/dev/sda,hpsa_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MM2000JEFRC Revision: HPD7 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Rotation Rate: 7200 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5009e74ac6b Serial number: 4C12B824BBCD2F255B6A741ED469CC54 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon May 9 13:47:29 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 52 of year 2016 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 80 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1752 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 92774.720 0 write: 0 0 0 0 0 73928.656 0 Non-medium error count: 20374 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 40867:21 [2452041 minutes] Number of background scans performed: 284, scan progress: 54.73% Number of background medium scans performed: 284 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e74ac69 attached SAS address = 0x500143802942d080 attached phy identifier = 0 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization = 587 Phy reset problem = 18 Phy event descriptors: Invalid word count: 4 Running disparity error count: 4 Loss of dword synchronization count: 587 Phy reset problem count: 18 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e74ac6a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,hpsa_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MM2000JEFRC Revision: HPD7 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Rotation Rate: 7200 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5009912a9d3 Serial number: 1A07F2E8A6A35BDA43159D8B224E1588 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon May 9 13:47:30 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 08 of year 2017 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 59 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1581 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 52447.746 0 write: 0 0 0 0 0 90770.549 0 verify: 0 0 0 0 0 0.000 0 Non-medium error count: 20655 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 36689:38 [2201378 minutes] Number of background scans performed: 257, scan progress: 54.32% Number of background medium scans performed: 257 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009912a9d1 attached SAS address = 0x500143802942d080 attached phy identifier = 1 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 164 Phy reset problem = 19 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 164 Phy reset problem count: 19 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009912a9d2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,hpsa_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MM2000JEFRC Revision: HPD7 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Rotation Rate: 7200 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5009e74e3b3 Serial number: 88AC4FD5E98A0D1C9E6413FF703201C0 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon May 9 13:47:31 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 37 C Drive Trip Temperature: 60 C Manufactured in week 52 of year 2016 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 80 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1752 Elements in grown defect list: 48 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 94612.871 0 write: 0 0 0 51 0 88989.310 1 Non-medium error count: 20628 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 40867:49 [2452069 minutes] Number of background scans performed: 284, scan progress: 54.49% Number of background medium scans performed: 284 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e74e3b1 attached SAS address = 0x500143802942d080 attached phy identifier = 2 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 583 Phy reset problem = 18 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 583 Phy reset problem count: 18 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e74e3b2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,hpsa_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MM2000JEFRC Revision: HPD7 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Rotation Rate: 7200 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5009ebd0693 Serial number: 056BB40C3E7447FCCB635ED3D9430922 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon May 9 13:47:32 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 37 C Drive Trip Temperature: 60 C Manufactured in week 10 of year 2017 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 72 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1708 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 180799.189 0 write: 0 0 0 0 0 86699.981 0 Non-medium error count: 20340 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 39444:58 [2366698 minutes] Number of background scans performed: 276, scan progress: 54.27% Number of background medium scans performed: 276 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009ebd0691 attached SAS address = 0x500143802942d080 attached phy identifier = 3 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 118 Phy reset problem = 19 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 118 Phy reset problem count: 19 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009ebd0692 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,hpsa_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MM2000JEFRC Revision: HPD6 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Rotation Rate: 7200 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5009e7501c3 Serial number: 227D9A66AC5475ED54E982B5D0EEACE0 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon May 9 13:47:33 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 34 C Drive Trip Temperature: 60 C Manufactured in week 52 of year 2016 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 73 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1780 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 168001.153 0 write: 0 0 0 0 0 87922.320 0 Non-medium error count: 20428 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 41167:46 [2470066 minutes] Number of background scans performed: 288, scan progress: 54.28% Number of background medium scans performed: 288 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e7501c1 attached SAS address = 0x500143802942d084 attached phy identifier = 4 Invalid DWORD count = 4 Running disparity error count = 3 Loss of DWORD synchronization = 132 Phy reset problem = 18 Phy event descriptors: Invalid word count: 4 Running disparity error count: 3 Loss of dword synchronization count: 132 Phy reset problem count: 18 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e7501c2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,hpsa_disk_05 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: PMCSIERA Product: SRCv8x6G Revision: RevB Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sda,hpsa_disk_06 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_07 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_08 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_09 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_10 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_11 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_12 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_13 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_14 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_15 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg1,hpsa_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MM2000JEFRC Revision: HPD7 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Rotation Rate: 7200 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5009e74ac6b Serial number: 4C12B824BBCD2F255B6A741ED469CC54 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon May 9 13:47:34 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 52 of year 2016 