/dev/sda === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT Device Model: SAMSUNG HD753LJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: 1AA01110 User Capacity: 750 156 374 016 bytes [750 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Wed Mar 22 15:54:39 2017 +10 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: (11393) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 191) minutes. Conveyance self-test routine recommended polling time: ( 20) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 099 098 051 - 263 3 Spin_Up_Time POS--- 083 083 011 - 6120 4 Start_Stop_Count -O--CK 094 094 000 - 5907 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 100 096 015 - 12621 9 Power_On_Hours -O--CK 093 093 000 - 35693 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 4 12 Power_Cycle_Count -O--CK 094 094 000 - 5907 13 Read_Soft_Error_Rate -OSR-- 100 099 000 - 33 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 37 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 050 000 - 37 (Min/Max 36/37) 194 Temperature_Celsius -O---K 062 045 000 - 38 (Min/Max 36/39) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 12891 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 1 198 Offline_Uncorrectable ----CK 100 100 000 - 1 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 96 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 96 [7] occurred at disk power-on lifetime: 17834 hours (743 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 18 5d 72 57 e0 00 Error: UNC at LBA = 0x185d7257 = 408777303 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 18 5d 72 57 e0 08 11:08:30.330 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:30.330 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 11:08:30.310 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 11:08:30.310 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:30.310 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 95 [6] occurred at disk power-on lifetime: 17834 hours (743 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 18 5d 72 57 e0 00 Error: UNC at LBA = 0x185d7257 = 408777303 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 18 5d 72 57 e0 08 11:08:28.580 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:28.580 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 11:08:28.560 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 11:08:28.560 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:28.560 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 94 [5] occurred at disk power-on lifetime: 17834 hours (743 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 18 5d 72 57 e0 00 Error: UNC at LBA = 0x185d7257 = 408777303 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 18 5d 72 57 e0 08 11:08:26.820 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:26.820 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 11:08:26.800 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 11:08:26.800 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:26.800 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 93 [4] occurred at disk power-on lifetime: 17834 hours (743 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 18 5d 72 57 e0 00 Error: UNC at LBA = 0x185d7257 = 408777303 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 18 5d 72 57 e0 08 11:08:25.060 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:25.060 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 11:08:25.040 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 11:08:25.040 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:25.040 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 92 [3] occurred at disk power-on lifetime: 17834 hours (743 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 18 5d 72 57 e0 00 Error: UNC at LBA = 0x185d7257 = 408777303 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 18 5d 72 57 e0 08 11:08:23.310 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:23.300 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 11:08:23.290 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 11:08:23.290 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:23.290 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 91 [2] occurred at disk power-on lifetime: 17834 hours (743 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 18 5d 72 57 e0 00 Error: UNC at LBA = 0x185d7257 = 408777303 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 18 5d 72 57 e0 08 11:08:21.550 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:21.550 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 11:08:21.530 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 11:08:21.530 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:21.530 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 90 [1] occurred at disk power-on lifetime: 17834 hours (743 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 18 5d 72 57 e0 00 Error: UNC at LBA = 0x185d7257 = 408777303 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 18 5d 72 57 e0 08 11:08:19.790 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:19.790 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 11:08:19.770 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 11:08:19.770 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:19.770 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 89 [0] occurred at disk power-on lifetime: 17834 hours (743 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 18 5d 72 57 e0 00 Error: UNC at LBA = 0x185d7257 = 408777303 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 18 5d 72 57 e0 08 11:08:18.030 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:18.030 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 11:08:18.010 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 11:08:18.010 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 11:08:18.010 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] SMART Extended Self-test Log Version: 0 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 35651 408777303 # 2 Extended offline Aborted by host 90% 35557 - # 3 Extended offline Aborted by host 90% 35455 - # 4 Extended offline Aborted by host 90% 35346 - # 5 Extended offline Aborted by host 90% 35247 - # 6 Extended offline Aborted by host 90% 35150 - # 7 Extended offline Aborted by host 90% 34945 - # 8 Extended offline Aborted by host 90% 34840 - # 9 Extended offline Aborted by host 90% 34743 - #10 Extended offline Aborted by host 90% 34494 - #11 Extended offline Aborted by host 90% 34404 - #12 Extended offline Aborted by host 90% 34185 - #13 Extended offline Aborted by host 90% 34027 - #14 Extended offline Aborted by host 90% 33340 - #15 Extended offline Aborted by host 90% 33159 - #16 Extended offline Aborted by host 90% 33119 - #17 Extended offline Aborted by host 90% 33037 - #18 Extended offline Aborted by host 90% 32869 - #19 Extended offline Aborted by host 90% 32756 - #20 Extended offline Aborted by host 90% 32683 - #21 Extended offline Aborted by host 90% 32599 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Max Temperature: 39 Celsius Lifetime Max Temperature: 55 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (18) Index Estimated Time Temperature Celsius 19 2017-03-22 13:47 33 ************** 20 2017-03-22 13:48 33 ************** 21 2017-03-22 13:49 34 *************** ... ..( 4 skipped). .. *************** 26 2017-03-22 13:54 34 *************** 27 2017-03-22 13:55 35 **************** ... ..( 2 skipped). .. **************** 30 2017-03-22 13:58 35 **************** 31 2017-03-22 13:59 ? - 32 2017-03-22 14:00 36 ***************** 33 2017-03-22 14:01 ? - 34 2017-03-22 14:02 36 ***************** ... ..( 2 skipped). .. ***************** 37 2017-03-22 14:05 36 ***************** 38 2017-03-22 14:06 37 ****************** ... ..( 19 skipped). .. ****************** 58 2017-03-22 14:26 37 ****************** 59 2017-03-22 14:27 38 ******************* ... ..( 74 skipped). .. ******************* 6 2017-03-22 15:42 38 ******************* 7 2017-03-22 15:43 39 ******************** 8 2017-03-22 15:44 39 ******************** 9 2017-03-22 15:45 38 ******************* ... ..( 5 skipped). .. ******************* 15 2017-03-22 15:51 38 ******************* 16 2017-03-22 15:52 39 ******************** 17 2017-03-22 15:53 38 ******************* 18 2017-03-22 15:54 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 31 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 31 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint T166 Device Model: SAMSUNG HD403LJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: CT100-11 User Capacity: 400 088 457 216 bytes [400 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 3b SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Wed Mar 22 15:54:40 2017 +10 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 7436) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 126) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 253 100 051 - 4 3 Spin_Up_Time POS--- 100 100 015 - 6656 4 Start_Stop_Count -O--CK 088 088 000 - 12672 5 Reallocated_Sector_Ct PO--CK 253 253 010 - 0 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 42305 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 100 000 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 6637 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 109077 187 Reported_Uncorrect -O--CK 253 253 000 - 1114112 188 Command_Timeout -O--CK 253 253 000 - 0 190 Airflow_Temperature_Cel -O---K 059 045 000 - 41 194 Temperature_Celsius -O---K 115 073 000 - 41 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 109077 196 Reallocated_Event_Count -O--CK 253 253 000 - 0 197 Total_Pending_Sectors -O--C- 100 100 000 - 2 198 Offline_Uncorrectable ----CK 253 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 253 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 100 000 - 18 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Invalid Error Log index = 0x0000, trying reserved byte (0x06) instead Device Error Count: 6 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [5] occurred at disk power-on lifetime: 42093 hours (1753 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 2c 3c 07 1f 40 00 Error: UNC at LBA = 0x2c3c071f = 742131487 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 10 08 00 00 00 00 2c 3c 07 1f 40 00 05:31:18.938 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 05:31:16.063 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 05:31:16.063 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 05:31:16.063 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 05:31:16.063 SET FEATURES [Set transfer mode] Error 5 [4] occurred at disk power-on lifetime: 42093 hours (1753 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 13 98 00 00 2c 3c 07 1f 40 00 Error: UNC at LBA = 0x2c3c071f = 742131487 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 08 08 13 98 00 00 2c 3c 07 1f 40 00 05:31:15.938 READ FPDMA QUEUED 60 08 08 12 90 00 00 2c 3c 08 6f 40 00 05:31:13.125 READ FPDMA QUEUED 60 08 08 11 88 00 00 2c 3c 08 67 40 00 05:31:13.125 READ FPDMA QUEUED 60 08 08 10 80 00 00 2c 3c 08 5f 40 00 05:31:13.125 READ FPDMA QUEUED 60 08 08 0f 78 00 00 2c 3c 08 57 40 00 05:31:13.125 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 42093 hours (1753 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 1d e8 00 00 2c 3c 07 1f 40 00 Error: UNC at LBA = 0x2c3c071f = 742131487 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 10 08 1d e8 00 00 2c 3c 07 1f 40 00 05:31:12.938 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 05:31:10.125 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 05:31:10.125 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 05:31:10.125 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 05:31:10.125 SET FEATURES [Set transfer mode] Error 3 [2] occurred at disk power-on lifetime: 42093 hours (1753 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 11 88 00 00 2c 3c 07 1f 40 00 Error: UNC at LBA = 0x2c3c071f = 742131487 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 10 08 11 88 00 00 2c 3c 07 1f 40 00 05:31:10.000 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 00 05:31:07.125 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 05:31:07.125 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 05:31:07.125 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 05:31:07.125 SET FEATURES [Set transfer mode] Error 2 [1] occurred at disk power-on lifetime: 42093 hours (1753 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 0d 68 00 00 2c 3c 07 1f 40 00 Error: UNC at LBA = 0x2c3c071f = 742131487 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 08 08 0d 68 00 00 2c 3c 07 1f 40 00 05:31:07.000 READ FPDMA QUEUED 60 08 08 0c 60 00 00 2c 3c 07 17 40 00 05:31:04.125 READ FPDMA QUEUED 60 08 08 0b 58 00 00 2c 3c 07 0f 40 00 05:31:04.125 READ FPDMA QUEUED 60 08 08 0a 50 00 00 2c 3c 07 07 40 00 05:31:04.125 READ FPDMA QUEUED 60 08 08 09 48 00 00 2c 3c 06 ff 40 00 05:31:04.125 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 42093 hours (1753 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 0c 60 00 00 2c 3c 06 77 40 00 Error: UNC at LBA = 0x2c3c0677 = 742131319 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 0c 60 00 00 2c 3c 06 77 40 00 05:31:03.625 READ FPDMA QUEUED 60 00 00 0b 58 00 00 2c 3c 05 77 40 00 05:31:00.563 READ FPDMA QUEUED 60 00 00 0a 50 00 00 2c 3c 04 77 40 00 05:31:00.563 READ FPDMA QUEUED 60 00 00 09 48 00 00 2d a8 0e 07 40 00 05:31:00.563 READ FPDMA QUEUED 60 00 00 08 40 00 00 2d a8 0d 07 40 00 05:31:00.563 READ FPDMA QUEUED SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 42263 749703024 # 2 Extended offline Completed: read failure 90% 42169 749703024 # 3 Extended offline Completed without error 00% 39649 - # 4 Extended offline Completed: read failure 90% 39114 680259892 # 5 Extended offline Completed without error 00% 38856 - # 6 Extended offline Completed without error 00% 38375 - # 7 Extended offline Completed without error 00% 34597 - # 8 Extended offline Completed: read failure 10% 33104 743586642 # 9 Extended offline Completed without error 00% 32709 - #10 Extended offline Completed without error 00% 31946 - #11 Extended offline Completed without error 00% 31184 - #12 Extended offline Completed without error 00% 23142 - #13 Extended offline Completed without error 00% 23057 - #14 Extended offline Completed without error 00% 22382 - #15 Extended offline Completed without error 00% 22108 - #16 Extended offline Completed without error 00% 22034 - #17 Extended offline Completed without error 00% 21410 - #18 Extended offline Completed without error 00% 21323 - #19 Extended offline Completed without error 00% 17485 - #20 Extended offline Completed without error 00% 17335 - #21 Extended offline Completed without error 00% 16976 - 2 of 4 failed self-tests are outdated by newer successful extended offline self-test # 3 SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 39/41 Celsius Lifetime Min/Max Temperature: 14/57 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (2) Index Estimated Time Temperature Celsius 3 2017-03-22 13:47 32 ************* 4 2017-03-22 13:48 32 ************* 5 2017-03-22 13:49 32 ************* 6 2017-03-22 13:50 33 ************** 7 2017-03-22 13:51 33 ************** 8 2017-03-22 13:52 35 **************** ... ..( 3 skipped). .. **************** 12 2017-03-22 13:56 35 **************** 13 2017-03-22 13:57 36 ***************** 14 2017-03-22 13:58 36 ***************** 15 2017-03-22 13:59 37 ****************** ... ..( 5 skipped). .. ****************** 21 2017-03-22 14:05 37 ****************** 22 2017-03-22 14:06 38 ******************* ... ..( 9 skipped). .. ******************* 32 2017-03-22 14:16 38 ******************* 33 2017-03-22 14:17 39 ******************** ... ..( 14 skipped). .. ******************** 48 2017-03-22 14:32 39 ******************** 49 2017-03-22 14:33 40 ********************* ... ..( 68 skipped). .. ********************* 118 2017-03-22 15:42 40 ********************* 119 2017-03-22 15:43 41 ********************** 120 2017-03-22 15:44 40 ********************* 121 2017-03-22 15:45 41 ********************** ... ..( 7 skipped). .. ********************** 1 2017-03-22 15:53 41 ********************** 2 2017-03-22 15:54 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 31 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8001 2 0 Vendor specific /dev/sdc === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD10EARS-00Y5B1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Mar 22 15:54:40 2017 +10 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (21300) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 245) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 132 125 021 - 6358 4 Start_Stop_Count -O--CK 097 097 000 - 3713 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 068 068 000 - 23665 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3711 192 Power-Off_Retract_Count -O--CK 200 200 000 - 166 193 Load_Cycle_Count -O--CK 001 001 000 - 885212 194 Temperature_Celsius -O---K 106 092 000 - 41 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 5 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [4] occurred at disk power-on lifetime: 23497 hours (979 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 72 0a 91 98 40 00 Error: UNC at LBA = 0x720a9198 = 1913295256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 88 00 00 72 0a 91 98 40 08 15:31:40.932 READ FPDMA QUEUED 60 00 08 00 80 00 00 72 0a 91 28 40 08 15:31:40.931 READ FPDMA QUEUED 60 00 08 00 78 00 00 72 0a 91 38 40 08 15:31:40.930 READ FPDMA QUEUED 60 00 08 00 70 00 00 72 0a 91 10 40 08 15:31:40.930 READ FPDMA QUEUED 60 00 08 00 68 00 00 72 0a 91 e0 40 08 15:31:40.929 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 23369 hours (973 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 72 0a 91 98 40 00 Error: UNC at LBA = 0x720a9198 = 1913295256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 60 00 00 72 0a 91 98 40 08 07:24:33.424 READ FPDMA QUEUED 61 00 20 00 58 00 00 6b ae 8e 28 40 08 07:24:33.424 WRITE FPDMA QUEUED 61 00 08 00 50 00 00 3b ce fc 00 40 08 07:24:33.424 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 07:24:33.403 FLUSH CACHE EXT 61 00 90 00 40 00 00 3b ce fb 70 40 08 07:24:33.402 WRITE FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 23369 hours (973 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 72 0a 91 98 40 00 Error: UNC at LBA = 0x720a9198 = 1913295256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 c8 00 00 72 0a 91 98 40 08 07:24:30.206 READ FPDMA QUEUED 61 00 20 00 c0 00 00 6b ae 8e 08 40 08 07:24:30.206 WRITE FPDMA QUEUED 61 00 08 00 b8 00 00 01 85 41 4f 40 08 07:24:30.206 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 07:24:30.181 FLUSH CACHE EXT 61 00 28 00 a8 00 00 01 85 41 27 40 08 07:24:30.181 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 23369 hours (973 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 72 0a 91 98 40 00 Error: UNC at LBA = 0x720a9198 = 1913295256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 72 0a 91 98 40 08 07:24:27.056 READ FPDMA QUEUED 60 00 08 00 38 00 00 72 0a 91 28 40 08 07:24:27.055 READ FPDMA QUEUED 60 00 08 00 30 00 00 72 0a 91 38 40 08 07:24:27.054 READ FPDMA QUEUED 60 00 08 00 28 00 00 72 0a 91 10 40 08 07:24:27.053 READ FPDMA QUEUED 60 00 08 00 20 00 00 72 0a 91 e0 40 08 07:24:27.052 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 23368 hours (973 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 72 0a 91 98 40 00 Error: UNC at LBA = 0x720a9198 = 1913295256 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 28 00 00 72 0a 91 98 40 08 06:56:30.420 READ FPDMA QUEUED 60 00 08 00 20 00 00 72 0a 91 28 40 08 06:56:30.420 READ FPDMA QUEUED 60 00 08 00 18 00 00 72 0a 91 38 40 08 06:56:30.419 READ FPDMA QUEUED 60 00 08 00 10 00 00 72 0a 91 10 40 08 06:56:30.418 READ FPDMA QUEUED 60 00 08 00 08 00 00 72 0a 91 e0 40 08 06:56:30.417 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 14135 - # 2 Extended offline Completed without error 00% 12605 - # 3 Extended offline Completed without error 00% 4291 - # 4 Extended offline Completed without error 00% 3534 - # 5 Extended offline Completed without error 00% 3187 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 39/42 Celsius Lifetime Min/Max Temperature: 41/55 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (428) Index Estimated Time Temperature Celsius 429 2017-03-22 07:57 40 ********************* ... ..( 3 skipped). .. ********************* 433 2017-03-22 08:01 40 ********************* 434 2017-03-22 08:02 ? - 435 2017-03-22 08:03 41 ********************** 436 2017-03-22 08:04 40 ********************* 437 2017-03-22 08:05 40 ********************* 438 2017-03-22 08:06 ? - 439 2017-03-22 08:07 41 ********************** 440 2017-03-22 08:08 40 ********************* ... ..( 4 skipped). .. ********************* 445 2017-03-22 08:13 40 ********************* 446 2017-03-22 08:14 39 ******************** 447 2017-03-22 08:15 39 ******************** 448 2017-03-22 08:16 39 ******************** 449 2017-03-22 08:17 40 ********************* 450 2017-03-22 08:18 39 ******************** 451 2017-03-22 08:19 40 ********************* ... ..( 7 skipped). .. ********************* 459 2017-03-22 08:27 40 ********************* 460 2017-03-22 08:28 41 ********************** ... ..( 40 skipped). .. ********************** 23 2017-03-22 09:09 41 ********************** 24 2017-03-22 09:10 42 *********************** ... ..( 18 skipped). .. *********************** 43 2017-03-22 09:29 42 *********************** 44 2017-03-22 09:30 41 ********************** 45 2017-03-22 09:31 42 *********************** 46 2017-03-22 09:32 42 *********************** 47 2017-03-22 09:33 42 *********************** 48 2017-03-22 09:34 41 ********************** ... ..( 14 skipped). .. ********************** 63 2017-03-22 09:49 41 ********************** 64 2017-03-22 09:50 42 *********************** 65 2017-03-22 09:51 41 ********************** ... ..(165 skipped). .. ********************** 231 2017-03-22 12:37 41 ********************** 232 2017-03-22 12:38 ? - 233 2017-03-22 12:39 30 *********** 234 2017-03-22 12:40 30 *********** 235 2017-03-22 12:41 30 *********** 236 2017-03-22 12:42 31 ************ 237 2017-03-22 12:43 32 ************* ... ..( 2 skipped). .. ************* 240 2017-03-22 12:46 32 ************* 241 2017-03-22 12:47 33 ************** 242 2017-03-22 12:48 33 ************** 243 2017-03-22 12:49 34 *************** 244 2017-03-22 12:50 34 *************** 245 2017-03-22 12:51 34 *************** 246 2017-03-22 12:52 35 **************** ... ..( 4 skipped). .. **************** 251 2017-03-22 12:57 35 **************** 252 2017-03-22 12:58 36 ***************** ... ..( 2 skipped). .. ***************** 255 2017-03-22 13:01 36 ***************** 256 2017-03-22 13:02 37 ****************** ... ..( 2 skipped). .. ****************** 259 2017-03-22 13:05 37 ****************** 260 2017-03-22 13:06 38 ******************* ... ..( 4 skipped). .. ******************* 265 2017-03-22 13:11 38 ******************* 266 2017-03-22 13:12 39 ******************** ... ..( 5 skipped). .. ******************** 272 2017-03-22 13:18 39 ******************** 273 2017-03-22 13:19 40 ********************* ... ..( 14 skipped). .. ********************* 288 2017-03-22 13:34 40 ********************* 289 2017-03-22 13:35 41 ********************** ... ..(102 skipped). .. ********************** 392 2017-03-22 15:18 41 ********************** 393 2017-03-22 15:19 ? - 394 2017-03-22 15:20 33 ************** 395 2017-03-22 15:21 33 ************** 396 2017-03-22 15:22 34 *************** 397 2017-03-22 15:23 35 **************** ... ..( 2 skipped). .. **************** 400 2017-03-22 15:26 35 **************** 401 2017-03-22 15:27 36 ***************** ... ..( 4 skipped). .. ***************** 406 2017-03-22 15:32 36 ***************** 407 2017-03-22 15:33 37 ****************** ... ..( 3 skipped). .. ****************** 411 2017-03-22 15:37 37 ****************** 412 2017-03-22 15:38 38 ******************* ... ..( 2 skipped). .. ******************* 415 2017-03-22 15:41 38 ******************* 416 2017-03-22 15:42 39 ******************** ... ..( 6 skipped). .. ******************** 423 2017-03-22 15:49 39 ******************** 424 2017-03-22 15:50 40 ********************* 425 2017-03-22 15:51 40 ********************* 426 2017-03-22 15:52 39 ******************** 427 2017-03-22 15:53 40 ********************* 428 2017-03-22 15:54 40 ********************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 5606 Vendor specific /dev/sdd === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT Device Model: SAMSUNG HD753LJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: 1AA01113 User Capacity: 750 156 374 016 bytes [750 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Wed Mar 22 15:54:40 2017 +10 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 22) The self-test routine was aborted by the host. Total time to complete Offline data collection: (12008) seconds. Offline data collection capabilities: (0x7f) SMART execute Offline immediate. Auto Offline data collection on/off support. Abort Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 201) minutes. Conveyance self-test routine recommended polling time: ( 21) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 079 079 011 - 7130 4 Start_Stop_Count -O--CK 095 095 000 - 5464 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 100 100 051 - 0 8 Seek_Time_Performance P-S--K 100 098 015 - 13599 9 Power_On_Hours -O--CK 094 094 000 - 31887 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5464 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 0 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 064 047 000 - 36 (Min/Max 35/36) 194 Temperature_Celsius -O---K 063 046 000 - 37 (Min/Max 35/37) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 24823 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 0 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 60% 31846 - # 2 Extended offline Aborted by host 00% 31754 - # 3 Extended offline Aborted by host 30% 31650 - # 4 Extended offline Aborted by host 80% 31541 - # 5 Extended offline Aborted by host 90% 31441 - # 6 Extended offline Aborted by host 20% 31345 - # 7 Extended offline Aborted by host 50% 31140 - # 8 Extended offline Aborted by host 40% 31035 - # 9 Extended offline Aborted by host 30% 30939 - #10 Extended offline Aborted by host 70% 30688 - #11 Extended offline Aborted by host 10% 30600 - #12 Extended offline Aborted by host 60% 30380 - #13 Extended offline Aborted by host 80% 30222 - #14 Extended offline Aborted by host 10% 29536 - #15 Extended offline Aborted by host 40% 29354 - #16 Extended offline Aborted by host 10% 29316 - #17 Extended offline Aborted by host 10% 29233 - #18 Extended offline Aborted by host 50% 29064 - #19 Extended offline Aborted by host 30% 28952 - #20 Extended offline Aborted by host 50% 28878 - #21 Extended offline Aborted by host 90% 28793 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Max Temperature: 37 Celsius Lifetime Max Temperature: 58 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (18) Index Estimated Time Temperature Celsius 19 2017-03-22 13:47 33 ************** 20 2017-03-22 13:48 34 *************** ... ..( 8 skipped). .. *************** 29 2017-03-22 13:57 34 *************** 30 2017-03-22 13:58 35 **************** 31 2017-03-22 13:59 ? - 32 2017-03-22 14:00 35 **************** 33 2017-03-22 14:01 ? - 34 2017-03-22 14:02 35 **************** 35 2017-03-22 14:03 35 **************** 36 2017-03-22 14:04 36 ***************** ... ..( 56 skipped). .. ***************** 93 2017-03-22 15:01 36 ***************** 94 2017-03-22 15:02 37 ****************** 95 2017-03-22 15:03 36 ***************** 96 2017-03-22 15:04 36 ***************** 97 2017-03-22 15:05 37 ****************** 98 2017-03-22 15:06 36 ***************** ... ..( 4 skipped). .. ***************** 103 2017-03-22 15:11 36 ***************** 104 2017-03-22 15:12 37 ****************** ... ..( 4 skipped). .. ****************** 109 2017-03-22 15:17 37 ****************** 110 2017-03-22 15:18 36 ***************** 111 2017-03-22 15:19 37 ****************** 112 2017-03-22 15:20 37 ****************** 113 2017-03-22 15:21 37 ****************** 114 2017-03-22 15:22 36 ***************** 115 2017-03-22 15:23 37 ****************** 116 2017-03-22 15:24 36 ***************** 117 2017-03-22 15:25 36 ***************** 118 2017-03-22 15:26 37 ****************** ... ..( 2 skipped). .. ****************** 121 2017-03-22 15:29 37 ****************** 122 2017-03-22 15:30 36 ***************** 123 2017-03-22 15:31 37 ****************** ... ..( 22 skipped). .. ****************** 18 2017-03-22 15:54 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 31 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 31 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC