/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-08WN4A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.01A02 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Apr 16 19:18:11 2020 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 113) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 178 171 021 - 2100 4 Start_Stop_Count -O--CK 100 100 000 - 548 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 099 099 000 - 766 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 541 192 Power-Off_Retract_Count -O--CK 200 200 000 - 207 193 Load_Cycle_Count -O--CK 200 200 000 - 357 194 Temperature_Celsius -O---K 111 107 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 48 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 9 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9 [8] occurred at disk power-on lifetime: 91 hours (3 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c ca c6 a7 40 00 Error: WP at LBA = 0x3ccac6a7 = 1019922087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 a8 00 40 00 00 09 74 77 d8 40 08 00:13:55.705 WRITE FPDMA QUEUED 61 00 a8 00 38 00 00 09 74 77 30 40 08 00:13:55.704 WRITE FPDMA QUEUED 61 00 a8 00 30 00 00 09 74 76 88 40 08 00:13:55.703 WRITE FPDMA QUEUED 61 00 a8 00 28 00 00 09 74 75 e0 40 08 00:13:55.703 WRITE FPDMA QUEUED 61 00 a8 00 20 00 00 09 74 75 38 40 08 00:13:55.702 WRITE FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 91 hours (3 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c ca c6 a6 40 00 Error: WP at LBA = 0x3ccac6a6 = 1019922086 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 a8 00 00 00 00 09 74 60 e0 40 08 00:13:55.503 WRITE FPDMA QUEUED 61 00 a8 00 e8 00 00 09 74 60 38 40 08 00:13:55.503 WRITE FPDMA QUEUED 61 00 a8 00 e0 00 00 09 74 5f 90 40 08 00:13:55.502 WRITE FPDMA QUEUED 61 00 a8 00 d0 00 00 09 74 5e e8 40 08 00:13:55.502 WRITE FPDMA QUEUED 61 00 a8 00 c8 00 00 09 74 5e 40 40 08 00:13:55.496 WRITE FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 91 hours (3 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c ca c6 a5 40 00 Error: WP at LBA = 0x3ccac6a5 = 1019922085 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 a8 00 d0 00 00 09 74 4b e0 40 08 00:13:55.302 WRITE FPDMA QUEUED 61 00 a8 00 c8 00 00 09 74 4b 38 40 08 00:13:55.295 WRITE FPDMA QUEUED 61 00 a8 00 b8 00 00 09 74 4a 90 40 08 00:13:55.295 WRITE FPDMA QUEUED 61 00 a8 00 b0 00 00 09 74 3b 78 40 08 00:13:55.295 WRITE FPDMA QUEUED 61 00 a8 00 a8 00 00 09 74 3c 20 40 08 00:13:55.295 WRITE FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 91 hours (3 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c ca c6 a4 40 00 Error: WP at LBA = 0x3ccac6a4 = 1019922084 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 a8 00 e0 00 00 09 74 3a 28 40 08 00:13:55.109 WRITE FPDMA QUEUED 61 00 a8 00 c0 00 00 09 74 39 80 40 08 00:13:55.109 WRITE FPDMA QUEUED 61 00 a8 00 b8 00 00 09 74 2a 68 40 08 00:13:55.104 WRITE FPDMA QUEUED 61 00 a8 00 b0 00 00 09 74 29 c0 40 08 00:13:55.103 WRITE FPDMA QUEUED 61 00 a8 00 a8 00 00 09 74 2b 10 40 08 00:13:55.103 WRITE FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 91 hours (3 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c