/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD1600BEVT-22ZCT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 11.01A11 User Capacity: 160,041,885,696 bytes [160 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Dec 24 12:06:58 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4980) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 61) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 159 158 021 - 1033 4 Start_Stop_Count -O--CK 092 092 000 - 8916 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 085 085 000 - 11486 10 Spin_Retry_Count PO--CK 100 099 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 093 093 000 - 7769 192 Power-Off_Retract_Count -O--CK 200 200 000 - 422 193 Load_Cycle_Count -O--CK 160 160 000 - 120135 194 Temperature_Celsius -O---K 105 077 000 - 38 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 19 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 19 [18] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 1d 60 01 8f 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 00 01 1d 00 8f ef 00 00 00 00:00:08.200 NOP [Reserved subcommand] [OBS-ACS-2] 03 90 ef 01 81 00 08 00 20 08 00 00 00 00:01:38.704 CFA REQUEST EXTENDED ERROR 00 08 08 00 20 01 e4 03 73 60 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] Error 18 [17] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 90 60 01 81 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 00 01 90 00 81 ef 00 00 00 00:00:08.200 NOP [Reserved subcommand] [OBS-ACS-2] 03 e4 ef 01 73 00 08 00 20 08 00 00 00 00:01:35.204 CFA REQUEST EXTENDED ERROR 00 08 08 00 20 01 c4 03 66 60 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] Error 17 [16] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 e4 60 01 73 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 00 01 e4 00 73 ef 00 00 00 00:00:08.200 NOP [Reserved subcommand] [OBS-ACS-2] 03 c4 ef 01 66 00 08 00 20 08 00 00 00 00:01:31.844 CFA REQUEST EXTENDED ERROR 00 08 08 00 20 01 a3 03 59 60 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] Error 16 [15] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c4 60 01 66 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 00 01 c4 00 66 ef 00 00 00 00:00:08.200 NOP [Reserved subcommand] [OBS-ACS-2] 03 a3 ef 01 59 00 08 00 20 08 00 00 00 00:01:28.483 CFA REQUEST EXTENDED ERROR 00 08 08 00 20 01 85 03 4c 60 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] Error 15 [14] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 a3 60 01 59 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 00 01 a3 00 59 ef 00 00 00 00:00:08.200 NOP [Reserved subcommand] [OBS-ACS-2] 03 84 ef 01 4c 00 08 00 20 08 00 00 00 00:01:25.125 CFA REQUEST EXTENDED ERROR 00 08 08 00 20 01 63 03 3f 60 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] Error 14 [13] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 85 60 01 4c 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 00 01 84 00 4c ef 00 00 00 00:00:08.200 NOP [Reserved subcommand] [OBS-ACS-2] 03 63 ef 01 3f 00 08 00 20 08 00 00 00 00:01:21.763 CFA REQUEST EXTENDED ERROR 00 08 08 00 20 01 43 03 32 60 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] Error 13 [12] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 63 60 01 3f 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 00 01 63 00 3f ef 00 00 00 00:00:08.200 NOP [Reserved subcommand] [OBS-ACS-2] 03 43 ef 01 32 00 08 00 20 08 00 00 00 00:01:18.403 CFA REQUEST EXTENDED ERROR 00 08 08 00 20 01 be 03 25 60 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] Error 12 [11] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 43 60 01 32 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 02 00 00 01 43 00 32 ef 00 00 00 00:00:08.200 NOP [Reserved subcommand] [OBS-ACS-2] 03 be ef 01 25 00 08 00 20 08 00 00 00 00:01:15.198 CFA REQUEST EXTENDED ERROR 00 08 08 00 20 01 2b 03 19 60 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 26/38 Celsius Lifetime Min/Max Temperature: 38/66 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2020-12-24 09:59 42 *********************** 48 2020-12-24 10:00 43 ************************ 49 2020-12-24 10:01 44 ************************* 50 2020-12-24 10:02 44 ************************* 51 2020-12-24 10:03 45 ************************** 52 2020-12-24 10:04 45 ************************** 53 2020-12-24 10:05 46 *************************** 54 2020-12-24 10:06 46 *************************** 55 2020-12-24 10:07 47 **************************** 56 2020-12-24 10:08 47 **************************** 57 2020-12-24 10:09 48 ***************************** 58 2020-12-24 10:10 48 ***************************** 59 2020-12-24 10:11 48 ***************************** 60 2020-12-24 10:12 49 ****************************** ... ..( 3 skipped). .. ****************************** 64 2020-12-24 10:16 49 ****************************** 65 2020-12-24 10:17 50 ******************************* ... ..( 6 skipped). .. ******************************* 72 2020-12-24 10:24 50 ******************************* 73 2020-12-24 10:25 51 ******************************** ... ..( 10 skipped). .. ******************************** 84 2020-12-24 10:36 51 ******************************** 85 2020-12-24 10:37 50 ******************************* 86 2020-12-24 10:38 49 ****************************** 87 2020-12-24 10:39 ? - 88 2020-12-24 10:40 22 *** 89 2020-12-24 10:41 ? - 90 2020-12-24 10:42 19 - 91 2020-12-24 10:43 22 *** 92 2020-12-24 10:44 24 ***** 93 2020-12-24 10:45 24 ***** 94 2020-12-24 10:46 26 ******* 95 2020-12-24 10:47 27 ******** 96 2020-12-24 10:48 28 ********* 97 2020-12-24 10:49 29 ********** 98 2020-12-24 10:50 31 ************ 99 2020-12-24 10:51 32 ************* 100 2020-12-24 10:52 32 ************* 101 2020-12-24 10:53 33 ************** 102 2020-12-24 10:54 33 ************** 103 2020-12-24 10:55 35 **************** 104 2020-12-24 10:56 35 **************** 105 2020-12-24 10:57 37 ****************** 106 2020-12-24 10:58 37 ****************** 107 2020-12-24 10:59 39 ******************** 108 2020-12-24 11:00 39 ******************** 109 2020-12-24 11:01 39 ******************** 110 2020-12-24 11:02 40 ********************* ... ..( 5 skipped). .. ********************* 116 2020-12-24 11:08 40 ********************* 117 2020-12-24 11:09 41 ********************** 118 2020-12-24 11:10 40 ********************* 119 2020-12-24 11:11 41 ********************** 120 2020-12-24 11:12 41 ********************** 121 2020-12-24 11:13 ? - 122 2020-12-24 11:14 23 **** 123 2020-12-24 11:15 24 ***** 124 2020-12-24 11:16 25 ****** 125 2020-12-24 11:17 26 ******* 126 2020-12-24 11:18 27 ******** 127 2020-12-24 11:19 28 ********* 0 2020-12-24 11:20 29 ********** 1 2020-12-24 11:21 29 ********** 2 2020-12-24 11:22 30 *********** 3 2020-12-24 11:23 31 ************ 4 2020-12-24 11:24 32 ************* 5 2020-12-24 11:25 32 ************* 6 2020-12-24 11:26 33 ************** 7 2020-12-24 11:27 33 ************** 8 2020-12-24 11:28 34 *************** 9 2020-12-24 11:29 35 **************** 10 2020-12-24 11:30 35 **************** 11 2020-12-24 11:31 35 **************** 12 2020-12-24 11:32 36 ***************** 13 2020-12-24 11:33 36 ***************** 14 2020-12-24 11:34 37 ****************** 15 2020-12-24 11:35 37 ****************** 16 2020-12-24 11:36 38 ******************* 17 2020-12-24 11:37 38 ******************* 18 2020-12-24 11:38 38 ******************* 19 2020-12-24 11:39 39 ******************** 20 2020-12-24 11:40 39 ******************** 21 2020-12-24 11:41 39 ******************** 22 2020-12-24 11:42 40 ********************* 23 2020-12-24 11:43 40 ********************* 24 2020-12-24 11:44 40 ********************* 25 2020-12-24 11:45 41 ********************** 26 2020-12-24 11:46 42 *********************** 27 2020-12-24 11:47 42 *********************** 28 2020-12-24 11:48 43 ************************ 29 2020-12-24 11:49 ? - 30 2020-12-24 11:50 26 ******* 31 2020-12-24 11:51 27 ******** 32 2020-12-24 11:52 28 ********* 33 2020-12-24 11:53 29 ********** 34 2020-12-24 11:54 30 *********** 35 2020-12-24 11:55 31 ************ 36 2020-12-24 11:56 32 ************* 37 2020-12-24 11:57 33 ************** 38 2020-12-24 11:58 34 *************** 39 2020-12-24 11:59 35 **************** 40 2020-12-24 12:00 36 ***************** ... ..( 2 skipped). .. ***************** 43 2020-12-24 12:03 36 ***************** 44 2020-12-24 12:04 38 ******************* 45 2020-12-24 12:05 38 ******************* 46 2020-12-24 12:06 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x8000 4 1092 Vendor specific