/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.13.0-27-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SandForce Driven SSDs Device Model: KINGSTON SVP200S37A120G Serial Number: -- LU WWN Device Id: 5 0026b7 ... Firmware Version: 502ABBF0 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jun 6 11:09:57 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Disabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0021) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 120 120 050 - 0/0 5 Retired_Block_Count PO--CK 100 100 003 - 0 9 Power_On_Hours_and_Msec -O--CK 000 000 000 - 60465h+19m+30.000s 12 Power_Cycle_Count -O--CK 096 096 000 - 4974 171 Program_Fail_Count -O--CK 000 000 000 - 0 172 Erase_Fail_Count -O--CK 000 000 000 - 0 174 Unexpect_Power_Loss_Ct ----CK 000 000 000 - 1153 177 Wear_Range_Delta ------ 000 000 000 - 6 181 Program_Fail_Count -O--CK 000 000 000 - 0 182 Erase_Fail_Count -O--CK 000 000 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 Airflow_Temperature_Cel ------ 034 056 000 - 34 (Min/Max 15/56) 194 Temperature_Celsius -O---K 034 056 000 - 34 (Min/Max 15/56) 195 ECC_Uncorr_Error_Count --SRC- 100 100 000 - 0/0 196 Reallocated_Event_Count PO--CK 100 100 003 - 0 201 Unc_Soft_Read_Err_Rate --SRC- 100 100 000 - 0/0 204 Soft_ECC_Correct_Rate --SRC- 100 100 000 - 0/0 230 Life_Curve_Status PO--C- 100 100 000 - 100 231 SSD_Life_Left PO--C- 098 098 010 - 0 233 SandForce_Internal ------ 000 000 000 - 22499 234 SandForce_Internal -O--CK 000 000 000 - 20864 241 Lifetime_Writes_GiB -O--CK 000 000 000 - 20864 242 Lifetime_Reads_GiB -O--CK 000 000 000 - 30819 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb7 GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log not supported SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Self-test routine in progress 70% 13389 - # 2 Short offline Self-test routine in progress 20% 13389 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 26/34 Celsius Lifetime Min/Max Temperature: 15/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 0 (Unknown, should be 2) Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 0 (56) Temperature History is empty SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x0002 2 0 R_ERR response for data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.13.0-27-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.8 Device Model: ST3400832AS Serial Number: -- Firmware Version: 3.03 User Capacity: 400,088,457,216 bytes [400 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Mon Jun 6 11:09:57 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 134) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 047 045 006 - 222660189 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 1006 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 085 060 030 - 340820501 9 Power_On_Hours -O--CK 074 074 000 - 23290 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 989 194 Temperature_Celsius -O---K 041 054 000 - 41 (0 12 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 047 045 000 - 222660189 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 35 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 35 [14] occurred at disk power-on lifetime: 6899 hours (287 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 12 00 2d ae cc 1c cc e0 00 Error: UNC 18 sectors at LBA = 0x2daecc1ccc = 196206140620 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 2d ae 00 1c ba e0 00 04:41:03.986 READ DMA EXT 25 00 00 00 48 00 2d ae 00 1c b2 e0 00 04:41:00.317 READ DMA EXT 25 00 00 00 50 00 2d ae 00 1c aa e0 00 04:40:56.648 READ DMA EXT 25 00 00 00 58 00 2d ae 00 1c a2 e0 00 04:40:52.962 READ DMA EXT 25 00 00 00 60 00 2d ae 00 1c 9a e0 00 04:40:49.276 READ DMA EXT Error 34 [13] occurred at disk power-on lifetime: 6899 hours (287 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 1a 00 2d ae cc 1c cc e0 00 Error: UNC 26 sectors at LBA = 0x2daecc1ccc = 196206140620 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 48 00 2d ae 00 1c b2 e0 00 04:40:08.841 READ DMA EXT 25 00 00 00 50 00 2d ae 00 1c aa e0 00 04:41:00.317 READ DMA EXT 25 00 00 00 58 00 2d ae 00 1c a2 e0 00 04:40:56.648 READ DMA EXT 25 00 00 00 60 00 2d ae 00 1c 9a e0 00 04:40:52.962 READ DMA EXT 25 00 00 00 68 00 2d ae 00 1c 92 e0 00 04:40:49.276 READ DMA EXT Error 33 [12] occurred at disk power-on lifetime: 6899 hours (287 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 22 00 2d ae cc 1c cc e0 00 Error: UNC 34 sectors at LBA = 0x2daecc1ccc = 196206140620 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 50 00 2d ae 00 1c aa e0 00 04:40:08.841 READ DMA EXT 25 00 00 00 58 00 2d ae 00 1c a2 e0 00 04:40:05.154 READ DMA EXT 25 00 00 00 60 00 2d ae 00 1c 9a e0 00 04:40:56.648 READ DMA EXT 25 00 00 00 68 00 2d ae 00 1c 92 e0 00 04:40:52.962 READ DMA EXT 25 00 00 00 70 00 2d ae 00 1c 8a e0 00 04:40:49.276 READ DMA EXT Error 32 [11] occurred at disk power-on lifetime: 6899 hours (287 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 0a 00 2d ae cc 1c cc e0 00 Error: UNC 10 sectors at LBA = 0x2daecc1ccc = 196206140620 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 38 00 2d ae 00 1c c2 e0 00 04:41:03.986 READ DMA EXT 25 00 00 00 40 00 2d ae 00 1c ba e0 00 04:41:00.317 READ DMA EXT 25 00 00 00 48 00 2d ae 00 1c b2 e0 00 04:40:56.648 READ DMA EXT 25 00 00 00 50 00 2d ae 00 1c aa e0 00 04:40:52.962 READ DMA EXT 25 00 00 00 58 00 2d ae 00 1c a2 e0 00 04:40:49.276 READ DMA EXT Error 31 [10] occurred at disk power-on lifetime: 6899 hours (287 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 12 00 2d ae cc 1c cc e0 00 Error: UNC 18 sectors at LBA = 0x2daecc1ccc = 196206140620 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 2d ae 00 1c ba e0 00 04:41:03.986 READ DMA EXT 25 00 00 00 48 00 2d ae 00 1c b2 e0 00 04:41:00.317 READ DMA EXT 25 00 00 00 50 00 2d ae 00 1c aa e0 00 04:40:56.648 READ DMA EXT 25 00 00 00 58 00 2d ae 00 1c a2 e0 00 04:40:52.962 READ DMA EXT 25 00 00 00 60 00 2d ae 00 1c 9a e0 00 04:40:49.276 READ DMA EXT Error 30 [9] occurred at disk power-on lifetime: 6899 hours (287 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 1a 00 2d ae cc 1c cc e0 00 Error: UNC 26 sectors at LBA = 0x2daecc1ccc = 196206140620 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 48 00 2d ae 00 1c b2 e0 00 04:40:08.841 READ DMA EXT 25 00 00 00 50 00 2d ae 00 1c aa e0 00 04:41:00.317 READ DMA EXT 25 00 00 00 58 00 2d ae 00 1c a2 e0 00 04:40:56.648 READ DMA EXT 25 00 00 00 60 00 2d ae 00 1c 9a e0 00 04:40:52.962 READ DMA EXT 25 00 00 00 68 00 2d ae 00 1c 92 e0 00 04:40:49.276 READ DMA EXT Error 29 [8] occurred at disk power-on lifetime: 6899 hours (287 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 22 00 2d ae cc 1c cc e0 00 Error: UNC 34 sectors at LBA = 0x2daecc1ccc = 196206140620 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 50 00 2d ae 00 1c aa e0 00 04:40:08.841 READ DMA EXT 25 00 00 00 58 00 2d ae 00 1c a2 e0 00 04:40:05.154 READ DMA EXT 25 00 00 00 60 00 2d ae 00 1c 9a e0 00 04:40:56.648 READ DMA EXT 25 00 00 00 68 00 2d ae 00 1c 92 e0 00 04:40:52.962 READ DMA EXT 25 00 00 00 70 00 2d ae 00 1c 8a e0 00 04:40:49.276 READ DMA EXT Error 28 [7] occurred at disk power-on lifetime: 6899 hours (287 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 0a 00 2d ae cc 1c cc e0 00 Error: UNC 10 sectors at LBA = 0x2daecc1ccc = 196206140620 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 38 00 2d ae 00 1c c2 e0 00 04:41:03.986 READ DMA EXT 25 00 00 00 40 00 2d ae 00 1c ba e0 00 04:41:00.317 READ DMA EXT 25 00 00 00 48 00 2d ae 00 1c b2 e0 00 04:40:56.648 READ DMA EXT 25 00 00 00 50 00 2d ae 00 1c aa e0 00 04:40:52.962 READ DMA EXT 25 00 00 00 58 00 2d ae 00 1c a2 e0 00 04:40:49.276 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 121 - # 2 Extended offline Aborted by host 80% 119 - # 3 Extended offline Aborted by host 80% 119 - # 4 Extended offline Aborted by host 80% 119 - # 5 Extended offline Aborted by host 80% 119 - # 6 Extended offline Aborted by host 80% 118 - # 7 Extended offline Aborted by host 80% 118 - # 8 Extended offline Aborted by host 80% 118 - # 9 Extended offline Aborted by host 80% 118 - #10 Extended offline Aborted by host 80% 117 - #11 Extended offline Aborted by host 80% 117 - #12 Extended offline Aborted by host 80% 117 - #13 Extended offline Aborted by host 80% 117 - #14 Extended offline Aborted by host 80% 116 - #15 Extended offline Aborted by host 80% 116 - #16 Extended offline Aborted by host 80% 116 - #17 Extended offline Aborted by host 80% 116 - #18 Extended offline Aborted by host 80% 115 - #19 Extended offline Aborted by host 80% 115 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read SATA Phy Event Counters failed