/dev/sda,hpsa_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7KM960HAHP-00005 Serial Number: B7142C77DABECB8C8EAA6DA08B487D7A LU WWN Device Id: 5 002538 ... Firmware Version: GXM1103Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Apr 7 19:12:12 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 091 091 000 - 43634 12 Power_Cycle_Count -O--CK 099 099 000 - 34 177 Wear_Leveling_Count PO--C- 099 099 005 - 195 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 7692 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 070 057 000 - 30 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 31 241 Total_LBAs_Written -O--CK 099 099 000 - 277940896523 242 Total_LBAs_Read -O--CK 099 099 000 - 161207034727 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 376292026408 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 28/30 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 538451970/268435472 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7KM960HAHP-00005 Serial Number: B7142C77DABECB8C8EAA6DA08B487D7A LU WWN Device Id: 5 002538 ... Firmware Version: GXM1103Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Apr 7 19:12:12 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 091 091 000 - 43634 12 Power_Cycle_Count -O--CK 099 099 000 - 34 177 Wear_Leveling_Count PO--C- 099 099 005 - 195 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 7692 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 070 057 000 - 30 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 31 241 Total_LBAs_Written -O--CK 099 099 000 - 277940896523 242 Total_LBAs_Read -O--CK 099 099 000 - 161207036808 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 376292026408 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 28/30 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 538451970/268435472 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7KM960HAHP-00005 Serial Number: C3DDA2EB2EA0036A8FB68C035F34B2B7 LU WWN Device Id: 5 002538 ... Firmware Version: GXM1103Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Apr 7 19:12:12 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 091 091 000 - 43635 12 Power_Cycle_Count -O--CK 099 099 000 - 34 177 Wear_Leveling_Count PO--C- 099 099 005 - 181 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 7719 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 069 057 000 - 31 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 31 241 Total_LBAs_Written -O--CK 099 099 000 - 253267230409 242 Total_LBAs_Read -O--CK 099 099 000 - 161011179285 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 345039820176 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 30/31 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 0/16386 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_02 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7KM960HAHP-00005 Serial Number: F738BED79EFB712F207433FFF5EB2585 LU WWN Device Id: 5 002538 ... Firmware Version: GXM1103Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Apr 7 19:12:12 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 091 091 000 - 43661 12 Power_Cycle_Count -O--CK 099 099 000 - 46 177 Wear_Leveling_Count PO--C- 099 099 005 - 202 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 7726 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 069 057 000 - 31 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 43 241 Total_LBAs_Written -O--CK 099 099 000 - 287483391907 242 Total_LBAs_Read -O--CK 099 099 000 - 228665531453 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 389855492360 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 29/31 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 4294967295/4294967295 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG MZ7KM960HAHP-00005 Serial Number: 013A7E48607F434779FC6D84A0F5829E LU WWN Device Id: 5 002538 ... Firmware Version: GXM1103Q User Capacity: 960,197,124,096 bytes [960 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Apr 7 19:12:12 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Operation not supported Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3600) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 091 091 000 - 43661 12 Power_Cycle_Count -O--CK 099 099 000 - 45 177 Wear_Leveling_Count PO--C- 099 099 005 - 182 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 7710 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 070 058 000 - 30 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 202 Exception_Mode_Status PO--CK 100 100 010 - 0 235 POR_Recovery_Count -O--C- 099 099 000 - 42 241 Total_LBAs_Written -O--CK 099 099 000 - 255513672712 242 Total_LBAs_Read -O--CK 099 099 000 - 158897626093 243 SATA_Downshift_Ct -O--CK 100 100 000 - 0 244 Thermal_Throttle_St -O--CK 100 100 000 - 0 245 Timed_Workld_Media_Wear -O--CK 100 100 000 - 65535 246 Timed_Workld_RdWr_Ratio -O--CK 100 100 000 - 65535 247 Timed_Workld_Timer -O--CK 100 100 000 - 65535 251 NAND_Writes -O--CK 100 100 000 - 347602509832 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was completed without error Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 28/30 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 0/536870976 Write SCT Data Table failed: Operation not supported Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: Operation not supported SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sg0,hpsa_disk_04 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: P440ar Revision: 7.20 Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sg0,hpsa_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_05] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_06 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_07 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_08 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_09 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_10 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_11 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_12 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_13 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_14 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_15 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address