/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.14-desktop-1omv4002] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.4 Device Model: ST9250827AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 3.AAA User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s Local Time is: Mon Sep 27 13:24:21 2021 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 113) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 426) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 92) minutes. SCT capabilities: (0x0001) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0 3 Spin_Up_Time PO---- 099 099 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 905 5 Reallocated_Sector_Ct PO--CK 073 073 036 - 1088 7 Seek_Error_Rate POSR-- 059 058 030 - 536979983166 9 Power_On_Hours -O--CK 094 094 000 - 6003 10 Spin_Retry_Count PO--C- 100 100 034 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 966 187 Reported_Uncorrect -O--CK 008 008 000 - 92 189 High_Fly_Writes -O-RCK 001 001 000 - 134 190 Airflow_Temperature_Cel -O---K 058 040 045 Past 42 (Min/Max 16/60 #20) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 2 192 Power-Off_Retract_Count -O--CK 100 100 000 - 788 193 Load_Cycle_Count -O---K 073 073 000 - 55216 194 Temperature_Celsius -O-RC- 042 060 000 - 42 (0 16 0 0 0) 195 Hardware_ECC_Recovered -O--C- 092 057 000 - 77180583 197 Current_Pending_Sector ----C- 100 063 000 - 15 198 Offline_Uncorrectable -OSRCK 100 063 000 - 15 199 UDMA_CRC_Error_Count ------ 200 200 000 - 0 200 Multi_Zone_Error_Rate -O--CK 100 253 000 - 0 202 Data_Address_Mark_Errs ------ 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 SL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 SL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 SL R/O 1 NCQ Command Error log 0x11 SL R/O 1 SATA Phy Event Counters log 0x20 SL R/O 1 Streaming performance log [OBS-8] 0x21 SL R/O 1 Write stream error log 0x22 SL R/O 1 Read stream error log 0x23 SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f SL R/W 16 Host vendor specific log 0xa0 SL VS 1 Device vendor specific log 0xa1 SL VS 20 Device vendor specific log 0xa2 SL VS 101 Device vendor specific log 0xa8 SL VS 20 Device vendor specific log 0xa9 SL VS 1 Device vendor specific log 0xe0 SL R/W 1 SCT Command/Status 0xe1 SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 92 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 92 occurred at disk power-on lifetime: 5678 hours (236 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 d4 96 4f e1 Error: UNC at LBA = 0x014f96d4 = 21993172 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 c0 96 4f e1 00 00:48:37.499 READ DMA c8 00 08 c0 0e 21 ef 00 00:48:37.498 READ DMA c8 00 08 b8 0e 21 ef 00 00:48:37.541 READ DMA c8 00 00 c0 95 4f e1 00 00:48:37.529 READ DMA c8 00 08 b0 0e 21 ef 00 00:48:37.529 READ DMA Error 91 occurred at disk power-on lifetime: 5486 hours (228 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 86 44 44 e0 Error: UNC at LBA = 0x00444486 = 4473990 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 24 00 01 86 44 44 e0 00 00:07:27.648 READ SECTOR(S) EXT 42 00 ff 85 44 44 e0 00 00:07:27.590 READ VERIFY SECTOR(S) EXT 00 00 01 00 00 00 00 04 00:07:16.215 NOP [Abort queued commands] 34 00 01 84 44 44 e0 00 00:07:12.207 WRITE SECTORS(S) EXT 24 00 01 84 44 44 e0 00 00:07:11.939 READ SECTOR(S) EXT Error 90 occurred at disk power-on lifetime: 5486 hours (228 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 86 44 44 e0 Error: UNC at LBA = 0x00444486 = 4473990 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 00 ff 85 44 44 e0 00 00:07:27.648 READ VERIFY SECTOR(S) EXT 00 00 01 00 00 00 00 04 00:07:27.590 NOP [Abort queued commands] 34 00 01 84 44 44 e0 00 00:07:16.215 WRITE SECTORS(S) EXT 24 00 01 84 44 44 e0 00 00:07:12.207 READ SECTOR(S) EXT 42 00 ff 84 44 44 e0 00 00:07:11.939 READ VERIFY SECTOR(S) EXT Error 89 occurred at disk power-on lifetime: 5486 hours (228 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 84 44 44 e0 Error: UNC at LBA = 0x00444484 = 4473988 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 24 00 01 84 44 44 e0 00 00:07:27.648 READ SECTOR(S) EXT 42 00 ff 84 44 44 e0 00 00:07:27.590 READ VERIFY SECTOR(S) EXT 00 00 01 00 00 00 00 04 00:07:16.215 NOP [Abort queued commands] 34 00 01 83 44 44 e0 00 00:07:12.207 WRITE SECTORS(S) EXT 24 00 01 83 44 44 e0 00 00:07:11.939 READ SECTOR(S) EXT Error 88 occurred at disk power-on lifetime: 5486 hours (228 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 84 44 44 e0 Error: UNC at LBA = 0x00444484 = 4473988 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 00 ff 84 44 44 e0 00 00:07:27.648 READ VERIFY SECTOR(S) EXT 00 00 01 00 00 00 00 04 00:07:27.590 NOP [Abort queued commands] 34 00 01 83 44 44 e0 00 00:07:16.215 WRITE SECTORS(S) EXT 24 00 01 83 44 44 e0 00 00:07:12.207 READ SECTOR(S) EXT 42 00 ff 76 44 44 e0 00 00:07:11.939 READ VERIFY SECTOR(S) EXT SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 10% 5973 21423963 # 2 Short offline Completed: read failure 10% 5947 21423963 # 3 Short offline Completed: read failure 90% 5857 21993172 # 4 Short offline Completed: read failure 90% 5835 21993172 # 5 Extended offline Completed: read failure 90% 5776 21993172 # 6 Extended offline Completed: read failure 90% 5715 21993172 # 7 Extended offline Completed: read failure 90% 5715 21993172 # 8 Short offline Completed: read failure 90% 5715 21993172 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 521 (0x0209) Device State: Active (0) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: --/ 0 Celsius Lifetime Min/Max Temperature: --/ 0 Celsius SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 7 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x8002 2 0 Vendor specific 0x8003 2 2 Vendor specific 0x8004 2 0 Vendor specific /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.14-desktop-1omv4002] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Elements / My Passport (USB, AF) Device Model: WDC WD10JMVW-11S5XS0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Sep 27 13:24:22 2021 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (18000) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 196) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 179 171 021 - 2025 4 Start_Stop_Count -O--CK 095 095 000 - 5269 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 094 094 000 - 4957 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1040 192 Power-Off_Retract_Count -O--CK 200 200 000 - 460 193 Load_Cycle_Count -O--CK 192 192 000 - 24175 194 Temperature_Celsius -O---K 111 094 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 34/36 Celsius Lifetime Min/Max Temperature: 21/53 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (124) Index Estimated Time Temperature Celsius 125 2021-09-27 11:17 39 ******************** ... ..( 5 skipped). .. ******************** 3 2021-09-27 11:23 39 ******************** 4 2021-09-27 11:24 40 ********************* 5 2021-09-27 11:25 ? - 6 2021-09-27 11:26 21 ** 7 2021-09-27 11:27 21 ** 8 2021-09-27 11:28 21 ** 9 2021-09-27 11:29 23 **** 10 2021-09-27 11:30 23 **** 11 2021-09-27 11:31 25 ****** 12 2021-09-27 11:32 26 ******* 13 2021-09-27 11:33 26 ******* 14 2021-09-27 11:34 26 ******* 15 2021-09-27 11:35 27 ******** ... ..( 4 skipped). .. ******** 20 2021-09-27 11:40 27 ******** 21 2021-09-27 11:41 28 ********* ... ..( 5 skipped). .. ********* 27 2021-09-27 11:47 28 ********* 28 2021-09-27 11:48 29 ********** ... ..( 3 skipped). .. ********** 32 2021-09-27 11:52 29 ********** 33 2021-09-27 11:53 30 *********** ... ..( 4 skipped). .. *********** 38 2021-09-27 11:58 30 *********** 39 2021-09-27 11:59 31 ************ ... ..( 12 skipped). .. ************ 52 2021-09-27 12:12 31 ************ 53 2021-09-27 12:13 32 ************* ... ..( 3 skipped). .. ************* 57 2021-09-27 12:17 32 ************* 58 2021-09-27 12:18 31 ************ ... ..( 7 skipped). .. ************ 66 2021-09-27 12:26 31 ************ 67 2021-09-27 12:27 ? - 68 2021-09-27 12:28 31 ************ 69 2021-09-27 12:29 31 ************ 70 2021-09-27 12:30 31 ************ 71 2021-09-27 12:31 32 ************* 72 2021-09-27 12:32 32 ************* 73 2021-09-27 12:33 33 ************** ... ..( 10 skipped). .. ************** 84 2021-09-27 12:44 33 ************** 85 2021-09-27 12:45 34 *************** ... ..( 15 skipped). .. *************** 101 2021-09-27 13:01 34 *************** 102 2021-09-27 13:02 ? - 103 2021-09-27 13:03 34 *************** 104 2021-09-27 13:04 35 **************** ... ..( 10 skipped). .. **************** 115 2021-09-27 13:15 35 **************** 116 2021-09-27 13:16 ? - 117 2021-09-27 13:17 35 **************** 118 2021-09-27 13:18 35 **************** 119 2021-09-27 13:19 36 ***************** ... ..( 4 skipped). .. ***************** 124 2021-09-27 13:24 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1159 Vendor specific