/dev/sda,hpsa_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Intel 730 and DC S35x0/3610/3700 Series SSDs Device Model: INTEL SSDSC2BB150G7 Serial Number: 864B90715D82418F5002A7A1EEB98BC4 LU WWN Device Id: 5 5cd2e4 ... Firmware Version: N2010112 User Capacity: 150,039,945,216 bytes [150 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Mar 27 09:57:04 2024 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 34126 12 Power_Cycle_Count -O--CK 100 100 000 - 21 170 Available_Reservd_Space PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 16 175 Power_Loss_Cap_Test PO--CK 100 100 010 - 15630 (223 8) 183 SATA_Downshift_Count -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 090 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 190 Temperature_Case -O---K 076 075 000 - 24 (Min/Max 19/25) 192 Unsafe_Shutdown_Count -O--CK 100 100 000 - 16 194 Temperature_Internal -O---K 100 100 000 - 24 197 Current_Pending_Sector -O--C- 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 225 Host_Writes_32MiB -O--CK 100 100 000 - 2157451 226 Workld_Media_Wear_Indic -O--CK 100 100 000 - 35553 227 Workld_Host_Reads_Perc -O--CK 100 100 000 - 52 228 Workload_Minutes -O--CK 100 100 000 - 2047543 232 Available_Reservd_Space PO--CK 100 100 010 - 0 233 Media_Wearout_Indicator -O--CK 066 066 000 - 0 234 Thermal_Throttle -O--CK 100 100 000 - 0/0 241 Host_Writes_32MiB -O--CK 100 100 000 - 2157451 242 Host_Reads_32MiB -O--CK 100 100 000 - 2357790 243 NAND_Writes_32MiB -O--CK 100 100 000 - 11153838 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 8 Comprehensive SMART error log 0x03 GPL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x98 GPL,SL R/W 16 Host vendor specific log 0x9b-0x9f GPL,SL R/W 16 Host vendor specific log 0xb8 GPL,SL VS 1 Device vendor specific log 0xb9 GPL VS 1704 Device vendor specific log 0xb9 SL VS 168 Device vendor specific log 0xba GPL VS 1280 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 8 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 19/25 Celsius Lifetime Min/Max Temperature: 13/38 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 21 --- Lifetime Power-On Resets 0x01 0x018 6 141390741179 --- Logical Sectors Written 0x01 0x020 6 4244331941 --- Number of Write Commands 0x01 0x028 6 154520187988 --- Logical Sectors Read 0x01 0x030 6 4221920789 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 24 --- Current Temperature 0x05 0x010 1 25 --- Average Short Term Temperature 0x05 0x018 1 24 --- Average Long Term Temperature 0x05 0x020 1 38 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 35 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 34 --- Highest Average Long Term Temperature 0x05 0x048 1 21 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 974 --- Number of Hardware Resets 0x06 0x010 4 116 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 34 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS /dev/sda,hpsa_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: FUJITSU Product: MBE2147RC Revision: 0103 Compliance: SPC-3 User Capacity: 147,086,327,808 bytes [147 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Logical Unit id: 0x500000e117a59a70 Serial number: 77A31D18CDF73F9F9277FF051885FEDE Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Wed Mar 27 09:57:04 2024 UTC SMART support is: Available - device has SMART capability. SMART support is: Disabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 31 C Drive Trip Temperature: 65 C Manufactured in week 12 of year 2011 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 19 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 477436.611 0 write: 0 0 0 0 0 60883.209 0 Non-medium error count: 62 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 40016:08 [2400968 minutes] Number of background scans performed: 1448, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e117a59a72 attached SAS address = 0x500143804016de60 attached phy identifier = 1 Invalid DWORD count = 384 Running disparity error count = 384 Loss of DWORD synchronization = 96 Phy reset problem = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e117a59a73 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 /dev/sda,hpsa_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: P440ar Revision: 7.00 Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sda,hpsa_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_03] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_04] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_05 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_05] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_06 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_07 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_08 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_09 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_10 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_11 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_12 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_13 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_14 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_15 