/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.11.0-17-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue (SATA) Device Model: WDC WD6400AAKS-65A7B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.03B01 User Capacity: 640,135,028,736 bytes [640 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sat May 29 17:02:29 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 127) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 84 3 Spin_Up_Time POS--K 153 144 021 - 5308 4 Start_Stop_Count -O--CK 091 091 000 - 9714 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 082 082 000 - 13708 10 Spin_Retry_Count -O--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 051 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 6248 192 Power-Off_Retract_Count -O--CK 200 200 000 - 622 193 Load_Cycle_Count -O--CK 197 197 000 - 9714 194 Temperature_Celsius -O---K 113 099 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 75 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 75 [2] occurred at disk power-on lifetime: 1484 hours (61 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 8f 00 ed e7 40 00 Error: UNC at LBA = 0x18f00ede7 = 6694170087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 78 00 00 01 ed 8f df 40 00 00:38:58.208 READ FPDMA QUEUED ef 00 03 00 46 00 00 00 00 00 00 40 00 00:38:57.325 SET FEATURES [Set transfer mode] c6 00 00 00 10 00 00 00 00 00 00 40 00 00:38:57.325 SET MULTIPLE MODE 60 00 20 00 70 00 00 01 ed 8f df 40 00 00:38:54.221 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:54.221 READ LOG EXT Error 74 [1] occurred at disk power-on lifetime: 1484 hours (61 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 8f 00 ed e7 40 00 Error: UNC at LBA = 0x18f00ede7 = 6694170087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 70 00 00 01 ed 8f df 40 00 00:38:54.221 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:54.221 READ LOG EXT 60 00 20 00 68 00 00 01 ed 8f df 40 00 00:38:51.066 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:51.066 READ LOG EXT 60 00 20 00 60 00 00 01 ed 8f df 40 00 00:38:47.903 READ FPDMA QUEUED Error 73 [0] occurred at disk power-on lifetime: 1484 hours (61 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 8f 00 ed e7 40 00 Error: UNC at LBA = 0x18f00ede7 = 6694170087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 68 00 00 01 ed 8f df 40 00 00:38:51.066 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:51.066 READ LOG EXT 60 00 20 00 60 00 00 01 ed 8f df 40 00 00:38:47.903 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:47.903 READ LOG EXT 60 00 20 00 58 00 00 01 ed 8f df 40 00 00:38:44.914 READ FPDMA QUEUED Error 72 [23] occurred at disk power-on lifetime: 1484 hours (61 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 8f 00 ed e7 40 00 Error: UNC at LBA = 0x18f00ede7 = 6694170087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 60 00 00 01 ed 8f df 40 00 00:38:47.903 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:47.903 READ LOG EXT 60 00 20 00 58 00 00 01 ed 8f df 40 00 00:38:44.914 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:44.914 READ LOG EXT 60 00 20 00 50 00 00 01 ed 8f df 40 00 00:38:41.426 READ FPDMA QUEUED Error 71 [22] occurred at disk power-on lifetime: 1484 hours (61 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 8f 00 ed e7 40 00 Error: UNC at LBA = 0x18f00ede7 = 6694170087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 58 00 00 01 ed 8f df 40 00 00:38:44.914 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:44.914 READ LOG EXT 60 00 20 00 50 00 00 01 ed 8f df 40 00 00:38:41.426 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:41.426 READ LOG EXT 60 00 20 00 48 00 00 01 ed 8f df 40 00 00:38:38.438 READ FPDMA QUEUED Error 70 [21] occurred at disk power-on lifetime: 1484 hours (61 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 8f 00 ed e7 40 00 Error: UNC at LBA = 0x18f00ede7 = 6694170087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 50 00 00 01 ed 8f df 40 00 00:38:41.426 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:41.426 READ LOG EXT 60 00 20 00 48 00 00 01 ed 8f df 40 00 00:38:38.438 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:38.437 READ LOG EXT 60 00 20 00 40 00 00 01 ed 8f df 40 00 00:38:35.283 READ FPDMA QUEUED Error 69 [20] occurred at disk power-on lifetime: 1484 hours (61 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 8f 00 ed e7 40 00 Error: UNC at LBA = 0x18f00ede7 = 6694170087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 48 00 00 01 ed 8f df 40 00 00:38:38.438 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:38.437 READ LOG EXT 60 00 20 00 40 00 00 01 ed 8f df 40 00 00:38:35.283 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:35.282 READ LOG EXT 60 00 20 00 30 00 00 01 ed 8f df 40 00 00:38:32.125 READ FPDMA QUEUED Error 68 [19] occurred at disk power-on lifetime: 1484 hours (61 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 8f 00 ed e7 40 00 Error: UNC at LBA = 0x18f00ede7 = 6694170087 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 40 00 00 01 ed 8f df 40 00 00:38:35.283 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:38:35.282 READ LOG EXT 60 00 20 00 30 00 00 01 ed 8f df 40 00 00:38:32.125 READ FPDMA QUEUED 61 00 60 00 28 00 00 2b 23 41 af 40 00 00:38:31.242 WRITE FPDMA QUEUED 61 01 00 00 20 00 00 2b 23 40 af 40 00 00:38:31.242 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short captive Interrupted (host reset) 90% 8853 - # 2 Short offline Completed without error 00% 8832 - # 3 Short captive Completed without error 00% 8832 - # 4 Short captive Completed without error 00% 5338 - # 5 Short offline Completed without error 00% 5337 - # 6 Extended captive Interrupted (host reset) 90% 5337 - # 7 Short offline Completed without error 00% 3684 - # 8 Short offline Completed: read failure 90% 929 32346087 # 9 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 19/34 Celsius Lifetime Min/Max Temperature: 19/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (60) Index Estimated Time Temperature Celsius 61 2021-05-29 14:55 32 ************* ... ..( 2 skipped). .. ************* 64 2021-05-29 14:58 32 ************* 65 2021-05-29 14:59 33 ************** ... ..( 18 skipped). .. ************** 84 2021-05-29 15:18 33 ************** 85 2021-05-29 15:19 34 *************** ... ..( 33 skipped). .. *************** 119 2021-05-29 15:53 34 *************** 120 2021-05-29 15:54 ? - 121 2021-05-29 15:55 19 - 122 2021-05-29 15:56 19 - 123 2021-05-29 15:57 20 * 124 2021-05-29 15:58 21 ** 125 2021-05-29 15:59 21 ** 126 2021-05-29 16:00 22 *** 127 2021-05-29 16:01 22 *** 0 2021-05-29 16:02 23 **** 1 2021-05-29 16:03 24 ***** 2 2021-05-29 16:04 25 ****** 3 2021-05-29 16:05 25 ****** 4 2021-05-29 16:06 26 ******* 5 2021-05-29 16:07 26 ******* 6 2021-05-29 16:08 26 ******* 7 2021-05-29 16:09 27 ******** 8 2021-05-29 16:10 27 ******** 9 2021-05-29 16:11 28 ********* 10 2021-05-29 16:12 29 ********** ... ..( 2 skipped). .. ********** 13 2021-05-29 16:15 29 ********** 14 2021-05-29 16:16 30 *********** ... ..( 3 skipped). .. *********** 18 2021-05-29 16:20 30 *********** 19 2021-05-29 16:21 31 ************ 20 2021-05-29 16:22 31 ************ 21 2021-05-29 16:23 31 ************ 22 2021-05-29 16:24 32 ************* ... ..( 3 skipped). .. ************* 26 2021-05-29 16:28 32 ************* 27 2021-05-29 16:29 33 ************** ... ..( 11 skipped). .. ************** 39 2021-05-29 16:41 33 ************** 40 2021-05-29 16:42 34 *************** ... ..( 19 skipped). .. *************** 60 2021-05-29 17:02 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 4084 Vendor specific /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.11.0-17-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 850 EVO 250GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EMT03B6Q User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat May 29 17:02:29 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 133) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 097 097 000 - 14956 12 Power_Cycle_Count -O--CK 098 098 000 - 1458 177 Wear_Leveling_Count PO--C- 097 097 000 - 56 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 073 055 000 - 27 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 51 241 Total_LBAs_Written -O--CK 099 099 000 - 36507514651 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 24/26 Celsius Lifetime Min/Max Temperature: 17/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (40) Index Estimated Time Temperature Celsius 41 2021-05-28 19:50 25 ****** 42 2021-05-28 20:00 25 ****** 43 2021-05-28 20:10 24 ***** ... ..( 3 skipped). .. ***** 47 2021-05-28 20:50 24 ***** 48 2021-05-28 21:00 23 **** ... ..( 11 skipped). .. **** 60 2021-05-28 23:00 23 **** 61 2021-05-28 23:10 24 ***** 62 2021-05-28 23:20 24 ***** 63 2021-05-28 23:30 ? - 64 2021-05-28 23:40 25 ****** 65 2021-05-28 23:50 23 **** 66 2021-05-29 00:00 23 **** 67 2021-05-29 00:10 24 ***** 68 2021-05-29 00:20 ? - 69 2021-05-29 00:30 24 ***** 70 2021-05-29 00:40 25 ****** 71 2021-05-29 00:50 24 ***** ... ..( 4 skipped). .. ***** 76 2021-05-29 01:40 24 ***** 77 2021-05-29 01:50 23 **** 78 2021-05-29 02:00 23 **** 79 2021-05-29 02:10 23 **** 80 2021-05-29 02:20 22 *** ... ..( 3 skipped). .. *** 84 2021-05-29 03:00 22 *** 85 2021-05-29 03:10 23 **** 86 2021-05-29 03:20 22 *** 87 2021-05-29 03:30 ? - 88 2021-05-29 03:40 ? - 89 2021-05-29 03:50 22 *** 90 2021-05-29 04:00 25 ****** 91 2021-05-29 04:10 24 ***** 92 2021-05-29 04:20 ? - 93 2021-05-29 04:30 21 ** 94 2021-05-29 04:40 23 **** 95 2021-05-29 04:50 26 ******* 96 2021-05-29 05:00 26 ******* 97 2021-05-29 05:10 25 ****** 98 2021-05-29 05:20 28 ********* 99 2021-05-29 05:30 24 ***** ... ..( 2 skipped). .. ***** 102 2021-05-29 06:00 24 ***** 103 2021-05-29 06:10 23 **** 104 2021-05-29 06:20 23 **** 105 2021-05-29 06:30 22 *** ... ..( 2 skipped). .. *** 108 2021-05-29 07:00 22 *** 109 2021-05-29 07:10 23 **** 110 2021-05-29 07:20 23 **** 111 2021-05-29 07:30 23 **** 112 2021-05-29 07:40 22 *** 113 2021-05-29 07:50 22 *** 114 2021-05-29 08:00 22 *** 115 2021-05-29 08:10 ? - 116 2021-05-29 08:20 23 **** 117 2021-05-29 08:30 23 **** 118 2021-05-29 08:40 24 ***** 119 2021-05-29 08:50 25 ****** 120 2021-05-29 09:00 29 ********** 121 2021-05-29 09:10 30 *********** ... ..( 11 skipped). .. *********** 5 2021-05-29 11:10 30 *********** 6 2021-05-29 11:20 ? - 7 2021-05-29 11:30 27 ******** 8 2021-05-29 11:40 27 ******** 9 2021-05-29 11:50 ? - ... ..( 3 skipped). .. - 13 2021-05-29 12:30 ? - 14 2021-05-29 12:40 26 ******* 15 2021-05-29 12:50 26 ******* 16 2021-05-29 13:00 26 ******* 17 2021-05-29 13:10 ? - 18 2021-05-29 13:20 26 ******* 19 2021-05-29 13:30 26 ******* 20 2021-05-29 13:40 ? - 21 2021-05-29 13:50 25 ****** 22 2021-05-29 14:00 28 ********* 23 2021-05-29 14:10 26 ******* 24 2021-05-29 14:20 24 ***** 25 2021-05-29 14:30 24 ***** 26 2021-05-29 14:40 ? - 27 2021-05-29 14:50 24 ***** 28 2021-05-29 15:00 24 ***** 29 2021-05-29 15:10 24 ***** 30 2021-05-29 15:20 25 ****** ... ..( 2 skipped). .. ****** 33 2021-05-29 15:50 25 ****** 34 2021-05-29 16:00 ? - 35 2021-05-29 16:10 24 ***** 36 2021-05-29 16:20 24 ***** 37 2021-05-29 16:30 24 ***** 38 2021-05-29 16:40 25 ****** 39 2021-05-29 16:50 25 ****** 40 2021-05-29 17:00 26 ******* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.11.0-17-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 850 EVO 250GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: EMT02B6Q User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat May 29 17:02:29 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 133) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 098 098 000 - 6383 12 Power_Cycle_Count -O--CK 098 098 000 - 1337 177 Wear_Leveling_Count PO--C- 098 098 000 - 26 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 072 051 000 - 28 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 1335 241 Total_LBAs_Written -O--CK 099 099 000 - 7045497833 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 24/27 Celsius Lifetime Min/Max Temperature: 18/66 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (37) Index Estimated Time Temperature Celsius 38 2021-05-28 19:50 ? - 39 2021-05-28 20:00 30 *********** 40 2021-05-28 20:10 32 ************* 41 2021-05-28 20:20 33 ************** 42 2021-05-28 20:30 34 *************** 43 2021-05-28 20:40 34 *************** 44 2021-05-28 20:50 34 *************** 45 2021-05-28 21:00 35 **************** ... ..( 2 skipped). .. **************** 48 2021-05-28 21:30 35 **************** 49 2021-05-28 21:40 36 ***************** ... ..( 4 skipped). .. ***************** 54 2021-05-28 22:30 36 ***************** 55 2021-05-28 22:40 37 ****************** ... ..( 2 skipped). .. ****************** 58 2021-05-28 23:10 37 ****************** 59 2021-05-28 23:20 ? - 60 2021-05-28 23:30 22 *** 61 2021-05-28 23:40 24 ***** 62 2021-05-28 23:50 24 ***** 63 2021-05-29 00:00 ? - 64 2021-05-29 00:10 21 ** 65 2021-05-29 00:20 23 **** 66 2021-05-29 00:30 24 ***** 67 2021-05-29 00:40 25 ****** 68 2021-05-29 00:50 25 ****** 69 2021-05-29 01:00 26 ******* ... ..( 8 skipped). .. ******* 78 2021-05-29 02:30 26 ******* 79 2021-05-29 02:40 25 ****** ... ..( 5 skipped). .. ****** 85 2021-05-29 03:40 25 ****** 86 2021-05-29 03:50 ? - 87 2021-05-29 04:00 23 **** 88 2021-05-29 04:10 24 ***** 89 2021-05-29 04:20 25 ****** 90 2021-05-29 04:30 25 ****** 91 2021-05-29 04:40 25 ****** 92 2021-05-29 04:50 26 ******* 93 2021-05-29 05:00 27 ******** ... ..( 10 skipped). .. ******** 104 2021-05-29 06:50 27 ******** 105 2021-05-29 07:00 ? - 106 2021-05-29 07:10 32 ************* 107 2021-05-29 07:20 37 ****************** 108 2021-05-29 07:30 42 *********************** 109 2021-05-29 07:40 37 ****************** 110 2021-05-29 07:50 40 ********************* 111 2021-05-29 08:00 35 **************** 112 2021-05-29 08:10 34 *************** ... ..( 12 skipped). .. *************** 125 2021-05-29 10:20 34 *************** 126 2021-05-29 10:30 35 **************** ... ..( 4 skipped). .. **************** 3 2021-05-29 11:20 35 **************** 4 2021-05-29 11:30 ? - 5 2021-05-29 11:40 31 ************ 6 2021-05-29 11:50 32 ************* 7 2021-05-29 12:00 34 *************** 8 2021-05-29 12:10 33 ************** 9 2021-05-29 12:20 34 *************** ... ..( 3 skipped). .. *************** 13 2021-05-29 13:00 34 *************** 14 2021-05-29 13:10 35 **************** 15 2021-05-29 13:20 34 *************** 16 2021-05-29 13:30 35 **************** 17 2021-05-29 13:40 35 **************** 18 2021-05-29 13:50 ? - 19 2021-05-29 14:00 ? - 20 2021-05-29 14:10 27 ******** 21 2021-05-29 14:20 27 ******** 22 2021-05-29 14:30 ? - 23 2021-05-29 14:40 ? - 24 2021-05-29 14:50 26 ******* 25 2021-05-29 15:00 27 ******** ... ..( 4 skipped). .. ******** 30 2021-05-29 15:50 27 ******** 31 2021-05-29 16:00 ? - 32 2021-05-29 16:10 24 ***** 33 2021-05-29 16:20 25 ****** 34 2021-05-29 16:30 27 ******** ... ..( 2 skipped). .. ******** 37 2021-05-29 17:00 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdd smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.11.0-17-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3320820AS Serial Number: -- Firmware Version: 3.AAC User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sat May 29 17:02:29 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 115) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 101 086 006 - 44791296 3 Spin_Up_Time PO---- 096 095 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3788 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 083 060 030 - 227539805 9 Power_On_Hours -O--CK 092 092 000 - 7264 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1506 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 064 033 045 Past 36 (Min/Max 19/36) 194 Temperature_Celsius -O---K 036 067 000 - 36 (0 13 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 062 052 000 - 162702626 197 Current_Pending_Sector -O--C- 100 100 000 - 1 198 Offline_Uncorrectable ----C- 100 100 000 - 1 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 4633 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 097 250 000 - 3 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS