/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Maxtor DiamondMax 23 Device Model: STM3500418AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC35 User Capacity: 500 107 862 016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue May 16 12:59:04 2017 +10 ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213911en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 92) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 118 090 006 - 171148811 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 092 092 020 - 8613 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 084 060 030 - 4565424276 9 Power_On_Hours -O--CK 080 080 000 - 18203 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 097 097 020 - 3678 183 Runtime_Bad_Block -O--CK 001 001 000 - 4056 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 360 188 Command_Timeout -O--CK 100 090 000 - 4295032879 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 073 053 045 - 27 (Min/Max 17/28) 194 Temperature_Celsius -O---K 027 047 000 - 27 (0 14 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 039 016 000 - 171148811 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 185 000 - 224692 240 Head_Flying_Hours ------ 100 253 000 - 27827 (118 215 0) 241 Total_LBAs_Written ------ 100 253 000 - 1321267550 242 Total_LBAs_Read ------ 100 253 000 - 2064887228 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL,SL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 355 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 355 [14] occurred at disk power-on lifetime: 14827 hours (617 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3f 00 00 03 00 00 Error: UNC at LBA = 0x3f000003 = 1056964611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:21:22.391 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 02 e0 00 09:21:21.662 READ DMA EXT 25 00 00 00 04 00 00 00 00 00 07 e0 00 09:21:21.662 READ DMA EXT 25 00 00 00 01 00 00 3e 00 00 c1 e0 00 09:21:21.635 READ DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 09:21:21.635 READ DMA EXT Error 354 [13] occurred at disk power-on lifetime: 14827 hours (617 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3f 00 00 03 00 00 Error: UNC at LBA = 0x3f000003 = 1056964611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:32.631 READ DMA EXT 35 00 00 00 08 00 0c f7 00 dd f8 e0 00 09:18:32.630 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:32.569 IDENTIFY DEVICE 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:29.892 READ DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:29.892 FLUSH CACHE EXT Error 353 [12] occurred at disk power-on lifetime: 14827 hours (617 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3f 00 00 03 00 00 Error: UNC at LBA = 0x3f000003 = 1056964611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:29.892 READ DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:29.892 FLUSH CACHE EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:29.764 IDENTIFY DEVICE 35 00 00 00 08 00 0c f8 00 dd 80 e0 00 09:18:29.763 WRITE DMA EXT 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:27.122 READ DMA EXT Error 352 [11] occurred at disk power-on lifetime: 14827 hours (617 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3f 00 00 03 00 00 Error: UNC at LBA = 0x3f000003 = 1056964611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:27.122 READ DMA EXT 35 00 00 00 08 00 0c f9 00 80 50 e0 00 09:18:27.121 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:27.033 IDENTIFY DEVICE 35 00 00 00 08 00 0c 87 00 82 70 e0 00 09:18:27.032 WRITE DMA EXT 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:24.405 READ DMA EXT Error 351 [10] occurred at disk power-on lifetime: 14827 hours (617 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3f 00 00 03 00 00 Error: UNC at LBA = 0x3f000003 = 1056964611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:24.405 READ DMA EXT 35 00 00 00 08 00 0c f7 00 dd f0 e0 00 09:18:24.405 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:24.327 IDENTIFY DEVICE 35 00 00 00 07 00 13 dc 00 88 70 e0 00 09:18:24.327 WRITE DMA EXT 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:21.658 READ DMA EXT Error 350 [9] occurred at disk power-on lifetime: 14827 hours (617 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3f 00 00 03 00 00 Error: UNC at LBA = 0x3f000003 = 1056964611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:21.658 READ DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:21.658 FLUSH CACHE EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:21.642 IDENTIFY DEVICE 35 00 00 00 08 00 0c f8 00 dd 00 e0 00 09:18:21.641 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:21.496 IDENTIFY DEVICE Error 349 [8] occurred at disk power-on lifetime: 14827 hours (617 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3f 00 00 03 00 00 Error: UNC at LBA = 0x3f000003 = 1056964611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:18.871 READ DMA EXT 35 00 00 00 08 00 0c 7d 00 e1 c8 e0 00 09:18:18.870 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:18.782 IDENTIFY DEVICE 35 00 00 00 08 00 0c 7d 00 e1 90 e0 00 09:18:18.782 WRITE DMA EXT 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:16.121 READ DMA EXT Error 348 [7] occurred at disk power-on lifetime: 14827 hours (617 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 3f 00 00 03 00 00 Error: UNC at LBA = 0x3f000003 = 1056964611 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 10 00 00 3f 00 00 00 e0 00 09:18:16.121 READ DMA EXT 35 00 00 00 08 00 0c 74 00 e1 a8 e0 00 09:18:16.121 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 09:18:16.060 IDENTIFY DEVICE 35 00 00 00 08 00 0c cc 00 e0 60 e0 00 09:18:16.060 WRITE DMA EXT 35 00 00 00 08 00 0c 96 00 e0 a0 e0 00 09:18:16.059 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 17/28 Celsius Lifetime Min/Max Temperature: 14/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (15) Index Estimated Time Temperature Celsius 16 2017-05-11 07:58 28 ********* 17 2017-05-11 08:57 27 ******** 18 2017-05-11 09:56 27 ******** 19 2017-05-11 10:55 27 ******** 20 2017-05-11 11:54 ? - 21 2017-05-11 12:53 20 * 22 2017-05-11 13:52 20 * 23 2017-05-11 14:51 ? - 24 2017-05-11 15:50 19 - 25 2017-05-11 16:49 19 - 26 2017-05-11 17:48 28 ********* 27 2017-05-11 18:47 28 ********* 28 2017-05-11 19:46 ? - 29 2017-05-11 20:45 18 - 30 2017-05-11 21:44 18 - 31 2017-05-11 22:43 27 ******** ... ..( 3 skipped). .. ******** 35 2017-05-12 02:39 27 ******** 36 2017-05-12 03:38 26 ******* 37 2017-05-12 04:37 27 ******** 38 2017-05-12 05:36 26 ******* 39 2017-05-12 06:35 26 ******* 40 2017-05-12 07:34 ? - 41 2017-05-12 08:33 18 - 42 2017-05-12 09:32 18 - 43 2017-05-12 10:31 28 ********* 44 2017-05-12 11:30 27 ******** 45 2017-05-12 12:29 27 ******** 46 2017-05-12 13:28 ? - 47 2017-05-12 14:27 18 - 48 2017-05-12 15:26 18 - 49 2017-05-12 16:25 ? - 50 2017-05-12 17:24 18 - 51 2017-05-12 18:23 18 - 52 2017-05-12 19:22 27 ******** 53 2017-05-12 20:21 26 ******* 54 2017-05-12 21:20 26 ******* 55 2017-05-12 22:19 28 ********* 56 2017-05-12 23:18 27 ******** 57 2017-05-13 00:17 ? - 58 2017-05-13 01:16 17 - 59 2017-05-13 02:15 17 - 60 2017-05-13 03:14 26 ******* 61 2017-05-13 04:13 27 ******** 62 2017-05-13 05:12 26 ******* 63 2017-05-13 06:11 26 ******* 64 2017-05-13 07:10 ? - 65 2017-05-13 08:09 19 - 66 2017-05-13 09:08 19 - 67 2017-05-13 10:07 27 ******** 68 2017-05-13 11:06 27 ******** 69 2017-05-13 12:05 28 ********* 70 2017-05-13 13:04 27 ******** ... ..( 2 skipped). .. ******** 73 2017-05-13 16:01 27 ******** 74 2017-05-13 17:00 ? - 75 2017-05-13 17:59 17 - 76 2017-05-13 18:58 17 - 77 2017-05-13 19:57 27 ******** 78 2017-05-13 20:56 ? - 79 2017-05-13 21:55 19 - 80 2017-05-13 22:54 19 - 81 2017-05-13 23:53 27 ******** ... ..( 3 skipped). .. ******** 85 2017-05-14 03:49 27 ******** 86 2017-05-14 04:48 26 ******* 87 2017-05-14 05:47 28 ********* 88 2017-05-14 06:46 27 ******** 89 2017-05-14 07:45 26 ******* 90 2017-05-14 08:44 ? - 91 2017-05-14 09:43 17 - 92 2017-05-14 10:42 17 - 93 2017-05-14 11:41 25 ****** 94 2017-05-14 12:40 26 ******* ... ..( 7 skipped). .. ******* 102 2017-05-14 20:32 26 ******* 103 2017-05-14 21:31 27 ******** ... ..( 5 skipped). .. ******** 109 2017-05-15 03:25 27 ******** 110 2017-05-15 04:24 ? - 111 2017-05-15 05:23 18 - 112 2017-05-15 06:22 18 - 113 2017-05-15 07:21 ? - 114 2017-05-15 08:20 18 - 115 2017-05-15 09:19 18 - 116 2017-05-15 10:18 26 ******* 117 2017-05-15 11:17 26 ******* 118 2017-05-15 12:16 ? - 119 2017-05-15 13:15 27 ******** 120 2017-05-15 14:14 27 ******** 121 2017-05-15 15:13 27 ******** 122 2017-05-15 16:12 28 ********* 123 2017-05-15 17:11 ? - 124 2017-05-15 18:10 28 ********* 125 2017-05-15 19:09 ? - 126 2017-05-15 20:08 27 ******** 127 2017-05-15 21:07 27 ******** 0 2017-05-15 22:06 ? - 1 2017-05-15 23:05 27 ******** 2 2017-05-16 00:04 ? - 3 2017-05-16 01:03 27 ******** 4 2017-05-16 02:02 ? - 5 2017-05-16 03:01 26 ******* 6 2017-05-16 04:00 ? - 7 2017-05-16 04:59 27 ******** 8 2017-05-16 05:58 ? - 9 2017-05-16 06:57 17 - 10 2017-05-16 07:56 17 - 11 2017-05-16 08:55 28 ********* 12 2017-05-16 09:54 27 ******** ... ..( 2 skipped). .. ******** 15 2017-05-16 12:51 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 14 Device-to-host register FISes sent due to a COMRESET 0x0001 2 65535+ Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 65535+ R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 176 R_ERR response for host-to-device non-data FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus Device Model: ST380013AS Serial Number: -- Firmware Version: 3.18 User Capacity: 80 025 280 000 bytes [80,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 T13/1410D revision 2 Local Time is: Tue May 16 12:59:04 2017 +10 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 58) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 063 051 006 - 88512434 3 Spin_Up_Time PO---- 098 097 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3483 5 Reallocated_Sector_Ct PO--CK 099 099 036 - 65 7 Seek_Error_Rate POSR-- 089 060 030 - 882614173 9 Power_On_Hours -O--CK 038 038 000 - 54715 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 065 065 020 - 36840 194 Temperature_Celsius -O---K 037 056 000 - 37 195 Hardware_ECC_Recovered -O-RC- 063 051 000 - 88512434 197 Current_Pending_Sector -O--C- 100 100 000 - 2 198 Offline_Uncorrectable ----C- 100 100 000 - 2 199 UDMA_CRC_Error_Count -OSRCK 200 199 000 - 1 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 SL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 SL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x20 SL R/O 1 Streaming performance log [OBS-8] 0x21 SL R/O 1 Write stream error log 0x22 SL R/O 1 Read stream error log 0x23 SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f SL R/W 16 Host vendor specific log 0xa0 SL VS 1 Device vendor specific log 0xa1 SL VS 20 Device vendor specific log 0xa2 SL VS 101 Device vendor specific log 0xa8 SL VS 20 Device vendor specific log 0xa9 SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 608 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 608 occurred at disk power-on lifetime: 2541 hours (105 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 9f 3f 2a ca 40 Error: UNC 159 sectors at LBA = 0x00ca2a3f = 13249087 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 a0 29 ca 40 00 01:14:20.266 READ DMA c8 00 00 a0 28 ca 40 00 01:14:20.263 READ DMA c8 00 00 a0 27 ca 40 00 01:14:20.296 READ DMA c8 00 00 a0 26 ca 40 00 01:14:20.295 READ DMA c8 00 00 a0 25 ca 40 00 01:14:20.291 READ DMA Error 607 occurred at disk power-on lifetime: 2316 hours (96 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 01 3f 2a ca e0 Error: UNC at LBA = 0x00ca2a3f = 13249087 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 d8 01 3f 2a ca e0 00 00:15:52.012 READ VERIFY SECTOR(S) 40 d8 02 41 2a ca e0 00 00:15:51.999 READ VERIFY SECTOR(S) c8 d8 01 00 00 00 e0 00 00:15:48.545 READ DMA 40 d8 02 3f 2a ca e0 00 00:15:48.536 READ VERIFY SECTOR(S) c8 d8 01 00 00 00 e0 00 00:15:48.528 READ DMA Error 606 occurred at disk power-on lifetime: 2316 hours (96 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 02 3f 2a ca e0 Error: UNC at LBA = 0x00ca2a3f = 13249087 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 d8 02 3f 2a ca e0 00 00:15:38.088 READ VERIFY SECTOR(S) c8 d8 01 00 00 00 e0 00 00:15:34.635 READ DMA 40 d8 04 43 2a ca e0 00 00:15:48.545 READ VERIFY SECTOR(S) c8 d8 01 00 00 00 e0 00 00:15:48.536 READ DMA 40 d8 04 3f 2a ca e0 00 00:15:48.528 READ VERIFY SECTOR(S) Error 605 occurred at disk power-on lifetime: 2316 hours (96 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 04 3f 2a ca e0 Error: UNC at LBA = 0x00ca2a3f = 13249087 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 d8 04 3f 2a ca e0 00 00:15:38.088 READ VERIFY SECTOR(S) 40 d8 08 47 2a ca e0 00 00:15:34.635 READ VERIFY SECTOR(S) c8 d8 01 00 00 00 e0 00 00:15:34.627 READ DMA 40 d8 08 3f 2a ca e0 00 00:15:34.618 READ VERIFY SECTOR(S) c8 d8 01 00 00 00 e0 00 00:15:34.599 READ DMA Error 604 occurred at disk power-on lifetime: 2316 hours (96 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 3f 2a ca e0 Error: UNC at LBA = 0x00ca2a3f = 13249087 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 40 d8 08 3f 2a ca e0 00 00:15:38.088 READ VERIFY SECTOR(S) c8 d8 01 00 00 00 e0 00 00:15:34.635 READ DMA 40 d8 10 4f 2a ca e0 00 00:15:34.627 READ VERIFY SECTOR(S) c8 d8 01 00 00 00 e0 00 00:15:34.618 READ DMA 40 d8 10 3f 2a ca e0 00 00:15:34.599 READ VERIFY SECTOR(S) SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported