/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.11.0-46-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST750LM022 HN-M750MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2AR10002 User Capacity: 750,156,374,016 bytes [750 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Jan 12 18:24:29 2022 AWST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9720) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 162) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 256 2 Throughput_Performance POS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 089 087 025 - 3454 4 Start_Stop_Count -O--CK 096 096 000 - 4993 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-K 252 252 051 - 0 8 Seek_Time_Performance P-S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 11110 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 913 12 Power_Cycle_Count -O--CK 096 096 000 - 4948 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 5450111 183 Runtime_Bad_Block -O--CK 252 252 010 - 0 184 End-to-End_Error PO--CK 252 252 048 - 0 186 Unknown_Attribute -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 12 188 Command_Timeout -O--CK 100 100 000 - 12 190 Airflow_Temperature_Cel -O---- 062 031 040 Past 38 (Min/Max 10/69) 191 G-Sense_Error_Rate -O---K 100 100 000 - 278 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 193 Load_Cycle_Count -O--CK 081 081 000 - 198611 194 Temperature_Celsius -O---- 062 031 000 - 38 (Min/Max 10/69) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 001 001 000 - 80418 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 12 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12 [3] occurred at disk power-on lifetime: 10740 hours (447 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 a8 10 00 00 00 00 00 00 e0 00 Error: UNC 43024 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 00 18 a8 00 e0 00 00:00:00.011 READ DMA EXT 25 00 00 00 20 00 00 00 00 00 02 e0 00 00:00:00.011 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 01 e0 00 00:00:00.011 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 01 e0 00 00:00:00.011 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:00:00.009 READ DMA EXT Error 11 [2] occurred at disk power-on lifetime: 10686 hours (445 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 a8 01 00 00 00 00 00 00 e0 00 Error: UNC 43009 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 01 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 0c a3 fe e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 00 e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 00 e0 00 00:00:00.003 READ DMA EXT Error 10 [1] occurred at disk power-on lifetime: 10246 hours (426 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 a8 01 00 00 00 00 00 00 e0 00 Error: UNC 43009 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 01 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 0c a3 fe e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 00 e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 00 e0 00 00:00:00.003 READ DMA EXT Error 9 [0] occurred at disk power-on lifetime: 9978 hours (415 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 a8 01 00 00 00 00 00 00 e0 00 Error: UNC 43009 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 01 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 0c a3 fe e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 00 e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 00 e0 00 00:00:00.003 READ DMA EXT Error 8 [7] occurred at disk power-on lifetime: 9976 hours (415 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 a8 01 00 00 00 00 00 00 e0 00 Error: UNC 43009 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 18 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.003 READ DMA EXT Error 7 [6] occurred at disk power-on lifetime: 9888 hours (412 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 a8 01 00 00 00 00 00 00 e0 00 Error: UNC 43009 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 01 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 0c a3 fe e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 00 e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 00 e0 00 00:00:00.003 READ DMA EXT Error 6 [5] occurred at disk power-on lifetime: 9567 hours (398 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 a8 01 00 00 00 00 00 00 e0 00 Error: UNC 43009 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 01 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 0c a3 fe e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 00 e0 00 00:00:00.003 READ DMA EXT 25 00 00 00 01 00 00 00 0c 88 00 e0 00 00:00:00.003 READ DMA EXT Error 5 [4] occurred at disk power-on lifetime: 9155 hours (381 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 a8 01 00 00 00 00 00 00 e0 00 Error: UNC 43009 sectors at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 18 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.005 READ DMA EXT 25 00 00 00 01 00 00 00 14 a8 00 e0 00 00:00:00.003 READ DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 10942 - # 2 Short offline Completed without error 00% 6301 - # 3 Short offline Completed without error 00% 6084 - # 4 Short offline Completed without error 00% 5927 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 26/40 Celsius Lifetime Min/Max Temperature: 11/69 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (16) Index Estimated Time Temperature Celsius 17 2022-01-12 07:45 38 ******************* 18 2022-01-12 07:50 33 ************** ... ..( 9 skipped). .. ************** 28 2022-01-12 08:40 33 ************** 29 2022-01-12 08:45 32 ************* ... ..( 48 skipped). .. ************* 78 2022-01-12 12:50 32 ************* 79 2022-01-12 12:55 31 ************ 80 2022-01-12 13:00 32 ************* 81 2022-01-12 13:05 31 ************ 82 2022-01-12 13:10 32 ************* 83 2022-01-12 13:15 32 ************* 84 2022-01-12 13:20 31 ************ ... ..( 36 skipped). .. ************ 121 2022-01-12 16:25 31 ************ 122 2022-01-12 16:30 32 ************* 123 2022-01-12 16:35 33 ************** 124 2022-01-12 16:40 32 ************* 125 2022-01-12 16:45 32 ************* 126 2022-01-12 16:50 32 ************* 127 2022-01-12 16:55 31 ************ ... ..( 6 skipped). .. ************ 6 2022-01-12 17:30 31 ************ 7 2022-01-12 17:35 30 *********** 8 2022-01-12 17:40 31 ************ 9 2022-01-12 17:45 33 ************** 10 2022-01-12 17:50 34 *************** 11 2022-01-12 17:55 34 *************** 12 2022-01-12 18:00 37 ****************** 13 2022-01-12 18:05 40 ********************* 14 2022-01-12 18:10 38 ******************* 15 2022-01-12 18:15 37 ****************** 16 2022-01-12 18:20 38 ******************* SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 4154 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 8 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific