/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue (SATA) Device Model: WDC WD5000AAKS-65A7B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.03B01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sun Apr 2 07:36:24 2023 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11160) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 131) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 0 3 Spin_Up_Time PO---- 158 153 021 - 5100 4 Start_Stop_Count -O--CK 100 100 000 - 6 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 067 067 000 - 24489 10 Spin_Retry_Count -O--C- 100 253 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5350 192 Power-Off_Retract_Count -O--CK 200 200 000 - 583 193 Load_Cycle_Count -O--CK 199 199 000 - 5350 194 Temperature_Celsius -O---K 105 082 000 - 42 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 3 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 e5 60 4d c0 00 00 00 00 00 00 00 11 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 38 10 00 20 4d e5 0c c0 61 00 00 08 00:00:59.456 DEVICE RESET 11 e5 60 4d c0 00 30 08 f0 08 00 00 11 01:24:55.653 RECALIBRATE [RET-4] 08 20 08 00 e8 4d e4 11 c0 60 00 00 08 00:01:03.528 DEVICE RESET Error 2 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 fe 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 a5 60 4d a7 00 00 00 00 00 00 00 11 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 10 f8 00 08 4d a5 11 a7 60 00 00 08 00:00:02.072 DEVICE RESET 13 a5 60 4d a7 00 08 08 50 08 00 00 12 01:24:49.189 RECALIBRATE [RET-4] 08 f0 00 00 48 4d a5 12 a7 60 00 00 08 00:00:20.480 DEVICE RESET Error 1 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 fe 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 fd 60 1b 5b 00 00 00 00 00 01 00 11 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 68 08 00 00 1b fd 11 5b 60 00 01 08 00:00:59.504 DEVICE RESET 11 fd 60 1b 5b 00 60 08 f8 08 01 00 11 05:09:30.237 RECALIBRATE [RET-4] 08 50 08 00 e0 1b fd 11 5b 60 00 01 08 00:01:01.528 DEVICE RESET SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 21/42 Celsius Lifetime Min/Max Temperature: 21/65 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/85 Celsius Temperature History Size (Index): 128 (3) Index Estimated Time Temperature Celsius 4 2023-04-02 05:29 46 *************************** ... ..( 61 skipped). .. *************************** 66 2023-04-02 06:31 46 *************************** 67 2023-04-02 06:32 ? - 68 2023-04-02 06:33 21 ** 69 2023-04-02 06:34 21 ** 70 2023-04-02 06:35 22 *** 71 2023-04-02 06:36 23 **** 72 2023-04-02 06:37 24 ***** 73 2023-04-02 06:38 25 ****** 74 2023-04-02 06:39 25 ****** 75 2023-04-02 06:40 26 ******* 76 2023-04-02 06:41 26 ******* 77 2023-04-02 06:42 27 ******** 78 2023-04-02 06:43 28 ********* 79 2023-04-02 06:44 29 ********** 80 2023-04-02 06:45 29 ********** 81 2023-04-02 06:46 30 *********** 82 2023-04-02 06:47 30 *********** 83 2023-04-02 06:48 30 *********** 84 2023-04-02 06:49 31 ************ 85 2023-04-02 06:50 31 ************ 86 2023-04-02 06:51 32 ************* 87 2023-04-02 06:52 33 ************** ... ..( 2 skipped). .. ************** 90 2023-04-02 06:55 33 ************** 91 2023-04-02 06:56 34 *************** ... ..( 2 skipped). .. *************** 94 2023-04-02 06:59 34 *************** 95 2023-04-02 07:00 35 **************** 96 2023-04-02 07:01 35 **************** 97 2023-04-02 07:02 36 ***************** 98 2023-04-02 07:03 36 ***************** 99 2023-04-02 07:04 37 ****************** ... ..( 4 skipped). .. ****************** 104 2023-04-02 07:09 37 ****************** 105 2023-04-02 07:10 38 ******************* 106 2023-04-02 07:11 38 ******************* 107 2023-04-02 07:12 38 ******************* 108 2023-04-02 07:13 39 ******************** ... ..( 2 skipped). .. ******************** 111 2023-04-02 07:16 39 ******************** 112 2023-04-02 07:17 40 ********************* ... ..( 3 skipped). .. ********************* 116 2023-04-02 07:21 40 ********************* 117 2023-04-02 07:22 41 ********************** 118 2023-04-02 07:23 41 ********************** 119 2023-04-02 07:24 41 ********************** 120 2023-04-02 07:25 42 *********************** ... ..( 10 skipped). .. *********************** 3 2023-04-02 07:36 42 *********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 3880 Vendor specific