/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.5-200.fc31.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital VelociRaptor Device Model: WDC WD1500HLFS-01G6U3 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 04.04V05 User Capacity: 150,039,945,216 bytes [150 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 10000 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sat Feb 22 23:05:42 2020 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 32) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 0 3 Spin_Up_Time PO---- 199 192 021 - 3016 4 Start_Stop_Count -O--CK 097 097 000 - 3794 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 000 - 0 9 Power_On_Hours -O--CK 047 047 000 - 39156 10 Spin_Retry_Count -O--C- 100 100 000 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3773 192 Power-Off_Retract_Count -O--CK 200 200 000 - 622 193 Load_Cycle_Count -O--CK 199 199 000 - 3795 194 Temperature_Celsius -O---K 113 098 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 8 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 8 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 b0 60 00 5a 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 01 00 00 00 00 47 00 40 40 00 00 08 00:00:00.112 DEVICE RESET 00 33 ec 00 40 00 00 08 00 00 00 00 00 00:00:16.455 NOP [Reserved subcommand] [OBS-ACS-2] 0a 46 03 00 00 00 31 00 40 ef 00 00 0a 00:00:00.000 [RESERVED] Error 7 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 01 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 6b 60 ac 48 00 00 00 00 00 00 00 0c 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 68 10 00 b0 ac 59 0c 48 60 00 00 08 00:00:08.312 DEVICE RESET 0c 58 60 ac 48 00 68 08 b0 10 00 00 0c 03:08:10.712 [RESERVED] 08 50 40 00 d0 ac 58 10 48 60 00 00 08 00:00:45.160 DEVICE RESET Error 6 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 01 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 22 60 04 43 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 40 00 ca 04 1e 00 43 60 00 00 08 00:00:28.672 DEVICE RESET 00 13 60 04 43 00 00 08 b0 08 00 00 00 00:04:39.320 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 40 00 d2 04 12 00 43 60 00 00 08 00:00:24.576 DEVICE RESET Error 5 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 01 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 9d 60 c6 d8 00 00 00 00 00 00 00 05 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 1b 00 5b c6 9a 00 d8 60 00 00 08 00:00:00.008 DEVICE RESET 00 89 60 c6 d8 00 00 08 5b 3a 00 00 05 03:37:11.572 NOP [Reserved subcommand] [OBS-ACS-2] 08 10 00 00 78 c6 89 05 d8 60 00 00 08 00:00:30.736 DEVICE RESET Error 4 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 01 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 a3 60 01 63 00 00 00 00 00 00 00 10 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 50 00 a0 01 97 10 63 60 00 00 08 00:00:47.104 DEVICE RESET 0f 6c 60 01 63 00 00 08 70 58 00 00 0f 00:01:31.015 [RESERVED] 08 08 02 00 c0 01 67 00 63 60 00 00 08 00:00:38.952 DEVICE RESET Error 3 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 15 61 3f 12 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 08 00 78 3f 14 00 12 61 00 00 08 00:01:01.440 DEVICE RESET 03 62 61 3f 06 00 28 08 e0 70 00 00 03 01:08:50.402 CFA REQUEST EXTENDED ERROR 08 28 70 00 e0 3f 62 03 06 61 00 00 08 00:00:57.384 DEVICE RESET Error 2 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 b5 61 39 88 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 10 00 10 39 cb 00 7d 61 00 00 08 00:00:20.480 DEVICE RESET 00 cb 61 39 7d 00 00 08 f8 10 00 00 00 01:02:47.755 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 08 00 80 39 ca 00 7d 61 00 00 08 00:00:40.960 DEVICE RESET Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 00 01 01 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c7 61 2c 84 00 00 00 00 00 00 00 02 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 00 08 00 28 2c 64 06 74 61 00 00 08 00:00:57.344 DEVICE RESET 02 a7 61 2c 69 00 08 08 e0 da 00 00 02 00:48:30.646 [RESERVED] 08 00 08 00 08 2c ae 00 60 61 00 00 08 00:00:57.352 DEVICE RESET SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 33088 - # 2 Short offline Completed without error 00% 33087 - # 3 Extended offline Completed without error 00% 22164 - # 4 Conveyance offline Completed without error 00% 22091 - # 5 Extended offline Completed without error 00% 22090 - # 6 Conveyance offline Completed without error 00% 902 - # 7 Short offline Completed without error 00% 902 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 21/36 Celsius Lifetime Min/Max Temperature: 22/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (54) Index Estimated Time Temperature Celsius 55 2020-02-22 20:58 34 *************** ... ..( 28 skipped). .. *************** 84 2020-02-22 21:27 34 *************** 85 2020-02-22 21:28 35 **************** ... ..( 16 skipped). .. **************** 102 2020-02-22 21:45 35 **************** 103 2020-02-22 21:46 36 ***************** ... ..( 36 skipped). .. ***************** 12 2020-02-22 22:23 36 ***************** 13 2020-02-22 22:24 35 **************** ... ..( 13 skipped). .. **************** 27 2020-02-22 22:38 35 **************** 28 2020-02-22 22:39 34 *************** ... ..( 25 skipped). .. *************** 54 2020-02-22 23:05 34 *************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 1 R_ERR response for non-data FIS 0x0006 2 1 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x8000 4 30416 Vendor specific /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.5-200.fc31.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Black Device Model: WDC WD1001FALS-00E8B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 05.00K05 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sat Feb 22 23:05:42 2020 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (18600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 214) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 253 253 021 - 1183 4 Start_Stop_Count -O--CK 096 096 000 - 4031 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 042 042 000 - 43009 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4012 192 Power-Off_Retract_Count -O--CK 198 198 000 - 1788 193 Load_Cycle_Count -O--CK 200 200 000 - 2242 194 Temperature_Celsius -O---K 113 098 000 - 37 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 199 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 13774 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13774 [21] occurred at disk power-on lifetime: 42782 hours (1782 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 08 69 00 95 df 40 00 Error: UNC at LBA = 0x8690095df = 36121384415 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 08 00 00 70 00 00 08 95 64 00 40 08 23:52:14.279 READ FPDMA QUEUED 60 04 00 00 a8 00 00 08 95 60 00 40 08 23:52:14.254 READ FPDMA QUEUED 60 08 00 00 68 00 00 08 95 58 00 40 08 23:52:14.236 READ FPDMA QUEUED 60 01 48 00 60 00 00 08 95 84 00 40 08 23:52:14.211 READ FPDMA QUEUED 60 04 00 00 a0 00 00 08 95 80 00 40 08 23:52:14.166 READ FPDMA QUEUED Error 13773 [20] occurred at disk power-on lifetime: 42775 hours (1782 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 08 69 00 95 df 40 00 Error: UNC at LBA = 0x8690095df = 36121384415 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 08 00 00 40 00 00 08 95 64 00 40 08 16:31:50.709 READ FPDMA QUEUED 60 04 00 00 38 00 00 08 95 60 00 40 08 16:31:50.704 READ FPDMA QUEUED 60 08 00 00 30 00 00 08 95 58 00 40 08 16:31:50.690 READ FPDMA QUEUED 60 01 48 00 28 00 00 08 95 84 00 40 08 16:31:50.687 READ FPDMA QUEUED 60 04 00 00 20 00 00 08 95 80 00 40 08 16:31:50.674 READ FPDMA QUEUED Error 13772 [19] occurred at disk power-on lifetime: 42568 hours (1773 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 08 52 00 95 85 40 00 Error: UNC at LBA = 0x852009585 = 35735508357 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 d8 00 00 08 95 52 80 40 08 03:10:55.038 READ FPDMA QUEUED 60 00 08 00 d0 00 00 08 95 52 78 40 08 03:10:55.038 READ FPDMA QUEUED 60 00 08 00 c8 00 00 08 95 52 70 40 08 03:10:55.038 READ FPDMA QUEUED 60 00 08 00 c0 00 00 08 95 52 68 40 08 03:10:55.038 READ FPDMA QUEUED 60 00 08 00 b8 00 00 22 5e d4 08 40 08 03:10:55.038 READ FPDMA QUEUED Error 13771 [18] occurred at disk power-on lifetime: 42568 hours (1773 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 08 52 00 95 85 40 00 Error: UNC at LBA = 0x852009585 = 35735508357 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 a0 00 00 08 ce 99 e0 40 08 03:10:51.872 READ FPDMA QUEUED 60 01 00 00 98 00 00 08 95 51 e0 40 08 03:10:51.872 READ FPDMA QUEUED 60 01 00 00 90 00 00 08 ce a8 e0 40 08 03:10:51.871 READ FPDMA QUEUED 60 00 80 00 88 00 00 08 ce a8 60 40 08 03:10:51.871 READ FPDMA QUEUED 60 00 40 00 80 00 00 08 ce a8 20 40 08 03:10:51.870 READ FPDMA QUEUED Error 13770 [17] occurred at disk power-on lifetime: 40008 hours (1667 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 08 47 00 7e 00 40 00 Error: UNC 256 sectors at LBA = 0x847007e00 = 35550952960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 d0 ff 01 00 00 00 08 7e 47 00 40 08 12:53:36.459 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 46 00 40 08 12:53:36.459 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 45 00 40 08 12:53:36.458 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 44 00 40 08 12:53:36.458 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 43 00 40 08 12:53:36.457 READ DMA EXT Error 13769 [16] occurred at disk power-on lifetime: 40008 hours (1667 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 08 47 00 7e 00 40 00 Error: UNC 256 sectors at LBA = 0x847007e00 = 35550952960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 d0 ff 01 00 00 00 08 7e 47 00 40 08 12:51:02.031 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 46 00 40 08 12:51:02.030 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 45 00 40 08 12:51:02.030 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 44 00 40 08 12:51:02.029 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 43 00 40 08 12:51:02.029 READ DMA EXT Error 13768 [15] occurred at disk power-on lifetime: 40007 hours (1666 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 08 47 00 7e 00 40 00 Error: UNC 256 sectors at LBA = 0x847007e00 = 35550952960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 d0 ff 01 00 00 00 08 7e 47 00 40 08 12:38:15.685 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 46 00 40 08 12:38:15.684 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 45 00 40 08 12:38:15.684 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 44 00 40 08 12:38:15.683 READ DMA EXT 25 d0 ff 01 00 00 00 08 7e 43 00 40 08 12:38:15.683 READ DMA EXT Error 13767 [14] occurred at disk power-on lifetime: 37557 hours (1564 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 30 00 71 16 40 00 Error: UNC at LBA = 0x30007116 = 805335318 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 02 00 00 00 00 00 71 30 16 40 00 00:46:43.469 READ FPDMA QUEUED 61 00 08 00 00 00 00 1f ac 85 b8 40 00 00:46:42.538 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 1f ac 85 c0 40 00 00:46:42.538 WRITE FPDMA QUEUED 2f 02 00 00 01 00 00 00 00 00 10 40 00 00:46:42.470 READ LOG EXT 60 00 02 00 00 00 00 00 71 30 16 40 00 00:46:40.056 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed: read failure 90% 36939 142480075 # 2 Short offline Completed: read failure 90% 36939 142480075 # 3 Short offline Completed: read failure 90% 36939 142480075 # 4 Short offline Completed without error 00% 76 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 22/38 Celsius Lifetime Min/Max Temperature: 22/52 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (121) Index Estimated Time Temperature Celsius 122 2020-02-22 20:58 37 ****************** ... ..( 44 skipped). .. ****************** 39 2020-02-22 21:43 37 ****************** 40 2020-02-22 21:44 38 ******************* ... ..( 52 skipped). .. ******************* 93 2020-02-22 22:37 38 ******************* 94 2020-02-22 22:38 37 ****************** ... ..( 26 skipped). .. ****************** 121 2020-02-22 23:05 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 1 R_ERR response for non-data FIS 0x0006 2 1 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x8000 4 30406 Vendor specific /dev/sdc smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.5-200.fc31.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar SE Device Model: WDC WD400JB-00FMA0 Serial Number: -- Firmware Version: 13.03G13 User Capacity: 40,020,664,320 bytes [40.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 (minor revision not indicated) Local Time is: Sat Feb 22 23:05:43 2020 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1260) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 23) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 200 200 051 - 0 3 Spin_Up_Time POS--- 103 098 021 - 2208 4 Start_Stop_Count -O--CK 096 096 040 - 4599 5 Reallocated_Sector_Ct PO--CK 198 198 140 - 14 7 Seek_Error_Rate PO-R-- 200 198 051 - 0 9 Power_On_Hours -O--CK 062 062 000 - 27844 10 Spin_Retry_Count PO--C- 100 100 051 - 0 11 Calibration_Retry_Count PO--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3291 194 Temperature_Celsius -O---K 110 000 000 - 33 196 Reallocated_Event_Count -O--CK 198 198 000 - 2 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable -O--C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: scsi error badly formed scsi parameters General Purpose Log Directory not supported SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 No Errors Logged SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Fatal or unknown error 90% 20905 4293918720 # 2 Short offline Fatal or unknown error 90% 20903 4293918720 # 3 Short offline Fatal or unknown error 90% 20763 4293918720 # 4 Conveyance offline Fatal or unknown error 90% 18064 4293918720 # 5 Conveyance offline Fatal or unknown error 90% 18063 4293918720 # 6 Short offline Fatal or unknown error 90% 18040 4293918720 # 7 Conveyance offline Fatal or unknown error 90% 17941 4293918720 # 8 Conveyance offline Fatal or unknown error 90% 17941 4293918720 # 9 Conveyance offline Fatal or unknown error 90% 17940 4293918720 #10 Conveyance offline Fatal or unknown error 90% 17908 4293918720 #11 Extended offline Fatal or unknown error 90% 17908 4293918720 #12 Short offline Fatal or unknown error 90% 17908 4293918720 #13 Conveyance offline Fatal or unknown error 90% 17162 4293918720 #14 Conveyance offline Fatal or unknown error 90% 17162 4293918720 #15 Conveyance offline Fatal or unknown error 90% 17161 4293918720 #16 Conveyance offline Fatal or unknown error 90% 17161 4293918720 #17 Conveyance offline Fatal or unknown error 90% 17161 4293918720 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdd smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.5-200.fc31.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000.B Device Model: Hitachi HDT721016SLA380 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: ST1OA31B User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Feb 22 23:05:43 2020 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 128 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2371) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 100 100 054 - 0 3 Spin_Up_Time POS--- 121 121 024 - 229 (Average 183) 4 Start_Stop_Count -O--C- 100 100 000 - 3113 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 8 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 020 - 0 9 Power_On_Hours -O--C- 098 098 000 - 18347 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 2995 192 Power-Off_Retract_Count -O--CK 097 097 000 - 3778 193 Load_Cycle_Count -O--C- 097 097 000 - 3778 194 Temperature_Celsius -O---- 176 176 000 - 34 (Min/Max 9/49) 196 Reallocated_Event_Count -O--CK 100 100 000 - 8 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 5372 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5372 [3] occurred at disk power-on lifetime: 10585 hours (441 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 31 00 00 00 a9 dc ee e0 00 Error: UNC 49 sectors at LBA = 0x00a9dcee = 11132142 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 a9 dc df e0 00 01:46:02.500 READ DMA EXT 25 00 00 00 40 00 00 00 a9 dc 9f e0 00 01:46:02.400 READ DMA EXT 25 00 00 00 2e 00 00 00 83 86 1f e0 00 01:46:02.400 READ DMA EXT 25 00 00 00 3c 00 00 05 e4 25 b7 e0 00 01:46:02.400 READ DMA EXT 25 00 00 00 40 00 00 05 e4 15 07 e0 00 01:46:02.400 READ DMA EXT Error 5371 [2] occurred at disk power-on lifetime: 9420 hours (392 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 31 00 00 00 a9 dc ee e0 00 Error: UNC 49 sectors at LBA = 0x00a9dcee = 11132142 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 a9 dc df e0 00 1d+07:06:49.100 READ DMA EXT 25 00 00 00 40 00 00 00 a9 dc 9f e0 00 1d+07:06:49.100 READ DMA EXT 25 00 00 00 08 00 00 00 83 86 1f e0 00 1d+07:06:49.100 READ DMA EXT 25 00 00 00 08 00 00 05 e4 15 07 e0 00 1d+07:06:49.100 READ DMA EXT 25 00 00 00 3c 00 00 00 83 85 a7 e0 00 1d+07:06:49.100 READ DMA EXT Error 5370 [1] occurred at disk power-on lifetime: 9414 hours (392 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 31 00 00 00 a9 dc ee e0 00 Error: UNC 49 sectors at LBA = 0x00a9dcee = 11132142 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 a9 dc df e0 00 1d+01:37:20.100 READ DMA EXT 25 00 00 00 40 00 00 00 a9 dc 9f e0 00 1d+01:37:20.100 READ DMA EXT 25 00 00 00 08 00 00 00 83 86 1f e0 00 1d+01:37:20.100 READ DMA EXT 25 00 00 00 40 00 00 05 e4 15 07 e0 00 1d+01:37:20.000 READ DMA EXT 25 00 00 00 30 00 00 00 83 85 77 e0 00 1d+01:37:20.000 READ DMA EXT Error 5369 [0] occurred at disk power-on lifetime: 9123 hours (380 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 21 00 00 00 a9 dc ee e0 00 Error: UNC 33 sectors at LBA = 0x00a9dcee = 11132142 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 48 00 00 00 a9 dc c7 e0 00 03:22:25.300 READ DMA EXT 25 00 00 00 80 00 00 00 a9 dc 47 e0 00 03:22:25.300 READ DMA EXT 25 00 00 00 10 00 00 00 a9 db df e0 00 03:22:25.200 READ DMA EXT 25 00 00 00 10 00 00 00 ab 21 7f e0 00 03:22:25.200 READ DMA EXT 25 00 00 00 40 00 00 00 ab 21 2f e0 00 03:22:25.200 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 16009 - # 2 Short offline Completed without error 00% 16008 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 24/36 Celsius Lifetime Min/Max Temperature: 9/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (29) Index Estimated Time Temperature Celsius 30 2020-02-22 20:58 34 *************** ... ..( 14 skipped). .. *************** 45 2020-02-22 21:13 34 *************** 46 2020-02-22 21:14 35 **************** ... ..( 23 skipped). .. **************** 70 2020-02-22 21:38 35 **************** 71 2020-02-22 21:39 36 ***************** 72 2020-02-22 21:40 36 ***************** 73 2020-02-22 21:41 35 **************** 74 2020-02-22 21:42 36 ***************** ... ..( 36 skipped). .. ***************** 111 2020-02-22 22:19 36 ***************** 112 2020-02-22 22:20 35 **************** ... ..( 9 skipped). .. **************** 122 2020-02-22 22:30 35 **************** 123 2020-02-22 22:31 34 *************** ... ..( 33 skipped). .. *************** 29 2020-02-22 23:05 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sde smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.5-200.fc31.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: WD Blue and Green SSDs Device Model: WDC WDS120G2G0A-00JH30 Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: UE500000 User Capacity: 120,040,980,480 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Feb 22 23:05:44 2020 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x15) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 21) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 2952 12 Power_Cycle_Count -O--CK 100 100 000 - 366 165 Block_Erase_Count -O--CK 100 100 000 - 571 166 Minimum_PE_Cycles_TLC -O--CK 100 100 --- - 6 167 Max_Bad_Blocks_per_Die -O--CK 100 100 --- - 0 168 Maximum_PE_Cycles_TLC -O--CK 100 100 --- - 16 169 Total_Bad_Blocks -O--CK 100 100 --- - 112 170 Grown_Bad_Blocks -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Average_PE_Cycles_TLC -O--CK 100 100 000 - 6 174 Unexpected_Power_Loss -O--CK 100 100 000 - 118 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 078 034 000 - 22 (Min/Max 0/34) 199 UDMA_CRC_Error_Count -O--CK 100 100 --- - 0 230 Media_Wearout_Indicator -O--CK 100 100 000 - 0x013f0114013f 232 Available_Reservd_Space PO--CK 100 100 005 - 100 233 NAND_GB_Written_TLC -O--CK 100 100 --- - 664 234 NAND_GB_Written_SLC -O--CK 100 100 000 - 3181 241 Host_Writes_GiB ----CK 100 100 000 - 1290 242 Host_Reads_GiB ----CK 100 100 000 - 1848 244 Temp_Throttle_Status -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log 0xa7 GPL,SL VS 1 Device vendor specific log 0xa9 GPL,SL VS 3 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 366 --- Lifetime Power-On Resets 0x01 0x010 4 2952 --- Power-on Hours 0x01 0x018 6 2706095753 --- Logical Sectors Written 0x01 0x028 6 3875777521 --- Logical Sectors Read 0x01 0x038 6 2953 --- Date and Time TimeStamp 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 22 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 12 --- Lowest Temperature 0x05 0x030 1 25 --- Highest Average Short Term Temperature 0x05 0x038 1 25 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error /dev/sdf smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.5.5-200.fc31.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD20EZRX-22D8PB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Feb 22 23:05:44 2020 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (25440) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 257) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 184 174 021 - 3775 4 Start_Stop_Count -O--CK 098 098 000 - 2154 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 076 076 000 - 18112 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2147 192 Power-Off_Retract_Count -O--CK 199 199 000 - 1231 193 Load_Cycle_Count -O--CK 161 161 000 - 119516 194 Temperature_Celsius -O---K 117 104 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 39 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 12160 - # 2 Short offline Completed without error 00% 12160 - # 3 Short offline Completed without error 00% 3 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 21/32 Celsius Lifetime Min/Max Temperature: 18/43 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (243) Index Estimated Time Temperature Celsius 244 2020-02-22 15:08 32 ************* ... ..(152 skipped). .. ************* 397 2020-02-22 17:41 32 ************* 398 2020-02-22 17:42 31 ************ ... ..( 91 skipped). .. ************ 12 2020-02-22 19:14 31 ************ 13 2020-02-22 19:15 32 ************* ... ..( 39 skipped). .. ************* 53 2020-02-22 19:55 32 ************* 54 2020-02-22 19:56 31 ************ ... ..( 9 skipped). .. ************ 64 2020-02-22 20:06 31 ************ 65 2020-02-22 20:07 30 *********** ... ..( 21 skipped). .. *********** 87 2020-02-22 20:29 30 *********** 88 2020-02-22 20:30 28 ********* ... ..( 21 skipped). .. ********* 110 2020-02-22 20:52 28 ********* 111 2020-02-22 20:53 29 ********** 112 2020-02-22 20:54 29 ********** 113 2020-02-22 20:55 29 ********** 114 2020-02-22 20:56 30 *********** ... ..( 2 skipped). .. *********** 117 2020-02-22 20:59 30 *********** 118 2020-02-22 21:00 31 ************ ... ..( 11 skipped). .. ************ 130 2020-02-22 21:12 31 ************ 131 2020-02-22 21:13 32 ************* ... ..(111 skipped). .. ************* 243 2020-02-22 23:05 32 ************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 30413 Vendor specific