/dev/sda === START OF INFORMATION SECTION === Device Model: T-60 Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: T170601b User Capacity: 60,022,480,896 bytes [60.0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: Unknown(0x0fe0) (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jan 17 23:26:40 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 33) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 66) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 9 Power_On_Hours -O--CK 100 100 000 - 296 12 Power_Cycle_Count -O--CK 100 100 000 - 30 167 Unknown_Attribute -O---K 100 100 000 - 0 168 Unknown_Attribute -O--CK 100 100 000 - 3 169 Unknown_Attribute -O--CK 100 100 010 - 0 171 Unknown_Attribute -O--CK 000 000 000 - 0 172 Unknown_Attribute -O--CK 000 000 000 - 0 173 Unknown_Attribute -O--CK 200 200 000 - 8591441933 175 Program_Fail_Count_Chip -O---K 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--CK 100 100 020 - 130 187 Reported_Uncorrect -O--CK 100 000 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 10 206 Unknown_SSD_Attribute -O--CK 200 200 000 - 2 207 Unknown_SSD_Attribute -O--CK 200 200 000 - 23 208 Unknown_SSD_Attribute -O--CK 200 200 000 - 13 231 Temperature_Celsius PO---K 100 100 005 - 0 241 Total_LBAs_Written -O--CK 100 100 000 - 732313606 242 Total_LBAs_Read -O--CK 100 100 000 - 520373424 245 Unknown_Attribute -O--CK 100 100 000 - 14416616 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) SCT Support Level: 0 Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: ?/40 Celsius Lifetime Min/Max Temperature: ?/ ? Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -127/127 Celsius Min/Max Temperature Limit: -127/127 Celsius Temperature History Size (Index): 478 (61795) Invalid Temperature History Size or Index SCT Error Recovery Control: Read: 80 (8.0 seconds) Write: 80 (8.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 3 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 11 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Green Device Model: WDC WD20EZRX-00D8PB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jan 17 23:26:40 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (26940) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 272) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 176 171 021 - 4191 4 Start_Stop_Count -O--CK 099 099 000 - 1398 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 085 085 000 - 11327 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1023 192 Power-Off_Retract_Count -O--CK 200 200 000 - 48 193 Load_Cycle_Count -O--CK 167 167 000 - 101950 194 Temperature_Celsius -O---K 117 100 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 29/30 Celsius Lifetime Min/Max Temperature: 21/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (327) Index Estimated Time Temperature Celsius 328 2018-01-17 15:29 30 *********** ... ..( 20 skipped). .. *********** 349 2018-01-17 15:50 30 *********** 350 2018-01-17 15:51 31 ************ ... ..( 52 skipped). .. ************ 403 2018-01-17 16:44 31 ************ 404 2018-01-17 16:45 32 ************* 405 2018-01-17 16:46 31 ************ ... ..( 29 skipped). .. ************ 435 2018-01-17 17:16 31 ************ 436 2018-01-17 17:17 32 ************* ... ..( 54 skipped). .. ************* 13 2018-01-17 18:12 32 ************* 14 2018-01-17 18:13 ? - 15 2018-01-17 18:14 22 *** 16 2018-01-17 18:15 22 *** 17 2018-01-17 18:16 24 ***** ... ..( 3 skipped). .. ***** 21 2018-01-17 18:20 24 ***** 22 2018-01-17 18:21 26 ******* 23 2018-01-17 18:22 25 ****** 24 2018-01-17 18:23 26 ******* 25 2018-01-17 18:24 26 ******* 26 2018-01-17 18:25 27 ******** ... ..( 5 skipped). .. ******** 32 2018-01-17 18:31 27 ******** 33 2018-01-17 18:32 28 ********* ... ..( 2 skipped). .. ********* 36 2018-01-17 18:35 28 ********* 37 2018-01-17 18:36 ? - 38 2018-01-17 18:37 29 ********** 39 2018-01-17 18:38 ? - 40 2018-01-17 18:39 30 *********** ... ..( 32 skipped). .. *********** 73 2018-01-17 19:12 30 *********** 74 2018-01-17 19:13 29 ********** ... ..( 20 skipped). .. ********** 95 2018-01-17 19:34 29 ********** 96 2018-01-17 19:35 30 *********** ... ..( 87 skipped). .. *********** 184 2018-01-17 21:03 30 *********** 185 2018-01-17 21:04 29 ********** ... ..( 79 skipped). .. ********** 265 2018-01-17 22:24 29 ********** 266 2018-01-17 22:25 30 *********** ... ..( 60 skipped). .. *********** 327 2018-01-17 23:26 30 *********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 14 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 12 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 18663 Vendor specific /dev/sdc === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F3 Device Model: SAMSUNG HD103SJ Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AJ10001 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Jan 17 23:26:40 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 9180) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 153) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 16 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 071 070 025 - 8947 4 Start_Stop_Count -O--CK 097 097 000 - 3893 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 41237 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2479 191 G-Sense_Error_Rate -O---K 100 100 000 - 59 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 053 000 - 31 (Min/Max 20/47) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 7 223 Load_Retry_Count -O--CK 252 252 000 - 0 225 Load_Cycle_Count -O--CK 100 100 000 - 3989 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 30/31 Celsius Lifetime Min/Max Temperature: 22/62 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (58) Index Estimated Time Temperature Celsius 59 2018-01-17 12:50 32 ************* ... ..( 11 skipped). .. ************* 71 2018-01-17 13:50 32 ************* 72 2018-01-17 13:55 30 *********** 73 2018-01-17 14:00 30 *********** 74 2018-01-17 14:05 30 *********** 75 2018-01-17 14:10 31 ************ ... ..( 55 skipped). .. ************ 3 2018-01-17 18:50 31 ************ 4 2018-01-17 18:55 30 *********** 5 2018-01-17 19:00 30 *********** 6 2018-01-17 19:05 30 *********** 7 2018-01-17 19:10 31 ************ ... ..( 17 skipped). .. ************ 25 2018-01-17 20:40 31 ************ 26 2018-01-17 20:45 30 *********** ... ..( 8 skipped). .. *********** 35 2018-01-17 21:30 30 *********** 36 2018-01-17 21:35 31 ************ 37 2018-01-17 21:40 31 ************ 38 2018-01-17 21:45 30 *********** 39 2018-01-17 21:50 30 *********** 40 2018-01-17 21:55 31 ************ ... ..( 17 skipped). .. ************ 58 2018-01-17 23:25 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 16 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 11 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdd === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST2000DM001-1CH164 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC24 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jan 17 23:26:41 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 617) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 272) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 105 083 006 - 121904792 3 Spin_Up_Time PO---- 095 094 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1947 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 264 7 Seek_Error_Rate POSR-- 067 052 030 - 344034351378 9 Power_On_Hours -O--CK 074 074 000 - 23223 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1912 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 4552 188 Command_Timeout -O--CK 100 098 000 - 0 0 34 189 High_Fly_Writes -O-RCK 096 096 000 - 4 190 Airflow_Temperature_Cel -O---K 068 051 045 - 32 (Min/Max 31/33) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 161 193 Load_Cycle_Count -O--CK 075 075 000 - 51720 194 Temperature_Celsius -O---K 032 049 000 - 32 (0 20 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 22662h+57m+01.707s 241 Total_LBAs_Written ------ 100 253 000 - 69144030653 242 Total_LBAs_Read ------ 100 253 000 - 75198906004 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbd GPL VS 512 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 4552 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4552 [11] occurred at disk power-on lifetime: 21845 hours (910 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c2 a4 a7 c8 00 00 Error: WP at LBA = 0xc2a4a7c8 = 3265570760 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 20 00 00 14 35 73 40 40 00 00:06:17.824 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 00 0c 8b c0 40 00 00:06:17.372 WRITE FPDMA QUEUED 61 00 00 00 18 00 00 00 0c 8f e0 40 00 00:06:17.356 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 00 0c 8f f8 40 00 00:06:17.356 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 00 0c 90 80 40 00 00:06:17.355 WRITE FPDMA QUEUED Error 4551 [10] occurred at disk power-on lifetime: 21845 hours (910 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c2 a4 a7 c8 00 00 Error: WP at LBA = 0xc2a4a7c8 = 3265570760 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 20 00 00 14 35 73 20 40 00 00:06:14.760 WRITE FPDMA QUEUED 60 00 00 00 08 00 00 c2 a4 a7 c8 40 00 00:06:14.374 READ FPDMA QUEUED 60 00 00 00 50 00 00 c2 a4 a7 d8 40 00 00:06:14.324 READ FPDMA QUEUED 61 00 00 01 00 00 00 0f e3 bf 80 40 00 00:06:14.305 WRITE FPDMA QUEUED 61 00 00 01 00 00 00 0f e3 be 80 40 00 00:06:14.305 WRITE FPDMA QUEUED Error 4550 [9] occurred at disk power-on lifetime: 21845 hours (910 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c2 a4 a7 c8 00 00 Error: UNC at LBA = 0xc2a4a7c8 = 3265570760 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 08 92 a6 30 40 00 00:06:11.399 READ FPDMA QUEUED 60 00 00 00 08 00 00 c2 a4 a7 c8 40 00 00:06:11.333 READ FPDMA QUEUED 60 00 00 00 08 00 00 c2 a4 a7 c0 40 00 00:06:11.333 READ FPDMA QUEUED 60 00 00 00 08 00 00 c2 a4 a7 b8 40 00 00:06:11.333 READ FPDMA QUEUED 60 00 00 00 08 00 00 c2 a4 a7 b0 40 00 00:06:11.332 READ FPDMA QUEUED Error 4549 [8] occurred at disk power-on lifetime: 21845 hours (910 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c2 a4 a7 c8 00 00 Error: UNC at LBA = 0xc2a4a7c8 = 3265570760 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 c2 a4 a7 28 40 00 00:06:08.123 READ FPDMA QUEUED 60 00 00 01 00 00 00 c2 a4 a6 28 40 00 00:06:08.122 READ FPDMA QUEUED 60 00 00 01 00 00 00 8d 89 5a 48 40 00 00:06:08.122 READ FPDMA QUEUED 60 00 00 01 00 00 00 8d 89 59 48 40 00 00:06:08.121 READ FPDMA QUEUED 60 00 00 01 00 00 00 c2 a4 a5 28 40 00 00:06:08.120 READ FPDMA QUEUED Error 4548 [7] occurred at disk power-on lifetime: 21787 hours (907 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c2 a4 a7 c8 00 00 Error: UNC at LBA = 0xc2a4a7c8 = 3265570760 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 18 95 2c 78 40 00 07:22:27.236 READ FPDMA QUEUED 60 00 00 01 00 00 00 18 95 2b 78 40 00 07:22:27.236 READ FPDMA QUEUED 60 00 00 01 00 00 00 18 95 2a 78 40 00 07:22:27.236 READ FPDMA QUEUED 60 00 00 01 00 00 00 18 95 29 78 40 00 07:22:27.236 READ FPDMA QUEUED 60 00 00 01 00 00 00 18 95 28 78 40 00 07:22:27.236 READ FPDMA QUEUED Error 4547 [6] occurred at disk power-on lifetime: 21787 hours (907 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c2 a4 a7 c8 00 00 Error: WP at LBA = 0xc2a4a7c8 = 3265570760 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 20 00 00 21 d0 be e0 40 00 07:21:29.336 WRITE FPDMA QUEUED 60 00 00 00 20 00 00 15 9d ba 80 40 00 07:21:29.335 READ FPDMA QUEUED 61 00 00 00 20 00 00 21 d0 be c0 40 00 07:21:29.334 WRITE FPDMA QUEUED 60 00 00 00 20 00 00 15 9d ba 60 40 00 07:21:29.332 READ FPDMA QUEUED 61 00 00 00 20 00 00 21 d0 be a0 40 00 07:21:29.332 WRITE FPDMA QUEUED Error 4546 [5] occurred at disk power-on lifetime: 21787 hours (907 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c2 a4 a7 c8 00 00 Error: WP at LBA = 0xc2a4a7c8 = 3265570760 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 20 00 00 21 b4 f3 00 40 00 07:19:22.963 WRITE FPDMA QUEUED 60 00 00 00 20 00 00 1e 82 e2 20 40 00 07:19:22.962 READ FPDMA QUEUED 61 00 00 00 20 00 00 21 b4 f2 e0 40 00 07:19:22.961 WRITE FPDMA QUEUED 60 00 00 00 20 00 00 1e 82 e2 00 40 00 07:19:22.959 READ FPDMA QUEUED 61 00 00 00 20 00 00 21 b4 f2 c0 40 00 07:19:22.959 WRITE FPDMA QUEUED Error 4545 [4] occurred at disk power-on lifetime: 21743 hours (905 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 c2 a4 a7 c8 00 00 Error: UNC at LBA = 0xc2a4a7c8 = 3265570760 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 c2 a4 a7 c8 40 00 1d+00:16:43.169 READ FPDMA QUEUED 61 00 00 00 40 00 00 00 12 ae 00 40 00 1d+00:16:43.169 WRITE FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 e0 00 1d+00:16:43.076 READ LOG EXT 60 00 00 00 08 00 00 c2 a4 a7 c8 40 00 1d+00:16:40.214 READ FPDMA QUEUED 61 00 00 00 08 00 00 00 6a d6 58 40 00 1d+00:16:40.214 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 32/33 Celsius Lifetime Min/Max Temperature: 20/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sde === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue (SATA) Device Model: WDC WD3200AAKS-00G3A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 40.00A40 User Capacity: 320,071,851,520 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Wed Jan 17 23:26:42 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6180) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 75) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 0 3 Spin_Up_Time PO---- 160 152 021 - 2991 4 Start_Stop_Count -O--CK 096 096 000 - 4200 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 000 - 0 9 Power_On_Hours -O--CK 032 032 000 - 49746 10 Spin_Retry_Count -O--C- 100 100 000 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3656 192 Power-Off_Retract_Count -O--CK 200 200 000 - 648 193 Load_Cycle_Count -O--CK 199 199 000 - 4199 194 Temperature_Celsius -O---K 111 095 000 - 32 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 31/32 Celsius Lifetime Min/Max Temperature: 32/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (11) Index Estimated Time Temperature Celsius 12 2018-01-17 21:19 32 ************* ... ..(126 skipped). .. ************* 11 2018-01-17 23:26 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 13 Device-to-host register FISes sent due to a COMRESET 0x8000 4 18669 Vendor specific