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 80 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1752 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 92774.746 0 write: 0 0 0 0 0 73928.657 0 Non-medium error count: 20375 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 40867:21 [2452041 minutes] Number of background scans performed: 284, scan progress: 54.73% Number of background medium scans performed: 284 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e74ac69 attached SAS address = 0x500143802942d080 attached phy identifier = 0 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization = 587 Phy reset problem = 18 Phy event descriptors: Invalid word count: 4 Running disparity error count: 4 Loss of dword synchronization count: 587 Phy reset problem count: 18 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e74ac6a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sg1,hpsa_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MM2000JEFRC Revision: HPD7 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Rotation Rate: 7200 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5009912a9d3 Serial number: 1A07F2E8A6A35BDA43159D8B224E1588 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon May 9 13:47:35 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 08 of year 2017 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 59 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1581 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 52447.757 0 write: 0 0 0 0 0 90770.551 0 verify: 0 0 0 0 0 0.000 0 Non-medium error count: 20656 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 36689:38 [2201378 minutes] Number of background scans performed: 257, scan progress: 54.32% Number of background medium scans performed: 257 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009912a9d1 attached SAS address = 0x500143802942d080 attached phy identifier = 1 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 164 Phy reset problem = 19 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 164 Phy reset problem count: 19 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009912a9d2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sg1,hpsa_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MM2000JEFRC Revision: HPD7 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Rotation Rate: 7200 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5009e74e3b3 Serial number: 88AC4FD5E98A0D1C9E6413FF703201C0 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon May 9 13:47:36 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 37 C Drive Trip Temperature: 60 C Manufactured in week 52 of year 2016 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 80 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1752 Elements in grown defect list: 48 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 94612.884 0 write: 0 0 0 51 0 88989.310 1 Non-medium error count: 20629 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 40867:49 [2452069 minutes] Number of background scans performed: 284, scan progress: 54.49% Number of background medium scans performed: 284 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e74e3b1 attached SAS address = 0x500143802942d080 attached phy identifier = 2 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 583 Phy reset problem = 18 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 583 Phy reset problem count: 18 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e74e3b2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sg1,hpsa_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MM2000JEFRC Revision: HPD7 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Rotation Rate: 7200 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5009ebd0693 Serial number: 056BB40C3E7447FCCB635ED3D9430922 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon May 9 13:47:37 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 37 C Drive Trip Temperature: 60 C Manufactured in week 10 of year 2017 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 72 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1708 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 180799.199 0 write: 0 0 0 0 0 86699.982 0 Non-medium error count: 20341 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 39444:58 [2366698 minutes] Number of background scans performed: 276, scan progress: 54.28% Number of background medium scans performed: 276 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009ebd0691 attached SAS address = 0x500143802942d080 attached phy identifier = 3 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 118 Phy reset problem = 19 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 118 Phy reset problem count: 19 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009ebd0692 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sg1,hpsa_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MM2000JEFRC Revision: HPD6 Compliance: SPC-4 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes Rotation Rate: 7200 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5009e7501c3 Serial number: 227D9A66AC5475ED54E982B5D0EEACE0 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon May 9 13:47:38 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 34 C Drive Trip Temperature: 60 C Manufactured in week 52 of year 2016 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 73 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1780 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 168001.161 0 write: 0 0 0 0 0 87922.320 0 Non-medium error count: 20429 No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 41167:46 [2470066 minutes] Number of background scans performed: 288, scan progress: 54.29% Number of background medium scans performed: 288 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: hard reset negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e7501c1 attached SAS address = 0x500143802942d084 attached phy identifier = 4 Invalid DWORD count = 4 Running disparity error count = 3 Loss of DWORD synchronization = 132 Phy reset problem = 18 Phy event descriptors: Invalid word count: 4 Running disparity error count: 3 Loss of dword synchronization count: 132 Phy reset problem count: 18 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5009e7501c2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sg1,hpsa_disk_05 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: PMCSIERA Product: SRCv8x6G Revision: RevB Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sg1,hpsa_disk_06 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg1 [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg1,hpsa_disk_07 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg1 [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg1,hpsa_disk_08 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg1 [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg1,hpsa_disk_09 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg1 [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg1,hpsa_disk_10 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg1 [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg1,hpsa_disk_11 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg1 [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg1,hpsa_disk_12 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg1 [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg1,hpsa_disk_13 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg1 [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg1,hpsa_disk_14 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg1 [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg1,hpsa_disk_15 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-27-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg1 [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address