00 05:54:08.699 READ DMA EXT 35 00 00 00 08 00 00 26 00 00 8f e0 00 05:54:08.699 WRITE DMA EXT 35 00 00 00 08 00 00 bf 00 00 c7 e0 00 05:54:08.698 WRITE DMA EXT 35 00 00 00 08 00 00 26 00 00 7f e0 00 05:54:08.181 WRITE DMA EXT 35 00 00 00 08 00 1b ff 00 0d bf e0 00 05:54:08.181 WRITE DMA EXT Error 212 [11] occurred at disk power-on lifetime: 18601 hours (775 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 0f ed 44 bc 44 e0 00 Error: UNC at LBA = 0xfed44bc44 = 68405214276 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 0f ed 00 bc 3f e0 00 04:10:29.571 READ DMA EXT 35 00 00 00 08 00 00 00 00 5e 47 e0 00 04:10:29.562 WRITE DMA EXT 25 00 00 00 20 00 0f ed 00 bc 3f e0 00 04:10:29.561 READ DMA EXT 35 00 00 00 08 00 0f 89 00 9e 37 e0 00 04:10:29.561 WRITE DMA EXT 25 00 00 00 40 00 07 ae 00 d3 9f e0 00 04:10:29.560 READ DMA EXT Error 211 [10] occurred at disk power-on lifetime: 18601 hours (775 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 0f ed 44 bc 44 e0 00 Error: UNC at LBA = 0xfed44bc44 = 68405214276 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 0f ed 00 bc 3f e0 00 04:10:29.571 READ DMA EXT 35 00 00 00 08 00 0f 89 00 9e 37 e0 00 04:10:29.562 WRITE DMA EXT 25 00 00 00 40 00 07 ae 00 d3 9f e0 00 04:10:29.561 READ DMA EXT 25 00 00 00 40 00 07 ae 00 d3 5f e0 00 04:10:29.561 READ DMA EXT 35 00 00 00 08 00 00 00 00 5e 3f e0 00 04:10:29.560 WRITE DMA EXT Error 210 [9] occurred at disk power-on lifetime: 18514 hours (771 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 0f ed 44 bc 44 e0 00 Error: UNC at LBA = 0xfed44bc44 = 68405214276 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 0f ed 00 bc 3f e0 00 05:54:08.699 READ DMA EXT 35 00 00 00 20 00 00 c6 00 5f df e0 00 05:54:08.699 WRITE DMA EXT 25 00 00 00 38 00 00 dc 00 2d 51 e0 00 05:54:08.698 READ DMA EXT 25 00 00 00 20 00 0f ed 00 bc 3f e0 00 05:54:08.181 READ DMA EXT 35 00 00 00 08 00 00 26 00 00 8f e0 00 05:54:08.181 WRITE DMA EXT Error 209 [8] occurred at disk power-on lifetime: 18514 hours (771 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 0f ed 44 bc 44 e0 00 Error: UNC at LBA = 0xfed44bc44 = 68405214276 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 0f ed 00 bc 3f e0 00 05:54:08.699 READ DMA EXT 35 00 00 00 08 00 00 26 00 00 8f e0 00 05:54:08.699 WRITE DMA EXT 35 00 00 00 08 00 00 bf 00 00 c7 e0 00 05:54:08.698 WRITE DMA EXT 35 00 00 00 08 00 00 26 00 00 7f e0 00 05:54:08.181 WRITE DMA EXT 35 00 00 00 08 00 1b ff 00 0d bf e0 00 05:54:08.181 WRITE DMA EXT Error 208 [7] occurred at disk power-on lifetime: 18601 hours (775 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 0f ed 44 bc 44 e0 00 Error: UNC at LBA = 0xfed44bc44 = 68405214276 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 0f ed 00 bc 3f e0 00 04:10:29.571 READ DMA EXT 35 00 00 00 08 00 00 00 00 5e 47 e0 00 04:10:29.562 WRITE DMA EXT 25 00 00 00 20 00 0f ed 00 bc 3f e0 00 04:10:29.561 READ DMA EXT 35 00 00 00 08 00 0f 89 00 9e 37 e0 00 04:10:29.561 WRITE DMA EXT 25 00 00 00 40 00 07 ae 00 d3 9f e0 00 04:10:29.560 READ DMA EXT Error 207 [6] occurred at disk power-on lifetime: 18601 hours (775 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 0f ed 44 bc 44 e0 00 Error: UNC at LBA = 0xfed44bc44 = 68405214276 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 20 00 0f ed 00 bc 3f e0 00 04:10:29.571 READ DMA EXT 35 00 00 00 08 00 0f 89 00 9e 37 e0 00 04:10:29.562 WRITE DMA EXT 25 00 00 00 40 00 07 ae 00 d3 9f e0 00 04:10:29.561 READ DMA EXT 25 00 00 00 40 00 07 ae 00 d3 5f e0 00 04:10:29.561 READ DMA EXT 35 00 00 00 08 00 00 00 00 5e 3f e0 00 04:10:29.560 WRITE DMA EXT Error 206 [5] occurred at disk power-on lifetime: 18514 hours (771 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 0f ed 44 bc 44 e0 00 Error: UNC at LBA = 0xfed44bc44 = 68405214276 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 0f ed 00 bc 3f e0 00 05:54:08.699 READ DMA EXT 35 00 00 00 20 00 00 c6 00 5f df e0 00 05:54:08.699 WRITE DMA EXT 25 00 00 00 38 00 00 dc 00 2d 51 e0 00 05:54:08.698 READ DMA EXT 25 00 00 00 20 00 0f ed 00 bc 3f e0 00 05:54:08.181 READ DMA EXT 35 00 00 00 08 00 00 26 00 00 8f e0 00 05:54:08.181 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Vendor (0x50) Fatal or unknown error 00% 29810 51805895524352 # 2 Vendor (0x50) Fatal or unknown error 00% 29810 51805895524352 # 3 Vendor (0x50) Fatal or unknown error 00% 29810 51805895524352 # 4 Vendor (0x50) Fatal or unknown error 00% 29810 51805895524352 # 5 Vendor (0x50) Fatal or unknown error 00% 29810 51805895524352 # 6 Vendor (0x50) Fatal or unknown error 00% 29810 51805895524352 # 7 Short offline Completed without error 00% 29810 - # 8 Extended offline Self-test routine in progress 70% 41675 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 13 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-08M2NA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Nov 27 01:03:35 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12000) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 124) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 191 174 021 - 1441 4 Start_Stop_Count -O--CK 100 100 000 - 675 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 083 083 000 - 12485 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 536 192 Power-Off_Retract_Count -O--CK 200 200 000 - 276 193 Load_Cycle_Count -O--CK 200 200 000 - 451 194 Temperature_Celsius -O---K 110 098 000 - 33 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Interrupted (host reset) 50% 11979 - # 2 Vendor (0x50) Completed without error 00% 29 - # 3 Short offline Completed without error 00% 29 - # 4 Vendor (0x50) Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 24/34 Celsius Lifetime Min/Max Temperature: 18/45 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (309) Index Estimated Time Temperature Celsius 310 2016-11-26 17:06 33 ************** ... ..( 97 skipped). .. ************** 408 2016-11-26 18:44 33 ************** 409 2016-11-26 18:45 34 *************** ... ..( 5 skipped). .. *************** 415 2016-11-26 18:51 34 *************** 416 2016-11-26 18:52 33 ************** ... ..( 10 skipped). .. ************** 427 2016-11-26 19:03 33 ************** 428 2016-11-26 19:04 34 *************** ... ..( 27 skipped). .. *************** 456 2016-11-26 19:32 34 *************** 457 2016-11-26 19:33 33 ************** ... ..( 40 skipped). .. ************** 20 2016-11-26 20:14 33 ************** 21 2016-11-26 20:15 34 *************** ... ..( 12 skipped). .. *************** 34 2016-11-26 20:28 34 *************** 35 2016-11-26 20:29 33 ************** ... ..( 9 skipped). .. ************** 45 2016-11-26 20:39 33 ************** 46 2016-11-26 20:40 32 ************* ... ..(150 skipped). .. ************* 197 2016-11-26 23:11 32 ************* 198 2016-11-26 23:12 33 ************** ... ..(110 skipped). .. ************** 309 2016-11-27 01:03 33 ************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 19 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 352555 Vendor specific