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Intel 730 and DC S35x0/3610/3700 Series SSDs Device Model: INTEL SSDSC2BB150G7 Serial Number: 864B90715D82418F5002A7A1EEB98BC4 LU WWN Device Id: 5 5cd2e4 ... Firmware Version: N2010112 User Capacity: 150,039,945,216 bytes [150 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Mar 27 09:57:04 2024 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 34126 12 Power_Cycle_Count -O--CK 100 100 000 - 21 170 Available_Reservd_Space PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 16 175 Power_Loss_Cap_Test PO--CK 100 100 010 - 15630 (223 8) 183 SATA_Downshift_Count -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 090 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 190 Temperature_Case -O---K 076 075 000 - 24 (Min/Max 19/25) 192 Unsafe_Shutdown_Count -O--CK 100 100 000 - 16 194 Temperature_Internal -O---K 100 100 000 - 24 197 Current_Pending_Sector -O--C- 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 225 Host_Writes_32MiB -O--CK 100 100 000 - 2157451 226 Workld_Media_Wear_Indic -O--CK 100 100 000 - 35553 227 Workld_Host_Reads_Perc -O--CK 100 100 000 - 52 228 Workload_Minutes -O--CK 100 100 000 - 2047543 232 Available_Reservd_Space PO--CK 100 100 010 - 0 233 Media_Wearout_Indicator -O--CK 066 066 000 - 0 234 Thermal_Throttle -O--CK 100 100 000 - 0/0 241 Host_Writes_32MiB -O--CK 100 100 000 - 2157451 242 Host_Reads_32MiB -O--CK 100 100 000 - 2357791 243 NAND_Writes_32MiB -O--CK 100 100 000 - 11153838 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 8 Comprehensive SMART error log 0x03 GPL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x98 GPL,SL R/W 16 Host vendor specific log 0x9b-0x9f GPL,SL R/W 16 Host vendor specific log 0xb8 GPL,SL VS 1 Device vendor specific log 0xb9 GPL VS 1704 Device vendor specific log 0xb9 SL VS 168 Device vendor specific log 0xba GPL VS 1280 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 8 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 19/25 Celsius Lifetime Min/Max Temperature: 13/38 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 21 --- Lifetime Power-On Resets 0x01 0x018 6 141390741179 --- Logical Sectors Written 0x01 0x020 6 4244331941 --- Number of Write Commands 0x01 0x028 6 154520199001 --- Logical Sectors Read 0x01 0x030 6 4221921131 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 24 --- Current Temperature 0x05 0x010 1 25 --- Average Short Term Temperature 0x05 0x018 1 24 --- Average Long Term Temperature 0x05 0x020 1 38 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 35 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 34 --- Highest Average Long Term Temperature 0x05 0x048 1 21 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 974 --- Number of Hardware Resets 0x06 0x010 4 116 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 34 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS /dev/sdb,hpsa_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: FUJITSU Product: MBE2147RC Revision: 0103 Compliance: SPC-3 User Capacity: 147,086,327,808 bytes [147 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Logical Unit id: 0x500000e117a59a70 Serial number: 77A31D18CDF73F9F9277FF051885FEDE Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Wed Mar 27 09:57:04 2024 UTC SMART support is: Available - device has SMART capability. SMART support is: Disabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 31 C Drive Trip Temperature: 65 C Manufactured in week 12 of year 2011 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 19 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 477436.612 0 write: 0 0 0 0 0 60883.209 0 Non-medium error count: 62 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 40016:08 [2400968 minutes] Number of background scans performed: 1448, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e117a59a72 attached SAS address = 0x500143804016de60 attached phy identifier = 1 Invalid DWORD count = 384 Running disparity error count = 384 Loss of DWORD synchronization = 96 Phy reset problem = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e117a59a73 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 /dev/sdb,hpsa_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: P440ar Revision: 7.00 Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sdb,hpsa_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_03] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_04] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_05 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_05] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_06 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_07 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_08 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_09 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_10 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_11 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_12 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_13 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_14 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_15 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Intel 730 and DC S35x0/3610/3700 Series SSDs Device Model: INTEL SSDSC2BB150G7 Serial Number: 864B90715D82418F5002A7A1EEB98BC4 LU WWN Device Id: 5 5cd2e4 ... Firmware Version: N2010112 User Capacity: 150,039,945,216 bytes [150 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Mar 27 09:57:05 2024 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 34126 12 Power_Cycle_Count -O--CK 100 100 000 - 21 170 Available_Reservd_Space PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 16 175 Power_Loss_Cap_Test PO--CK 100 100 010 - 15630 (223 8) 183 SATA_Downshift_Count -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 090 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 190 Temperature_Case -O---K 076 075 000 - 24 (Min/Max 19/25) 192 Unsafe_Shutdown_Count -O--CK 100 100 000 - 16 194 Temperature_Internal -O---K 100 100 000 - 24 197 Current_Pending_Sector -O--C- 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 225 Host_Writes_32MiB -O--CK 100 100 000 - 2157451 226 Workld_Media_Wear_Indic -O--CK 100 100 000 - 35553 227 Workld_Host_Reads_Perc -O--CK 100 100 000 - 52 228 Workload_Minutes -O--CK 100 100 000 - 2047543 232 Available_Reservd_Space PO--CK 100 100 010 - 0 233 Media_Wearout_Indicator -O--CK 066 066 000 - 0 234 Thermal_Throttle -O--CK 100 100 000 - 0/0 241 Host_Writes_32MiB -O--CK 100 100 000 - 2157451 242 Host_Reads_32MiB -O--CK 100 100 000 - 2357791 243 NAND_Writes_32MiB -O--CK 100 100 000 - 11153838 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 8 Comprehensive SMART error log 0x03 GPL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x98 GPL,SL R/W 16 Host vendor specific log 0x9b-0x9f GPL,SL R/W 16 Host vendor specific log 0xb8 GPL,SL VS 1 Device vendor specific log 0xb9 GPL VS 1704 Device vendor specific log 0xb9 SL VS 168 Device vendor specific log 0xba GPL VS 1280 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 8 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 19/25 Celsius Lifetime Min/Max Temperature: 13/38 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 21 --- Lifetime Power-On Resets 0x01 0x018 6 141390741179 --- Logical Sectors Written 0x01 0x020 6 4244331941 --- Number of Write Commands 0x01 0x028 6 154520234511 --- Logical Sectors Read 0x01 0x030 6 4221922111 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 24 --- Current Temperature 0x05 0x010 1 25 --- Average Short Term Temperature 0x05 0x018 1 24 --- Average Long Term Temperature 0x05 0x020 1 38 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 35 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 34 --- Highest Average Long Term Temperature 0x05 0x048 1 21 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 974 --- Number of Hardware Resets 0x06 0x010 4 116 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 34 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS /dev/sg0,hpsa_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: FUJITSU Product: MBE2147RC Revision: 0103 Compliance: SPC-3 User Capacity: 147,086,327,808 bytes [147 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Logical Unit id: 0x500000e117a59a70 Serial number: 77A31D18CDF73F9F9277FF051885FEDE Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Wed Mar 27 09:57:05 2024 UTC SMART support is: Available - device has SMART capability. SMART support is: Disabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 31 C Drive Trip Temperature: 65 C Manufactured in week 12 of year 2011 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 19 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 477436.622 0 write: 0 0 0 0 0 60883.209 0 Non-medium error count: 62 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 40016:08 [2400968 minutes] Number of background scans performed: 1448, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e117a59a72 attached SAS address = 0x500143804016de60 attached phy identifier = 1 Invalid DWORD count = 384 Running disparity error count = 384 Loss of DWORD synchronization = 96 Phy reset problem = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e117a59a73 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 /dev/sg0,hpsa_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: P440ar Revision: 7.00 Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sg0,hpsa_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_03] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_04] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_05 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_05] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_06 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_07 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_08 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_09 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_10 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_11 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_12 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_13 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_14 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_15 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address