ca c6 a3 40 00 Error: WP at LBA = 0x3ccac6a3 = 1019922083 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 a8 00 08 00 00 09 74 29 c0 40 08 00:13:54.918 WRITE FPDMA QUEUED 61 00 a8 00 00 00 00 09 74 2a 68 40 08 00:13:54.918 WRITE FPDMA QUEUED 61 00 a8 00 d0 00 00 09 74 29 18 40 08 00:13:54.918 WRITE FPDMA QUEUED 61 00 a8 00 c8 00 00 09 74 19 58 40 08 00:13:54.912 WRITE FPDMA QUEUED 60 00 01 00 c0 00 00 3c ca c6 a7 40 08 00:13:54.912 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 91 hours (3 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c ca c6 a2 40 00 Error: UNC at LBA = 0x3ccac6a2 = 1019922082 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 f0 00 00 3c ca c6 a6 40 08 00:13:54.720 READ FPDMA QUEUED 60 00 01 00 e8 00 00 3c ca c6 a5 40 08 00:13:54.719 READ FPDMA QUEUED 60 00 01 00 e0 00 00 3c ca c6 a4 40 08 00:13:54.719 READ FPDMA QUEUED 60 00 01 00 d8 00 00 3c ca c6 a3 40 08 00:13:54.719 READ FPDMA QUEUED 60 00 01 00 d0 00 00 3c ca c6 a2 40 08 00:13:54.719 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 91 hours (3 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c ca c6 a1 40 00 Error: WP at LBA = 0x3ccac6a1 = 1019922081 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 a8 00 48 00 00 09 74 09 98 40 08 00:13:54.527 WRITE FPDMA QUEUED 61 00 a8 00 40 00 00 09 74 08 f0 40 08 00:13:54.527 WRITE FPDMA QUEUED 61 00 a8 00 38 00 00 09 74 08 48 40 08 00:13:54.527 WRITE FPDMA QUEUED 60 00 01 00 28 00 00 3c ca c6 a1 40 08 00:13:54.527 READ FPDMA QUEUED 60 00 01 00 20 00 00 3c ca c6 a2 40 08 00:13:54.527 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 91 hours (3 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3c ca c6 a0 40 00 Error: UNC at LBA = 0x3ccac6a0 = 1019922080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 a0 00 00 3c ca c6 a0 40 08 00:13:54.344 READ FPDMA QUEUED 60 00 01 00 98 00 00 3c ca c6 9f 40 08 00:13:54.344 READ FPDMA QUEUED 60 00 01 00 90 00 00 3c ca c6 9e 40 08 00:13:54.344 READ FPDMA QUEUED 60 00 01 00 88 00 00 3c ca c6 9d 40 08 00:13:54.344 READ FPDMA QUEUED 60 00 01 00 80 00 00 3c ca c6 9c 40 08 00:13:54.344 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 523 - # 2 Short offline Interrupted (host reset) 10% 359 - # 3 Short offline Interrupted (host reset) 90% 236 - # 4 Short offline Completed without error 00% 3 - # 5 Short offline Completed without error 00% 2 - # 6 Short offline Completed without error 00% 2 - # 7 Short offline Completed without error 00% 0 - # 8 Short offline Completed without error 00% 0 - # 9 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 25/32 Celsius Lifetime Min/Max Temperature: 22/36 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (166) Index Estimated Time Temperature Celsius 167 2020-04-16 11:21 26 ******* 168 2020-04-16 11:22 27 ******** 169 2020-04-16 11:23 27 ******** 170 2020-04-16 11:24 28 ********* ... ..( 2 skipped). .. ********* 173 2020-04-16 11:27 28 ********* 174 2020-04-16 11:28 29 ********** ... ..( 5 skipped). .. ********** 180 2020-04-16 11:34 29 ********** 181 2020-04-16 11:35 30 *********** ... ..( 24 skipped). .. *********** 206 2020-04-16 12:00 30 *********** 207 2020-04-16 12:01 31 ************ ... ..( 41 skipped). .. ************ 249 2020-04-16 12:43 31 ************ 250 2020-04-16 12:44 ? - 251 2020-04-16 12:45 25 ****** 252 2020-04-16 12:46 24 ***** 253 2020-04-16 12:47 25 ****** 254 2020-04-16 12:48 25 ****** 255 2020-04-16 12:49 26 ******* 256 2020-04-16 12:50 26 ******* 257 2020-04-16 12:51 27 ******** 258 2020-04-16 12:52 27 ******** 259 2020-04-16 12:53 27 ******** 260 2020-04-16 12:54 28 ********* 261 2020-04-16 12:55 28 ********* 262 2020-04-16 12:56 28 ********* 263 2020-04-16 12:57 29 ********** ... ..( 4 skipped). .. ********** 268 2020-04-16 13:02 29 ********** 269 2020-04-16 13:03 30 *********** ... ..( 8 skipped). .. *********** 278 2020-04-16 13:12 30 *********** 279 2020-04-16 13:13 31 ************ ... ..( 41 skipped). .. ************ 321 2020-04-16 13:55 31 ************ 322 2020-04-16 13:56 ? - 323 2020-04-16 13:57 25 ****** 324 2020-04-16 13:58 25 ****** 325 2020-04-16 13:59 25 ****** 326 2020-04-16 14:00 26 ******* 327 2020-04-16 14:01 26 ******* 328 2020-04-16 14:02 26 ******* 329 2020-04-16 14:03 27 ******** 330 2020-04-16 14:04 27 ******** 331 2020-04-16 14:05 28 ********* 332 2020-04-16 14:06 28 ********* 333 2020-04-16 14:07 28 ********* 334 2020-04-16 14:08 29 ********** ... ..( 6 skipped). .. ********** 341 2020-04-16 14:15 29 ********** 342 2020-04-16 14:16 30 *********** ... ..( 9 skipped). .. *********** 352 2020-04-16 14:26 30 *********** 353 2020-04-16 14:27 31 ************ ... ..( 80 skipped). .. ************ 434 2020-04-16 15:48 31 ************ 435 2020-04-16 15:49 ? - 436 2020-04-16 15:50 25 ****** ... ..( 2 skipped). .. ****** 439 2020-04-16 15:53 25 ****** 440 2020-04-16 15:54 26 ******* 441 2020-04-16 15:55 26 ******* 442 2020-04-16 15:56 27 ******** 443 2020-04-16 15:57 27 ******** 444 2020-04-16 15:58 28 ********* ... ..( 2 skipped). .. ********* 447 2020-04-16 16:01 28 ********* 448 2020-04-16 16:02 29 ********** 449 2020-04-16 16:03 ? - 450 2020-04-16 16:04 30 *********** 451 2020-04-16 16:05 ? - 452 2020-04-16 16:06 30 *********** ... ..( 10 skipped). .. *********** 463 2020-04-16 16:17 30 *********** 464 2020-04-16 16:18 31 ************ ... ..( 97 skipped). .. ************ 84 2020-04-16 17:56 31 ************ 85 2020-04-16 17:57 ? - 86 2020-04-16 17:58 25 ****** 87 2020-04-16 17:59 ? - 88 2020-04-16 18:00 25 ****** 89 2020-04-16 18:01 ? - 90 2020-04-16 18:02 25 ****** 91 2020-04-16 18:03 25 ****** 92 2020-04-16 18:04 25 ****** 93 2020-04-16 18:05 26 ******* 94 2020-04-16 18:06 26 ******* 95 2020-04-16 18:07 27 ******** 96 2020-04-16 18:08 27 ******** 97 2020-04-16 18:09 28 ********* ... ..( 3 skipped). .. ********* 101 2020-04-16 18:13 28 ********* 102 2020-04-16 18:14 29 ********** ... ..( 3 skipped). .. ********** 106 2020-04-16 18:18 29 ********** 107 2020-04-16 18:19 30 *********** ... ..( 5 skipped). .. *********** 113 2020-04-16 18:25 30 *********** 114 2020-04-16 18:26 31 ************ ... ..( 18 skipped). .. ************ 133 2020-04-16 18:45 31 ************ 134 2020-04-16 18:46 32 ************* ... ..( 31 skipped). .. ************* 166 2020-04-16 19:18 32 ************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 4686 Vendor specific