/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.19.0-desktop-13.1rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 750 EVO 250GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: MAT01B6Q User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Apr 29 15:07:28 2020 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 133) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 096 096 000 - 16274 12 Power_Cycle_Count -O--CK 098 098 000 - 1716 177 Wear_Leveling_Count PO--C- 062 062 000 - 189 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 066 041 000 - 34 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 373 241 Total_LBAs_Written -O--CK 099 099 000 - 78027860336 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 16059 - # 2 Extended offline Aborted by host 80% 15831 - # 3 Extended offline Completed without error 00% 15714 - # 4 Extended offline Interrupted (host reset) 90% 15371 - # 5 Extended offline Completed without error 00% 15239 - # 6 Extended offline Completed without error 00% 14851 - # 7 Extended offline Completed without error 00% 14463 - # 8 Extended offline Aborted by host 70% 14216 - # 9 Extended offline Completed without error 00% 13188 - #10 Extended offline Completed without error 00% 12851 - #11 Extended offline Completed without error 00% 12592 - #12 Extended offline Aborted by host 70% 12013 - #13 Extended offline Completed without error 00% 11770 - #14 Extended offline Completed without error 00% 11427 - #15 Extended offline Completed without error 00% 11310 - #16 Extended offline Completed without error 00% 10970 - #17 Extended offline Completed without error 00% 10744 - #18 Extended offline Completed without error 00% 10506 - #19 Extended offline Aborted by host 80% 9840 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 27/40 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 4294967295/4294901760 SMART Status: 0xffff (Reserved) SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (38) Index Estimated Time Temperature Celsius 39 2020-04-28 17:50 ? - ... ..( 87 skipped). .. - 127 2020-04-29 08:30 ? - 0 2020-04-29 08:40 40 ********************* 1 2020-04-29 08:50 27 ******** 2 2020-04-29 09:00 29 ********** 3 2020-04-29 09:10 31 ************ 4 2020-04-29 09:20 31 ************ 5 2020-04-29 09:30 32 ************* ... ..( 4 skipped). .. ************* 10 2020-04-29 10:20 32 ************* 11 2020-04-29 10:30 33 ************** 12 2020-04-29 10:40 32 ************* 13 2020-04-29 10:50 33 ************** ... ..( 4 skipped). .. ************** 18 2020-04-29 11:40 33 ************** 19 2020-04-29 11:50 32 ************* 20 2020-04-29 12:00 32 ************* 21 2020-04-29 12:10 32 ************* 22 2020-04-29 12:20 35 **************** 23 2020-04-29 12:30 35 **************** 24 2020-04-29 12:40 33 ************** ... ..( 5 skipped). .. ************** 30 2020-04-29 13:40 33 ************** 31 2020-04-29 13:50 34 *************** 32 2020-04-29 14:00 33 ************** 33 2020-04-29 14:10 32 ************* 34 2020-04-29 14:20 33 ************** 35 2020-04-29 14:30 34 *************** 36 2020-04-29 14:40 33 ************** 37 2020-04-29 14:50 33 ************** 38 2020-04-29 15:00 33 ************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.19.0-desktop-13.1rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green Device Model: WDC WD10EADS-00M2B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.00A01 User Capacity: 1,000,203,804,160 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Apr 29 15:07:28 2020 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (20400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 235) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 117 111 021 - 7133 4 Start_Stop_Count -O--CK 097 097 000 - 3476 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 013 013 000 - 64104 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3470 192 