/dev/sdb === START OF INFORMATION SECTION === Device Model: SPCC Solid State Disk Serial Number: -- LU WWN Device Id: 5 02b2a2 ... Add. Product Id: mavlsata Firmware Version: V3.10 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Apr 29 16:21:34 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x35) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x00) Error logging NOT supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 1) minutes. Conveyance self-test routine recommended polling time: ( 1) minutes. SMART Attributes Data Structure revision number: 5 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours PO--CK 100 100 010 - 7046 12 Power_Cycle_Count PO--CK 100 100 010 - 953 161 Unknown_Attribute PO--CK 100 100 010 - 0 164 Unknown_Attribute PO--CK 100 100 010 - 26911 165 Unknown_Attribute PO--CK 100 100 010 - 60 166 Unknown_Attribute PO--CK 100 100 010 - 58 167 Unknown_Attribute PO--CK 100 100 010 - 58 169 Unknown_Attribute PO--CK 100 100 010 - 0 176 Erase_Fail_Count_Chip PO--CK 100 100 010 - 0 177 Wear_Leveling_Count PO--CK 100 100 010 - 0 178 Used_Rsvd_Blk_Cnt_Chip PO--CK 100 100 010 - 0 192 Power-Off_Retract_Count PO--CK 100 100 010 - 5 194 Temperature_Celsius PO--CK 100 100 010 - 44 195 Hardware_ECC_Recovered PO--CK 100 100 010 - 0 199 UDMA_CRC_Error_Count PO--CK 100 100 010 - 0 241 Total_LBAs_Written PO--CK 100 100 010 - 9046 242 Total_LBAs_Read PO--CK 100 100 010 - 5654 243 Unknown_Attribute PO--CK 100 100 010 - 0 244 Unknown_Attribute PO--CK 100 100 010 - 0 245 Unknown_Attribute PO--CK 100 100 010 - 0 246 Unknown_Attribute PO--CK 100 100 010 - 0 250 Read_Error_Retry_Rate PO--CK 100 100 010 - 0 251 Unknown_Attribute PO--CK 100 100 010 - 0 252 Unknown_Attribute PO--CK 100 100 010 - 0 253 Unknown_Attribute PO--CK 100 100 010 - 0 254 Unknown_SSD_Attribute PO--CK 100 100 010 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x10 GPL,SL R/O 1 NCQ Command Error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test Log not supported Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported /dev/sdc === START OF INFORMATION SECTION === Device Model: CT120BX500SSD1 Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: M6CR013 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Apr 29 16:21:34 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 050 - 960 12 Power_Cycle_Count -O--CK 100 100 050 - 116 171 Unknown_Attribute -O--CK 100 100 050 - 0 172 Unknown_Attribute -O--CK 100 100 050 - 0 173 Unknown_Attribute -O--CK 100 100 050 - 46 174 Unknown_Attribute -O--CK 100 100 050 - 46 180 Unused_Rsvd_Blk_Cnt_Tot -O--CK 100 100 050 - 100 183 Runtime_Bad_Block -O--CK 100 100 050 - 0 184 End-to-End_Error -O--CK 100 100 050 - 0 187 Reported_Uncorrect -O--CK 100 100 050 - 0 194 Temperature_Celsius -O---K 062 043 050 Past 38 (Min/Max 20/57) 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable ----CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 0 202 Unknown_SSD_Attribute ----CK 097 097 001 - 97 206 Unknown_SSD_Attribute -OSR-K 100 100 050 - 0 210 Unknown_Attribute -O--CK 100 100 050 - 0 246 Unknown_Attribute -O--CK 100 100 050 - 2333720674 247 Unknown_Attribute -O--CK 100 100 050 - 72928771 248 Unknown_Attribute -O--CK 100 100 050 - 69341184 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 32 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 116 --- Lifetime Power-On Resets 0x01 0x010 4 960 --- Power-on Hours 0x01 0x018 6 2333720674 --- Logical Sectors Written 0x01 0x020 6 28648362 --- Number of Write Commands 0x01 0x028 6 876556288 --- Logical Sectors Read 0x01 0x030 6 12891522 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 3 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 31 Device-to-host register FISes sent due to a COMRESET /dev/sdd === START OF INFORMATION SECTION === Model Family: Western Digital Black Mobile Device Model: WDC WD3200BEKX-00B7WT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Apr 29 16:21:34 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6060) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 63) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 160 137 021 - 958 4 Start_Stop_Count -O--CK 093 093 000 - 7049 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 080 080 000 - 15030 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2745 192 Power-Off_Retract_Count -O--CK 199 199 000 - 780 193 Load_Cycle_Count -O--CK 166 166 000 - 103978 194 Temperature_Celsius -O---K 106 085 000 - 37 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 187 000 - 7331 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 9 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9 [8] occurred at disk power-on lifetime: 6111 hours (254 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 02:49:25.718 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 02:49:25.717 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:49:25.717 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 5e 08 00 00 00 00 e0 00 02:49:25.716 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 02:49:25.714 IDENTIFY DEVICE Error 8 [7] occurred at disk power-on lifetime: 6111 hours (254 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 02:49:25.717 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:49:25.717 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 5e 08 00 00 00 00 e0 00 02:49:25.716 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 02:49:25.714 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 02:49:25.712 IDENTIFY DEVICE Error 7 [6] occurred at disk power-on lifetime: 6111 hours (254 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 02:49:25.329 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 02:49:25.328 SMART WRITE LOG 35 00 00 00 08 00 00 00 17 10 40 e0 00 02:49:23.264 WRITE DMA EXT 35 00 00 00 08 00 00 00 5e 07 f0 e0 00 02:49:18.210 WRITE DMA EXT ea 00 00 00 00 5e 08 07 00 00 00 e0 00 02:49:18.179 FLUSH CACHE EXT Error 6 [5] occurred at disk power-on lifetime: 6111 hours (254 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 02:49:25.328 SMART WRITE LOG 35 00 00 00 08 00 00 00 17 10 40 e0 00 02:49:23.264 WRITE DMA EXT 35 00 00 00 08 00 00 00 5e 07 f0 e0 00 02:49:18.210 WRITE DMA EXT ea 00 00 00 00 5e 08 07 00 00 00 e0 00 02:49:18.179 FLUSH CACHE EXT 35 00 00 00 08 00 00 00 5e 08 00 e0 00 02:49:18.179 WRITE DMA EXT Error 5 [4] occurred at disk power-on lifetime: 6111 hours (254 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 02:49:00.766 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 02:49:00.766 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:49:00.764 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 00 00 00 00 00 00 e0 00 02:49:00.763 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 02:49:00.761 IDENTIFY DEVICE Error 4 [3] occurred at disk power-on lifetime: 6111 hours (254 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 e0 00 02:49:00.766 SMART WRITE LOG 27 00 00 00 00 00 00 00 00 00 00 e0 00 02:49:00.764 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 01 00 00 00 00 00 00 e0 00 02:49:00.763 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 02:49:00.761 IDENTIFY DEVICE ec 00 00 00 01 00 00 00 00 00 00 e0 00 02:49:00.760 IDENTIFY DEVICE Error 3 [2] occurred at disk power-on lifetime: 6111 hours (254 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 02:49:00.342 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 02:49:00.341 SMART WRITE LOG 35 00 00 00 08 00 00 00 5e 07 f0 e0 00 02:48:57.997 WRITE DMA EXT ea 00 00 00 00 5e 08 07 00 00 00 e0 00 02:48:57.963 FLUSH CACHE EXT 35 00 00 00 08 00 00 00 5e 08 00 e0 00 02:48:57.963 WRITE DMA EXT Error 2 [1] occurred at disk power-on lifetime: 6111 hours (254 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 02:49:00.341 SMART WRITE LOG 35 00 00 00 08 00 00 00 5e 07 f0 e0 00 02:48:57.997 WRITE DMA EXT ea 00 00 00 00 5e 08 07 00 00 00 e0 00 02:48:57.963 FLUSH CACHE EXT 35 00 00 00 08 00 00 00 5e 08 00 e0 00 02:48:57.963 WRITE DMA EXT 35 00 00 00 08 00 00 00 60 c3 48 e0 00 02:48:52.923 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 7612 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Max Temperature: 42 Celsius Lifetime Max Temperature: 58 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (88) Index Estimated Time Temperature Celsius 89 2019-04-29 14:14 39 ******************** ... ..( 31 skipped). .. ******************** 121 2019-04-29 14:46 39 ******************** 122 2019-04-29 14:47 38 ******************* ... ..( 31 skipped). .. ******************* 26 2019-04-29 15:19 38 ******************* 27 2019-04-29 15:20 39 ******************** 28 2019-04-29 15:21 38 ******************* ... ..( 12 skipped). .. ******************* 41 2019-04-29 15:34 38 ******************* 42 2019-04-29 15:35 37 ****************** 43 2019-04-29 15:36 38 ******************* 44 2019-04-29 15:37 38 ******************* 45 2019-04-29 15:38 38 ******************* 46 2019-04-29 15:39 37 ****************** 47 2019-04-29 15:40 37 ****************** 48 2019-04-29 15:41 38 ******************* ... ..( 3 skipped). .. ******************* 52 2019-04-29 15:45 38 ******************* 53 2019-04-29 15:46 37 ****************** 54 2019-04-29 15:47 37 ****************** 55 2019-04-29 15:48 37 ****************** 56 2019-04-29 15:49 38 ******************* 57 2019-04-29 15:50 37 ****************** ... ..( 7 skipped). .. ****************** 65 2019-04-29 15:58 37 ****************** 66 2019-04-29 15:59 36 ***************** 67 2019-04-29 16:00 37 ****************** ... ..( 5 skipped). .. ****************** 73 2019-04-29 16:06 37 ****************** 74 2019-04-29 16:07 36 ***************** 75 2019-04-29 16:08 37 ****************** 76 2019-04-29 16:09 37 ****************** 77 2019-04-29 16:10 36 ***************** 78 2019-04-29 16:11 37 ****************** ... ..( 9 skipped). .. ****************** 88 2019-04-29 16:21 37 ****************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 31 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 23 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 65510 Vendor specific