/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar P7K500 Device Model: Hitachi HDP725050GLA360 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GM4OA5CA User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun May 8 23:25:07 2016 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7890) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 131) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 132 132 054 - 140 3 Spin_Up_Time POS--- 114 114 024 - 338 (Average 335) 4 Start_Stop_Count -O--C- 098 098 000 - 8112 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 131 131 020 - 29 9 Power_On_Hours -O--C- 099 099 000 - 12575 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 6152 192 Power-Off_Retract_Count -O--CK 094 094 000 - 8137 193 Load_Cycle_Count -O--C- 094 094 000 - 8137 194 Temperature_Celsius -O---- 166 166 000 - 36 (Min/Max 10/49) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 17 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 18/36 Celsius Lifetime Min/Max Temperature: 10/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (53) Index Estimated Time Temperature Celsius 54 2016-05-08 21:18 24 ***** 55 2016-05-08 21:19 25 ****** 56 2016-05-08 21:20 26 ******* 57 2016-05-08 21:21 26 ******* 58 2016-05-08 21:22 27 ******** 59 2016-05-08 21:23 28 ********* 60 2016-05-08 21:24 28 ********* 61 2016-05-08 21:25 29 ********** 62 2016-05-08 21:26 29 ********** 63 2016-05-08 21:27 29 ********** 64 2016-05-08 21:28 30 *********** 65 2016-05-08 21:29 31 ************ 66 2016-05-08 21:30 31 ************ 67 2016-05-08 21:31 31 ************ 68 2016-05-08 21:32 32 ************* ... ..( 2 skipped). .. ************* 71 2016-05-08 21:35 32 ************* 72 2016-05-08 21:36 33 ************** 73 2016-05-08 21:37 33 ************** 74 2016-05-08 21:38 33 ************** 75 2016-05-08 21:39 34 *************** ... ..( 5 skipped). .. *************** 81 2016-05-08 21:45 34 *************** 82 2016-05-08 21:46 35 **************** ... ..( 7 skipped). .. **************** 90 2016-05-08 21:54 35 **************** 91 2016-05-08 21:55 36 ***************** ... ..( 20 skipped). .. ***************** 112 2016-05-08 22:16 36 ***************** 113 2016-05-08 22:17 35 **************** 114 2016-05-08 22:18 36 ***************** 115 2016-05-08 22:19 35 **************** ... ..( 57 skipped). .. **************** 45 2016-05-08 23:17 35 **************** 46 2016-05-08 23:18 36 ***************** 47 2016-05-08 23:19 35 **************** 48 2016-05-08 23:20 36 ***************** 49 2016-05-08 23:21 35 **************** ... ..( 3 skipped). .. **************** 53 2016-05-08 23:25 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST1000DM003-1CH162 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC47 User Capacity: 1,000,204,886,016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun May 8 23:25:07 2016 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 575) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 106) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 120 099 006 - 236481304 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1848 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 078 060 030 - 64661100 9 Power_On_Hours -O--CK 096 096 000 - 3797 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1577 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 099 000 - 0 0 7 189 High_Fly_Writes -O-RCK 099 099 000 - 1 190 Airflow_Temperature_Cel -O---K 068 057 045 - 32 (Min/Max 18/34) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 224 193 Load_Cycle_Count -O--CK 090 090 000 - 21671 194 Temperature_Celsius -O---K 032 043 000 - 32 (0 12 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 2649h+02m+26.076s 241 Total_LBAs_Written ------ 100 253 000 - 10020333471 242 Total_LBAs_Read ------ 100 253 000 - 15849989180 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 18/33 Celsius Lifetime Min/Max Temperature: 12/43 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000.C Device Model: Hitachi HDS721032CLA362 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JPFOA39C User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun May 8 23:25:08 2016 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 128 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4334) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 72) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 125 125 054 - 135 3 Spin_Up_Time POS--- 116 116 024 - 198 (Average 198) 4 Start_Stop_Count -O--C- 099 099 000 - 7207 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 134 134 020 - 33 9 Power_On_Hours -O--C- 099 099 000 - 11142 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 5506 192 Power-Off_Retract_Count -O--CK 094 094 000 - 7229 193 Load_Cycle_Count -O--C- 094 094 000 - 7229 194 Temperature_Celsius -O---- 181 181 000 - 33 (Min/Max 12/49) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 0 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 19/33 Celsius Lifetime Min/Max Temperature: 12/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (51) Index Estimated Time Temperature Celsius 52 2016-05-08 21:18 24 ***** 53 2016-05-08 21:19 25 ****** 54 2016-05-08 21:20 25 ****** 55 2016-05-08 21:21 26 ******* 56 2016-05-08 21:22 26 ******* 57 2016-05-08 21:23 27 ******** 58 2016-05-08 21:24 27 ******** 59 2016-05-08 21:25 27 ******** 60 2016-05-08 21:26 28 ********* 61 2016-05-08 21:27 28 ********* 62 2016-05-08 21:28 28 ********* 63 2016-05-08 21:29 29 ********** ... ..