Power-Off_Retract_Count -O--CK 200 200 000 - 357 193 Load_Cycle_Count -O--CK 199 199 000 - 3118 194 Temperature_Celsius -O---K 110 095 000 - 37 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 198 197 000 - 581 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2375 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2375 [22] occurred at disk power-on lifetime: 24031 hours (1001 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 1e 00 00 00 14 2b c6 e0 00 Device Fault; Error: ABRT 30 sectors at LBA = 0x00142bc6 = 1321926 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 1e 00 14 00 2b 00 c6 e0 00 2d+20:43:16.101 READ DMA EXT 35 00 00 00 15 00 c1 00 ac 03 d8 e0 00 2d+20:43:16.083 WRITE DMA EXT 35 00 00 00 16 00 01 00 85 00 40 e0 00 2d+20:43:16.082 WRITE DMA EXT 25 00 00 00 10 00 17 00 80 00 24 e0 00 2d+20:43:16.054 READ DMA EXT 25 00 00 00 1d 00 09 00 0e 00 81 e0 00 2d+20:43:15.937 READ DMA EXT Error 2374 [21] occurred at disk power-on lifetime: 24031 hours (1001 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 15 00 00 03 c1 ac d8 e0 00 Device Fault; Error: ABRT 21 sectors at LBA = 0x03c1acd8 = 63024344 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 15 00 c1 00 ac 03 d8 e0 00 2d+20:43:16.083 WRITE DMA EXT 35 00 00 00 16 00 01 00 85 00 40 e0 00 2d+20:43:16.082 WRITE DMA EXT 25 00 00 00 10 00 17 00 80 00 24 e0 00 2d+20:43:16.054 READ DMA EXT 25 00 00 00 1d 00 09 00 0e 00 81 e0 00 2d+20:43:15.937 READ DMA EXT 25 00 00 00 40 00 00 00 72 00 58 e0 00 2d+20:43:15.902 READ DMA EXT Error 2373 [20] occurred at disk power-on lifetime: 24031 hours (1001 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 16 00 00 00 01 85 40 e0 00 Device Fault; Error: ABRT 22 sectors at LBA = 0x00018540 = 99648 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 16 00 01 00 85 00 40 e0 00 2d+20:43:16.082 WRITE DMA EXT 25 00 00 00 10 00 17 00 80 00 24 e0 00 2d+20:43:16.054 READ DMA EXT 25 00 00 00 1d 00 09 00 0e 00 81 e0 00 2d+20:43:15.937 READ DMA EXT 25 00 00 00 40 00 00 00 72 00 58 e0 00 2d+20:43:15.902 READ DMA EXT 35 00 00 00 a8 00 5d 00 e7 00 88 e0 00 2d+20:43:15.523 WRITE DMA EXT Error 2372 [19] occurred at disk power-on lifetime: 24031 hours (1001 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 10 00 00 00 17 80 24 e0 00 Device Fault; Error: ABRT 16 sectors at LBA = 0x00178024 = 1540132 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 17 00 80 00 24 e0 00 2d+20:43:16.054 READ DMA EXT 25 00 00 00 1d 00 09 00 0e 00 81 e0 00 2d+20:43:15.937 READ DMA EXT 25 00 00 00 40 00 00 00 72 00 58 e0 00 2d+20:43:15.902 READ DMA EXT 35 00 00 00 a8 00 5d 00 e7 00 88 e0 00 2d+20:43:15.523 WRITE DMA EXT 35 00 00 00 08 00 51 00 35 00 b8 e0 00 2d+20:43:15.522 WRITE DMA EXT Error 2371 [18] occurred at disk power-on lifetime: 24031 hours (1001 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 1d 00 00 00 09 0e 81 e0 00 Device Fault; Error: ABRT 29 sectors at LBA = 0x00090e81 = 593537 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 1d 00 09 00 0e 00 81 e0 00 2d+20:43:15.937 READ DMA EXT 25 00 00 00 40 00 00 00 72 00 58 e0 00 2d+20:43:15.902 READ DMA EXT 35 00 00 00 a8 00 5d 00 e7 00 88 e0 00 2d+20:43:15.523 WRITE DMA EXT 35 00 00 00 08 00 51 00 35 00 b8 e0 00 2d+20:43:15.522 WRITE DMA EXT 25 00 00 00 1e 00 14 00 2b 00 c6 e0 00 2d+20:43:15.103 READ DMA EXT Error 2370 [17] occurred at disk power-on lifetime: 24031 hours (1001 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 40 00 00 00 00 72 58 e0 00 Device Fault; Error: ABRT 64 sectors at LBA = 0x00007258 = 29272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 72 00 58 e0 00 2d+20:43:15.902 READ DMA EXT 35 00 00 00 a8 00 5d 00 e7 00 88 e0 00 2d+20:43:15.523 WRITE DMA EXT 35 00 00 00 08 00 51 00 35 00 b8 e0 00 2d+20:43:15.522 WRITE DMA EXT 25 00 00 00 1e 00 14 00 2b 00 c6 e0 00 2d+20:43:15.103 READ DMA EXT 25 00 00 00 1e 00 14 00 2b 00 c6 e0 00 2d+20:43:15.102 READ DMA EXT Error 2369 [16] occurred at disk power-on lifetime: 24031 hours (1001 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 a8 00 00 00 5d e7 88 e0 00 Device Fault; Error: ABRT 168 sectors at LBA = 0x005de788 = 6154120 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 a8 00 5d 00 e7 00 88 e0 00 2d+20:43:15.523 WRITE DMA EXT 35 00 00 00 08 00 51 00 35 00 b8 e0 00 2d+20:43:15.522 WRITE DMA EXT 25 00 00 00 1e 00 14 00 2b 00 c6 e0 00 2d+20:43:15.103 READ DMA EXT 25 00 00 00 1e 00 14 00 2b 00 c6 e0 00 2d+20:43:15.102 READ DMA EXT 35 00 00 00 15 00 c1 00 ac 03 d8 e0 00 2d+20:43:15.084 WRITE DMA EXT Error 2368 [15] occurred at disk power-on lifetime: 24031 hours (1001 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 08 00 00 00 51 35 b8 e0 00 Device Fault; Error: ABRT 8 sectors at LBA = 0x005135b8 = 5322168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 08 00 51 00 35 00 b8 e0 00 2d+20:43:15.522 WRITE DMA EXT 25 00 00 00 1e 00 14 00 2b 00 c6 e0 00 2d+20:43:15.103 READ DMA EXT 25 00 00 00 1e 00 14 00 2b 00 c6 e0 00 2d+20:43:15.102 READ DMA EXT 35 00 00 00 15 00 c1 00 ac 03 d8 e0 00 2d+20:43:15.084 WRITE DMA EXT 35 00 00 00 16 00 01 00 85 00 40 e0 00 2d+20:43:15.083 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 63891 - # 2 Extended offline Completed without error 00% 63547 - # 3 Extended offline Interrupted (host reset) 90% 63202 - # 4 Extended offline Completed without error 00% 63072 - # 5 Extended offline Completed without error 00% 62685 - # 6 Extended offline Completed without error 00% 62298 - # 7 Extended offline Completed without error 00% 61036 - # 8 Extended offline Completed without error 00% 60701 - # 9 Extended offline Completed without error 00% 60442 - #10 Extended offline Completed without error 00% 59621 - #11 Extended offline Completed without error 00% 59279 - #12 Extended offline Completed without error 00% 59163 - #13 Extended offline Completed without error 00% 58823 - #14 Extended offline Completed without error 00% 58597 - #15 Extended offline Completed without error 00% 58360 - #16 Extended offline Completed without error 00% 57444 - #17 Extended offline Completed without error 00% 55955 - #18 Extended offline Completed without error 00% 55810 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 22/36 Celsius Lifetime Min/Max Temperature: 23/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (145) Index Estimated Time Temperature Celsius 146 2020-04-29 07:10 36 ***************** ... ..( 30 skipped). .. ***************** 177 2020-04-29 07:41 36 ***************** 178 2020-04-29 07:42 37 ****************** ... ..( 2 skipped). .. ****************** 181 2020-04-29 07:45 37 ****************** 182 2020-04-29 07:46 36 ***************** ... ..( 46 skipped). .. ***************** 229 2020-04-29 08:33 36 ***************** 230 2020-04-29 08:34 37 ****************** 231 2020-04-29 08:35 37 ****************** 232 2020-04-29 08:36 36 ***************** 233 2020-04-29 08:37 36 ***************** 234 2020-04-29 08:38 36 ***************** 235 2020-04-29 08:39 37 ****************** ... ..( 2 skipped). .. ****************** 238 2020-04-29 08:42 37 ****************** 239 2020-04-29 08:43 36 ***************** ... ..( 4 skipped). .. ***************** 244 2020-04-29 08:48 36 ***************** 245 2020-04-29 08:49 37 ****************** 246 2020-04-29 08:50 36 ***************** ... ..( 2 skipped). .. ***************** 249 2020-04-29 08:53 36 ***************** 250 2020-04-29 08:54 37 ****************** 251 2020-04-29 08:55 37 ****************** 252 2020-04-29 08:56 36 ***************** 253 2020-04-29 08:57 36 ***************** 254 2020-04-29 08:58 36 ***************** 255 2020-04-29 08:59 37 ****************** ... ..( 2 skipped). .. ****************** 258 2020-04-29 09:02 37 ****************** 259 2020-04-29 09:03 36 ***************** 260 2020-04-29 09:04 37 ****************** 261 2020-04-29 09:05 37 ****************** 262 2020-04-29 09:06 36 ***************** 263 2020-04-29 09:07 36 ***************** 264 2020-04-29 09:08 36 ***************** 265 2020-04-29 09:09 37 ****************** 266 2020-04-29 09:10 37 ****************** 267 2020-04-29 09:11 ? - 268 2020-04-29 09:12 22 *** 269 2020-04-29 09:13 23 **** ... ..( 2 skipped). .. **** 272 2020-04-29 09:16 23 **** 273 2020-04-29 09:17 24 ***** 274 2020-04-29 09:18 25 ****** ... ..( 3 skipped). .. ****** 278 2020-04-29 09:22 25 ****** 279 2020-04-29 09:23 26 ******* ... ..( 2 skipped). .. ******* 282 2020-04-29 09:26 26 ******* 283 2020-04-29 09:27 27 ******** 284 2020-04-29 09:28 28 ********* ... ..( 2 skipped). .. ********* 287 2020-04-29 09:31 28 ********* 288 2020-04-29 09:32 29 ********** 289 2020-04-29 09:33 30 *********** ... ..( 7 skipped). .. *********** 297 2020-04-29 09:41 30 *********** 298 2020-04-29 09:42 31 ************ ... ..( 3 skipped). .. ************ 302 2020-04-29 09:46 31 ************ 303 2020-04-29 09:47 32 ************* ... ..( 4 skipped). .. ************* 308 2020-04-29 09:52 32 ************* 309 2020-04-29 09:53 33 ************** ... ..( 18 skipped). .. ************** 328 2020-04-29 10:12 33 ************** 329 2020-04-29 10:13 34 *************** ... ..( 18 skipped). .. *************** 348 2020-04-29 10:32 34 *************** 349 2020-04-29 10:33 35 **************** ... ..( 53 skipped). .. **************** 403 2020-04-29 11:27 35 **************** 404 2020-04-29 11:28 36 ***************** ... ..( 65 skipped). .. ***************** 470 2020-04-29 12:34 36 ***************** 471 2020-04-29 12:35 35 **************** ... ..( 31 skipped). .. **************** 25 2020-04-29 13:07 35 **************** 26 2020-04-29 13:08 36 ***************** ... ..( 2 skipped). .. ***************** 29 2020-04-29 13:11 36 ***************** 30 2020-04-29 13:12 35 **************** 31 2020-04-29 13:13 36 ***************** ... ..( 17 skipped). .. ***************** 49 2020-04-29 13:31 36 ***************** 50 2020-04-29 13:32 35 **************** 51 2020-04-29 13:33 36 ***************** ... ..( 93 skipped). .. ***************** 145 2020-04-29 15:07 36 ***************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 23301 Vendor specific /dev/sdc smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.19.0-desktop-13.1rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD10EARS-00Y5B1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Apr 29 15:07:29 2020 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (19800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 228) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 122 118 021 - 6858 4 Start_Stop_Count -O--CK 096 096 000 - 4055 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 019 019 000 - 59538 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3382 192 Power-Off_Retract_Count -O--CK 199 199 000 - 1056 193 Load_Cycle_Count -O--CK 001 001 000 - 1204880 194 Temperature_Celsius -O---K 104 093 000 - 43 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 194 192 000 - 1000 198 Offline_Uncorrectable ----CK 200 194 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 178 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 462 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 462 [5] occurred at disk power-on lifetime: 56276 hours (2344 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 52 7d 0a 88 40 00 Error: UNC at LBA = 0x527d0a88 = 1383926408 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 4f 58 9c 10 40 08 00:49:15.358 READ FPDMA QUEUED 60 00 80 00 10 00 00 54 05 81 00 40 08 00:49:15.343 READ FPDMA QUEUED 60 00 18 00 38 00 00 54 05 12 68 40 08 00:49:15.342 READ FPDMA QUEUED 60 00 38 00 30 00 00 54 05 11 80 40 08 00:49:15.342 READ FPDMA QUEUED 60 00 08 00 28 00 00 4f 58 9c 18 40 08 00:49:15.342 READ FPDMA QUEUED Error 461 [4] occurred at disk power-on lifetime: 56276 hours (2344 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 80 00 00 52 7d 0a 80 40 00 Error: UNC at LBA = 0x527d0a80 = 1383926400 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 e8 00 00 52 7d 0a 80 40 08 00:49:07.184 READ FPDMA QUEUED 60 00 58 00 e0 00 00 54 03 ef 80 40 08 00:49:07.166 READ FPDMA QUEUED 60 00 78 00 d8 00 00 53 fe 02 00 40 08 00:49:07.158 READ FPDMA QUEUED 60 00 20 00 d0 00 00 53 fe 01 60 40 08 00:49:07.147 READ FPDMA QUEUED 60 00 28 00 c8 00 00 53 fc 73 d8 40 08 00:49:07.130 READ FPDMA QUEUED Error 460 [3] occurred at disk power-on lifetime: 56275 hours (2344 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 59 19 52 d0 40 00 Error: UNC at LBA = 0x591952d0 = 1494831824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 d8 00 00 47 93 69 d8 40 08 00:20:54.000 READ FPDMA QUEUED 60 00 08 00 c8 00 00 47 93 69 d0 40 08 00:20:54.000 READ FPDMA QUEUED 60 00 08 00 c0 00 00 47 93 69 c8 40 08 00:20:54.000 READ FPDMA QUEUED 60 00 08 00 00 00 00 47 93 69 c0 40 08 00:20:53.967 READ FPDMA QUEUED 60 00 08 00 d0 00 00 59 19 52 d0 40 08 00:20:53.967 READ FPDMA QUEUED Error 459 [2] occurred at disk power-on lifetime: 56275 hours (2344 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 59 19 52 d0 40 00 Error: UNC at LBA = 0x591952d0 = 1494831824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 68 00 00 46 fe f2 c0 40 08 00:20:51.163 READ FPDMA QUEUED 60 00 08 00 c8 00 00 47 93 69 c0 40 08 00:20:51.159 READ FPDMA QUEUED 60 00 08 00 c0 00 00 47 93 69 b8 40 08 00:20:51.159 READ FPDMA QUEUED 60 00 08 00 b8 00 00 47 93 69 b0 40 08 00:20:51.159 READ FPDMA QUEUED 60 00 08 00 a8 00 00 46 0f a0 b8 40 08 00:20:51.145 READ FPDMA QUEUED Error 458 [1] occurred at disk power-on lifetime: 56275 hours (2344 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 59 19 52 c0 40 00 Error: UNC at LBA = 0x591952c0 = 1494831808 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b8 00 00 59 19 52 c0 40 08 00:20:46.901 READ FPDMA QUEUED 60 00 08 00 b0 00 00 59 19 52 b8 40 08 00:20:46.901 READ FPDMA QUEUED 60 00 80 00 b8 00 00 47 93 69 00 40 08 00:20:46.892 READ FPDMA QUEUED 60 00 10 00 b0 00 00 47 93 68 f0 40 08 00:20:46.891 READ FPDMA QUEUED 60 00 08 00 a8 00 00 59 19 52 b0 40 08 00:20:46.891 READ FPDMA QUEUED Error 457 [0] occurred at disk power-on lifetime: 56275 hours (2344 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 59 19 51 70 40 00 Error: UNC at LBA = 0x59195170 = 1494831472 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 47 93 68 20 40 08 00:20:39.379 READ FPDMA QUEUED 60 00 08 00 38 00 00 47 93 68 18 40 08 00:20:39.379 READ FPDMA QUEUED 60 00 08 00 30 00 00 47 93 68 10 40 08 00:20:39.379 READ FPDMA QUEUED 60 00 08 00 98 00 00 37 10 ce 00 40 08 00:20:39.379 READ FPDMA QUEUED 60 00 08 00 10 00 00 47 93 68 08 40 08 00:20:39.348 READ FPDMA QUEUED Error 456 [23] occurred at disk power-on lifetime: 56275 hours (2344 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 59 19 51 70 40 00 Error: UNC at LBA = 0x59195170 = 1494831472 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 28 00 00 58 2a 21 50 40 08 00:20:36.562 READ FPDMA QUEUED 60 00 08 00 90 00 00 47 93 68 08 40 08 00:20:36.562 READ FPDMA QUEUED 60 00 08 00 68 00 00 47 93 68 00 40 08 00:20:36.562 READ FPDMA QUEUED 60 00 08 00 60 00 00 47 93 67 f8 40 08 00:20:35.705 READ FPDMA QUEUED 60 00 08 00 78 00 00 59 19 51 70 40 08 00:20:35.675 READ FPDMA QUEUED Error 455 [22] occurred at disk power-on lifetime: 56275 hours (2344 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 59 19 51 48 40 00 Error: UNC at LBA = 0x59195148 = 1494831432 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 d0 00 00 58 25 f2 a0 40 08 00:20:31.030 READ FPDMA QUEUED 60 00 08 00 c8 00 00 58 25 f2 98 40 08 00:20:31.030 READ FPDMA QUEUED 60 00 08 00 c0 00 00 47 93 67 c8 40 08 00:20:31.021 READ FPDMA QUEUED 60 00 08 00 b8 00 00 47 93 67 c0 40 08 00:20:31.020 READ FPDMA QUEUED 60 00 08 00 b0 00 00 47 93 67 b8 40 08 00:20:31.020 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 59327 - # 2 Extended offline Completed without error 00% 58989 - # 3 Extended offline Interrupted (host reset) 90% 58649 - # 4 Extended offline Completed without error 00% 58520 - # 5 Extended offline Completed without error 00% 58139 - # 6 Extended offline Completed without error 00% 57756 - # 7 Extended offline Completed without error 00% 56503 - # 8 Extended offline Completed without error 00% 56169 - # 9 Extended offline Completed without error 00% 55913 - #10 Extended offline Completed without error 00% 55097 - #11 Extended offline Completed without error 00% 54757 - #12 Extended offline Completed without error 00% 54641 - #13 Extended offline Completed without error 00% 54304 - #14 Extended offline Completed without error 00% 54079 - #15 Extended offline Completed without error 00% 53843 - #16 Extended offline Completed without error 00% 52934 - #17 Extended offline Completed without error 00% 51449 - #18 Extended offline Completed without error 00% 51306 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 43 Celsius Power Cycle Min/Max Temperature: 23/43 Celsius Lifetime Min/Max Temperature: ?/53 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (253) Index Estimated Time Temperature Celsius 254 2020-04-29 07:10 36 ***************** ... ..( 11 skipped). .. ***************** 266 2020-04-29 07:22 36 ***************** 267 2020-04-29 07:23 37 ****************** 268 2020-04-29 07:24 36 ***************** ... ..( 7 skipped). .. ***************** 276 2020-04-29 07:32 36 ***************** 277 2020-04-29 07:33 37 ****************** ... ..( 48 skipped). .. ****************** 326 2020-04-29 08:22 37 ****************** 327 2020-04-29 08:23 38 ******************* ... ..( 47 skipped). .. ******************* 375 2020-04-29 09:11 38 ******************* 376 2020-04-29 09:12 37 ****************** ... ..( 38 skipped). .. ****************** 415 2020-04-29 09:51 37 ****************** 416 2020-04-29 09:52 38 ******************* 417 2020-04-29 09:53 37 ****************** ... ..( 8 skipped). .. ****************** 426 2020-04-29 10:02 37 ****************** 427 2020-04-29 10:03 38 ******************* 428 2020-04-29 10:04 38 ******************* 429 2020-04-29 10:05 38 ******************* 430 2020-04-29 10:06 37 ****************** ... ..( 14 skipped). .. ****************** 445 2020-04-29 10:21 37 ****************** 446 2020-04-29 10:22 38 ******************* ... ..( 32 skipped). .. ******************* 1 2020-04-29 10:55 38 ******************* 2 2020-04-29 10:56 39 ******************** 3 2020-04-29 10:57 39 ******************** 4 2020-04-29 10:58 40 ********************* ... ..( 3 skipped). .. ********************* 8 2020-04-29 11:02 40 ********************* 9 2020-04-29 11:03 41 ********************** ... ..( 8 skipped). .. ********************** 18 2020-04-29 11:12 41 ********************** 19 2020-04-29 11:13 42 *********************** ... ..( 18 skipped). .. *********************** 38 2020-04-29 11:32 42 *********************** 39 2020-04-29 11:33 43 ************************ ... ..( 45 skipped). .. ************************ 85 2020-04-29 12:19 43 ************************ 86 2020-04-29 12:20 40 ********************* ... ..( 4 skipped). .. ********************* 91 2020-04-29 12:25 40 ********************* 92 2020-04-29 12:26 39 ******************** 93 2020-04-29 12:27 40 ********************* 94 2020-04-29 12:28 39 ******************** ... ..( 47 skipped). .. ******************** 142 2020-04-29 13:16 39 ******************** 143 2020-04-29 13:17 40 ********************* ... ..( 30 skipped). .. ********************* 174 2020-04-29 13:48 40 ********************* 175 2020-04-29 13:49 ? - 176 2020-04-29 13:50 23 **** 177 2020-04-29 13:51 24 ***** 178 2020-04-29 13:52 24 ***** 179 2020-04-29 13:53 24 ***** 180 2020-04-29 13:54 25 ****** ... ..( 2 skipped). .. ****** 183 2020-04-29 13:57 25 ****** 184 2020-04-29 13:58 26 ******* 185 2020-04-29 13:59 26 ******* 186 2020-04-29 14:00 26 ******* 187 2020-04-29 14:01 27 ******** 188 2020-04-29 14:02 27 ******** 189 2020-04-29 14:03 28 ********* 190 2020-04-29 14:04 28 ********* 191 2020-04-29 14:05 29 ********** ... ..( 3 skipped). .. ********** 195 2020-04-29 14:09 29 ********** 196 2020-04-29 14:10 30 *********** 197 2020-04-29 14:11 30 *********** 198 2020-04-29 14:12 30 *********** 199 2020-04-29 14:13 31 ************ 200 2020-04-29 14:14 31 ************ 201 2020-04-29 14:15 31 ************ 202 2020-04-29 14:16 32 ************* ... ..( 3 skipped). .. ************* 206 2020-04-29 14:20 32 ************* 207 2020-04-29 14:21 33 ************** ... ..( 7 skipped). .. ************** 215 2020-04-29 14:29 33 ************** 216 2020-04-29 14:30 34 *************** ... ..( 4 skipped). .. *************** 221 2020-04-29 14:35 34 *************** 222 2020-04-29 14:36 35 **************** ... ..( 3 skipped). .. **************** 226 2020-04-29 14:40 35 **************** 227 2020-04-29 14:41 36 ***************** ... ..( 25 skipped). .. ***************** 253 2020-04-29 15:07 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 23294 Vendor specific /dev/sdd smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.19.0-desktop-13.1rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: HGST HUS726T6TALE6L4 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: VKGNW40H User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Apr 29 15:07:29 2020 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 87) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 649) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 132 132 054 - 94 3 Spin_Up_Time POS--- 151 151 024 - 399 (Average 398) 4 Start_Stop_Count -O--C- 100 100 000 - 98 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 128 128 020 - 18 9 Power_On_Hours -O--C- 100 100 000 - 1958 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 98 192 Power-Off_Retract_Count -O--CK 100 100 000 - 247 193 Load_Cycle_Count -O--C- 100 100 000 - 247 194 Temperature_Celsius -O---- 146 146 000 - 41 (Min/Max 20/45) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 5501 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 1752 - # 2 Extended offline Aborted by host 90% 1516 - # 3 Extended offline Completed without error 00% 1407 - # 4 Extended offline Interrupted (host reset) 90% 1055 - # 5 Extended offline Completed without error 00% 932 - # 6 Extended offline Completed without error 00% 544 - # 7 Extended offline Completed without error 00% 155 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 22/41 Celsius Lifetime Min/Max Temperature: 20/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (21) Index Estimated Time Temperature Celsius 22 2020-04-29 13:00 41 ********************** ... ..( 89 skipped). .. ********************** 112 2020-04-29 14:30 41 ********************** 113 2020-04-29 14:31 40 ********************* ... ..( 32 skipped). .. ********************* 18 2020-04-29 15:04 40 ********************* 19 2020-04-29 15:05 41 ********************** 20 2020-04-29 15:06 41 ********************** 21 2020-04-29 15:07 41 ********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 98 --- Lifetime Power-On Resets 0x01 0x010 4 1958 --- Power-on Hours 0x01 0x018 6 10051354280 --- Logical Sectors Written 0x01 0x020 6 27588172 --- Number of Write Commands 0x01 0x028 6 5518753999 --- Logical Sectors Read 0x01 0x030 6 22161076 --- Number of Read Commands 0x01 0x038 6 7051286950 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 1934 --- Spindle Motor Power-on Hours 0x03 0x010 4 1934 --- Head Flying Hours 0x03 0x018 4 247 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 41 --- Current Temperature 0x05 0x010 1 40 N-- Average Short Term Temperature 0x05 0x018 1 40 N-- Average Long Term Temperature 0x05 0x020 1 45 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x030 1 42 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 41 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 4 --- Number of Hardware Resets 0x06 0x010 4 144 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sde smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.19.0-desktop-13.1rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD4003FRYZ-01F0DB0 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: 01.01H01 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Apr 29 15:07:29 2020 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 87) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 485) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 132 132 054 - 96 3 Spin_Up_Time POS--- 142 142 024 - 299 (Average 299) 4 Start_Stop_Count -O--C- 100 100 000 - 106 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 128 128 020 - 18 9 Power_On_Hours -O--C- 100 100 000 - 2010 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 106 192 Power-Off_Retract_Count -O--CK 100 100 000 - 358 193 Load_Cycle_Count -O--C- 100 100 000 - 358 194 Temperature_Celsius -O---- 153 153 000 - 39 (Min/Max 20/45) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 5501 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x2f GPL - 1 Set Sector Configuration 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 1800 - # 2 Extended offline Aborted by host 90% 1567 - # 3 Extended offline Completed without error 00% 1456 - # 4 Extended offline Interrupted (host reset) 90% 1107 - # 5 Extended offline Completed without error 00% 980 - # 6 Extended offline Completed without error 00% 592 - # 7 Extended offline Completed without error 00% 204 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 21/40 Celsius Lifetime Min/Max Temperature: 20/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (34) Index Estimated Time Temperature Celsius 35 2020-04-29 13:00 39 ******************** ... ..( 26 skipped). .. ******************** 62 2020-04-29 13:27 39 ******************** 63 2020-04-29 13:28 40 ********************* ... ..( 13 skipped). .. ********************* 77 2020-04-29 13:42 40 ********************* 78 2020-04-29 13:43 39 ******************** ... ..( 20 skipped). .. ******************** 99 2020-04-29 14:04 39 ******************** 100 2020-04-29 14:05 38 ******************* ... ..( 18 skipped). .. ******************* 119 2020-04-29 14:24 38 ******************* 120 2020-04-29 14:25 39 ******************** ... ..( 5 skipped). .. ******************** 126 2020-04-29 14:31 39 ******************** 127 2020-04-29 14:32 38 ******************* ... ..( 28 skipped). .. ******************* 28 2020-04-29 15:01 38 ******************* 29 2020-04-29 15:02 39 ******************** ... ..( 4 skipped). .. ******************** 34 2020-04-29 15:07 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 106 --- Lifetime Power-On Resets 0x01 0x010 4 2010 --- Power-on Hours 0x01 0x018 6 16517662243 --- Logical Sectors Written 0x01 0x020 6 42117777 --- Number of Write Commands 0x01 0x028 6 5476519361 --- Logical Sectors Read 0x01 0x030 6 29912639 --- Number of Read Commands 0x01 0x038 6 7236069950 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 1960 --- Spindle Motor Power-on Hours 0x03 0x010 4 1960 --- Head Flying Hours 0x03 0x018 4 358 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 39 --- Current Temperature 0x05 0x010 1 38 N-- Average Short Term Temperature 0x05 0x018 1 38 N-- Average Long Term Temperature 0x05 0x020 1 45 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x030 1 42 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 41 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 749 --- Number of Hardware Resets 0x06 0x010 4 163 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS