/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD3200AAJS-40RYA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 12.01B03 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sat Nov 2 19:56:46 2019 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 106) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 0 3 Spin_Up_Time PO---- 163 158 021 - 4833 4 Start_Stop_Count -O--CK 091 091 000 - 9918 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 057 057 000 - 32114 10 Spin_Retry_Count -O--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 091 091 000 - 9043 192 Power-Off_Retract_Count -O--CK 198 198 000 - 1538 193 Load_Cycle_Count -O--CK 197 197 000 - 10086 194 Temperature_Celsius -O---K 095 087 000 - 52 195 Hardware_ECC_Recovered -OSR-- 001 001 000 - 104217906 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 12 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 5 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 a3 25 00 9a 00 00 00 00 00 00 00 08 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 a0 00 db 08 91 25 00 00 00 00:00:40.960 NOP [Abort queued commands] 08 40 25 00 80 00 00 00 a0 00 00 00 08 00:00:35.092 DEVICE RESET 00 01 00 00 10 00 40 00 80 2f 00 00 00 00:00:40.960 NOP [Abort queued commands] Error 4 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 db 25 00 91 00 00 00 00 00 00 00 08 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 a0 00 14 08 89 25 00 00 00 00:00:40.960 NOP [Abort queued commands] 08 40 2f 00 80 00 00 00 a0 00 00 00 00 00:00:32.832 DEVICE RESET 00 40 00 00 a0 00 1b 08 77 60 00 00 00 00:00:04.097 NOP [Abort queued commands] Error 3 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 14 25 00 89 00 00 00 00 00 00 00 08 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 a0 00 40 08 80 25 00 00 00 00:00:40.960 NOP [Abort queued commands] 00 1b 60 00 77 00 01 00 10 00 00 00 08 00:00:32.832 NOP [Reserved subcommand] [OBS-ACS-2] 00 38 10 00 e8 00 1b 0b 77 61 00 00 00 00:00:41.024 NOP [Reserved subcommand] [OBS-ACS-2] Error 2 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 40 25 00 80 00 00 00 00 00 00 00 08 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 01 00 00 10 00 40 00 80 2f 00 00 00 00:00:40.960 NOP [Abort queued commands] 08 1b 61 00 77 00 40 00 a0 00 00 00 0b 00:00:30.491 DEVICE RESET 00 30 40 00 38 00 18 08 77 60 00 00 00 00:00:59.448 NOP [Reserved subcommand] [OBS-ACS-2] Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 1b 60 00 77 00 00 00 00 00 00 00 08 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 38 10 00 e8 00 1b 0b 77 61 00 00 00 00:00:41.024 NOP [Reserved subcommand] [OBS-ACS-2] 08 17 61 00 77 00 30 00 38 40 00 00 0b 00:00:30.488 DEVICE RESET 00 20 c0 00 d0 00 12 08 77 60 00 00 00 00:00:57.384 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 28108 - # 2 Short offline Aborted by host 90% 23 - # 3 Short offline Aborted by host 90% 23 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 52 Celsius Power Cycle Min/Max Temperature: 52/52 Celsius Lifetime Min/Max Temperature: 51/60 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (16) Index Estimated Time Temperature Celsius 17 2019-11-02 17:49 51 ******************************** ... ..( 11 skipped). .. ******************************** 29 2019-11-02 18:01 51 ******************************** 30 2019-11-02 18:02 50 ******************************* ... ..( 36 skipped). .. ******************************* 67 2019-11-02 18:39 50 ******************************* 68 2019-11-02 18:40 51 ******************************** ... ..( 25 skipped). .. ******************************** 94 2019-11-02 19:06 51 ******************************** 95 2019-11-02 19:07 52 ********************************* ... ..( 26 skipped). .. ********************************* 122 2019-11-02 19:34 52 ********************************* 123 2019-11-02 19:35 ? - 124 2019-11-02 19:36 52 ********************************* ... ..( 18 skipped). .. ********************************* 15 2019-11-02 19:55 52 ********************************* 16 2019-11-02 19:56 51 ******************************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x8000 4 1201 Vendor specific