( 2 skipped). .. ********** 66 2016-05-08 21:32 29 ********** 67 2016-05-08 21:33 30 *********** ... ..( 2 skipped). .. *********** 70 2016-05-08 21:36 30 *********** 71 2016-05-08 21:37 31 ************ ... ..( 5 skipped). .. ************ 77 2016-05-08 21:43 31 ************ 78 2016-05-08 21:44 32 ************* ... ..( 8 skipped). .. ************* 87 2016-05-08 21:53 32 ************* 88 2016-05-08 21:54 33 ************** ... ..( 22 skipped). .. ************** 111 2016-05-08 22:17 33 ************** 112 2016-05-08 22:18 32 ************* ... ..( 46 skipped). .. ************* 31 2016-05-08 23:05 32 ************* 32 2016-05-08 23:06 33 ************** 33 2016-05-08 23:07 33 ************** 34 2016-05-08 23:08 33 ************** 35 2016-05-08 23:09 32 ************* 36 2016-05-08 23:10 33 ************** ... ..( 14 skipped). .. ************** 51 2016-05-08 23:25 33 ************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Description 1 ===== = = == General Statistics (rev 1) == 1 0x008 4 5506 Lifetime Power-On Resets 1 0x010 4 11142 Power-on Hours 1 0x018 6 15923006013 Logical Sectors Written 1 0x020 6 207670916 Number of Write Commands 1 0x028 6 129637217497 Logical Sectors Read 1 0x030 6 354906865 Number of Read Commands 3 ===== = = == Rotating Media Statistics (rev 1) == 3 0x008 4 9656 Spindle Motor Power-on Hours 3 0x010 4 9656 Head Flying Hours 3 0x018 4 7229 Head Load Events 3 0x020 4 0 Number of Reallocated Logical Sectors 3 0x028 4 1 Read Recovery Attempts 3 0x030 4 4294967295 Number of Mechanical Start Failures 4 ===== = = == General Errors Statistics (rev 1) == 4 0x008 4 0 Number of Reported Uncorrectable Errors 4 0x010 4 9860 Resets Between Cmd Acceptance and Completion 5 ===== = = == Temperature Statistics (rev 1) == 5 0x008 1 33 Current Temperature 5 0x010 1 29~ Average Short Term Temperature 5 0x018 1 28~ Average Long Term Temperature 5 0x020 1 49 Highest Temperature 5 0x028 1 12 Lowest Temperature 5 0x030 1 43~ Highest Average Short Term Temperature 5 0x038 1 0~ Lowest Average Short Term Temperature 5 0x040 1 40~ Highest Average Long Term Temperature 5 0x048 1 0~ Lowest Average Long Term Temperature 5 0x050 4 0 Time in Over-Temperature 5 0x058 1 60 Specified Maximum Operating Temperature 5 0x060 4 0 Time in Under-Temperature 5 0x068 1 0 Specified Minimum Operating Temperature 6 ===== = = == Transport Statistics (rev 1) == 6 0x008 4 32674 Number of Hardware Resets 6 0x010 4 17628 Number of ASR Events 6 0x018 4 0 Number of Interface CRC Errors |_ ~ normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0009 2 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdd === START OF INFORMATION SECTION === Model Family: Maxtor Fireball 3 Device Model: Maxtor 2F040L0 Serial Number: -- Firmware Version: VAM51JJ0 User Capacity: 41,110,142,976 bytes [41,1 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 0 Local Time is: Sun May 8 23:25:10 2016 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 192 (intermediate), recommended: 192 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1261) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 21) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 3 Spin_Up_Time POS--K 233 233 063 - 7023 4 Start_Stop_Count -O--CK 253 253 000 - 1235 5 Reallocated_Sector_Ct PO--CK 253 253 063 - 0 6 Read_Channel_Margin P----- 253 253 100 - 0 7 Seek_Error_Rate -O-R-- 253 252 000 - 0 8 Seek_Time_Performance POS--K 248 239 187 - 55583 9 Power_On_Minutes -O--CK 232 232 000 - 867h+53m 10 Spin_Retry_Count PO-R-K 253 252 157 - 0 11 Calibration_Retry_Count PO-R-K 253 252 223 - 0 12 Power_Cycle_Count -O--CK 250 250 000 - 1240 192 Power-Off_Retract_Count -O--CK 252 252 000 - 1226 193 Load_Cycle_Count -O--CK 252 252 000 - 5041 194 Temperature_Celsius -O--CK 253 253 000 - 36 195 Hardware_ECC_Recovered -O-R-- 253 252 000 - 19472 196 Reallocated_Event_Count ---R-- 253 253 000 - 0 197 Current_Pending_Sector ---R-- 253 253 000 - 0 198 Offline_Uncorrectable ---R-- 253 253 000 - 0 199 UDMA_CRC_Error_Count ---R-- 199 199 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 253 253 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 1 202 Data_Address_Mark_Errs -O-R-- 253 253 000 - 0 203 Run_Out_Cancel PO-R-- 253 253 180 - 0 204 Soft_ECC_Correction -O-R-- 253 253 000 - 0 205 Thermal_Asperity_Rate -O-R-- 253 253 000 - 0 207 Spin_High_Current -O-R-K 253 252 000 - 0 208 Spin_Buzz -O-R-K 253 252 000 - 0 209 Offline_Seek_Performnce --S--K 163 161 000 - 0 99 Unknown_Attribute --S--- 253 253 000 - 0 100 Unknown_Attribute --S--- 253 253 000 - 0 101 Unknown_Attribute --S--- 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning Read SMART Log Directory failed: scsi error badly formed scsi parameters ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read GP Log Directory failed SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 1 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 50 40 97 03 10 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef fe 00 00 00 00 10 00 00:02:28.368 SET FEATURES [Reserved for CFA] ec 00 01 01 00 00 10 00 00:02:28.320 IDENTIFY DEVICE c3 e4 00 00 00 00 10 00 00:02:28.304 [VENDOR SPECIFIC] ef 42 c0 00 00 00 10 00 00:02:28.288 SET FEATURES [Enable AAM] [OBS-ACS-2] c3 3d 00 00 00 00 10 00 00:02:28.240 [VENDOR SPECIFIC] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported