/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.15.0-desktop-122.124.1rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven OEM SSDs Device Model: SPCC Solid State Disk Serial Number: -- Firmware Version: SBFM61.3 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Dec 1 21:35:42 2020 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 9 Power_On_Hours -O--C- 100 100 000 - 1332 12 Power_Cycle_Count -O--C- 100 100 000 - 298 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 170 Bad_Blk_Ct_Erl/Lat PO---- 100 100 000 - 0/69 173 MaxAvgErase_Ct -O--C- 100 100 000 - 27 (Average 26) 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 22 194 Temperature_Celsius PO---K 067 067 000 - 33 (Min/Max 33/33) 218 CRC_Error_Count PO-R-- 100 100 050 - 0 231 SSD_Life_Left PO--C- 100 100 000 - 99 241 Lifetime_Writes_GiB -O--C- 100 100 000 - 2536 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 298 --- Lifetime Power-On Resets 0x01 0x010 4 1332 --- Power-on Hours 0x01 0x018 6 5318979337 --- Logical Sectors Written 0x01 0x028 6 5129797821 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 898 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 8 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-4.15.0-desktop-122.124.1rosa-x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000.C Device Model: Hitachi HDS721010CLA332 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: JP4OA3EA User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Dec 1 21:35:42 2020 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9988) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 167) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 135 135 054 - 99 3 Spin_Up_Time POS--- 120 120 024 - 315 (Average 316) 4 Start_Stop_Count -O--C- 098 098 000 - 10371 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 14 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 140 140 020 - 30 9 Power_On_Hours -O--C- 096 096 000 - 34476 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 10079 192 Power-Off_Retract_Count -O--CK 092 092 000 - 10371 193 Load_Cycle_Count -O--C- 092 092 000 - 10371 194 Temperature_Celsius -O---- 181 181 000 - 33 (Min/Max 8/42) 196 Reallocated_Event_Count -O--CK 100 100 000 - 14 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 25687 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 25687 [2] occurred at disk power-on lifetime: 26575 hours (1107 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 93 fa 56 00 00 Error: UNC 2 sectors at LBA = 0x0093fa56 = 9697878 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 93 fa 50 e0 00 47d+13:43:10.740 READ DMA EXT 35 00 00 00 08 00 00 00 63 50 68 e0 00 47d+13:43:10.738 WRITE DMA EXT 35 00 00 00 08 00 00 00 63 05 a0 e0 00 47d+13:43:10.735 WRITE DMA EXT 25 00 00 00 40 00 00 00 50 eb e0 e0 00 47d+13:43:10.734 READ DMA EXT 25 00 00 00 40 00 00 00 31 25 6a e0 00 47d+13:43:10.673 READ DMA EXT Error 25686 [1] occurred at disk power-on lifetime: 26575 hours (1107 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 93 fa 56 00 00 Error: UNC 2 sectors at LBA = 0x0093fa56 = 9697878 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 93 fa 50 e0 00 47d+13:42:51.932 READ DMA EXT 25 00 00 00 40 00 00 00 52 b6 40 e0 00 47d+13:42:51.870 READ DMA EXT 25 00 00 00 40 00 00 00 50 eb a0 e0 00 47d+13:42:51.841 READ DMA EXT 25 00 00 00 40 00 00 00 50 d9 e8 e0 00 47d+13:42:51.840 READ DMA EXT 25 00 00 00 40 00 00 00 4e f8 30 e0 00 47d+13:42:51.783 READ DMA EXT Error 25685 [0] occurred at disk power-on lifetime: 26575 hours (1107 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 93 fa 56 00 00 Error: UNC 2 sectors at LBA = 0x0093fa56 = 9697878 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 93 fa 50 e0 00 47d+13:42:32.434 READ DMA EXT 25 00 00 00 08 00 00 00 66 b6 58 e0 00 47d+13:42:32.406 READ DMA EXT 25 00 00 00 08 00 00 00 64 2e 88 e0 00 47d+13:42:32.370 READ DMA EXT 35 00 00 00 08 00 00 00 63 05 a0 e0 00 47d+13:42:32.366 WRITE DMA EXT 35 00 00 00 30 00 00 00 5f 81 c8 e0 00 47d+13:42:32.364 WRITE DMA EXT Error 25684 [3] occurred at disk power-on lifetime: 26575 hours (1107 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 00 93 fa 56 00 00 Error: UNC 2 sectors at LBA = 0x0093fa56 = 9697878 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 93 fa 50 e0 00 47d+13:42:13.793 READ DMA EXT 35 00 00 00 20 00 00 00 8b 4f d0 e0 00 47d+13:42:13.783 WRITE DMA EXT 35 00 00 00 40 00 00 00 76 ba 38 e0 00 47d+13:42:13.769 WRITE DMA EXT 35 00 00 00 08 00 00 00 63 49 a0 e0 00 47d+13:42:13.766 WRITE DMA EXT 25 00 00 00 08 00 00 00 63 33 10 e0 00 47d+13:42:13.714 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 24/35 Celsius Lifetime Min/Max Temperature: 8/42 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (121) Index Estimated Time Temperature Celsius 122 2020-12-01 19:28 28 ********* ... ..( 23 skipped). .. ********* 18 2020-12-01 19:52 28 ********* 19 2020-12-01 19:53 29 ********** ... ..( 7 skipped). .. ********** 27 2020-12-01 20:01 29 ********** 28 2020-12-01 20:02 28 ********* ... ..( 7 skipped). .. ********* 36 2020-12-01 20:10 28 ********* 37 2020-12-01 20:11 29 ********** 38 2020-12-01 20:12 29 ********** 39 2020-12-01 20:13 29 ********** 40 2020-12-01 20:14 30 *********** 41 2020-12-01 20:15 30 *********** 42 2020-12-01 20:16 30 *********** 43 2020-12-01 20:17 31 ************ ... ..( 3 skipped). .. ************ 47 2020-12-01 20:21 31 ************ 48 2020-12-01 20:22 32 ************* ... ..( 2 skipped). .. ************* 51 2020-12-01 20:25 32 ************* 52 2020-12-01 20:26 33 ************** ... ..( 14 skipped). .. ************** 67 2020-12-01 20:41 33 ************** 68 2020-12-01 20:42 34 *************** ... ..( 2 skipped). .. *************** 71 2020-12-01 20:45 34 *************** 72 2020-12-01 20:46 35 **************** 73 2020-12-01 20:47 35 **************** 74 2020-12-01 20:48 35 **************** 75 2020-12-01 20:49 34 *************** ... ..( 4 skipped). .. *************** 80 2020-12-01 20:54 34 *************** 81 2020-12-01 20:55 33 ************** ... ..( 7 skipped). .. ************** 89 2020-12-01 21:03 33 ************** 90 2020-12-01 21:04 34 *************** 91 2020-12-01 21:05 33 ************** ... ..( 29 skipped). .. ************** 121 2020-12-01 21:35 33 ************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 10079 --- Lifetime Power-On Resets 0x01 0x010 4 34476 --- Power-on Hours 0x01 0x018 6 118489600111 --- Logical Sectors Written 0x01 0x020 6 1834359175 --- Number of Write Commands 0x01 0x028 6 402150783597 --- Logical Sectors Read 0x01 0x030 6 3189021451 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 34241 --- Spindle Motor Power-on Hours 0x03 0x010 4 34241 --- Head Flying Hours 0x03 0x018 4 10371 --- Head Load Events 0x03 0x020 4 14 --- Number of Reallocated Logical Sectors 0x03 0x028 4 30138 --- Read Recovery Attempts 0x03 0x030 4 3 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 25683 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 15268 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x010 1 29 N-- Average Short Term Temperature 0x05 0x018 1 28 N-- Average Long Term Temperature 0x05 0x020 1 42 --- Highest Temperature 0x05 0x028 1 8 --- Lowest Temperature 0x05 0x030 1 36 N-- Highest Average Short Term Temperature 0x05 0x038 1 0 N-- Lowest Average Short Term Temperature 0x05 0x040 1 35 N-- Highest Average Long Term Temperature 0x05 0x048 1 0 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 15857 --- Number of Hardware Resets 0x06 0x010 4 5776 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0009 2 7 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS