/dev/sda,hpsa_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MO0200JEFNV Revision: HPD3 Compliance: SPC-4 User Capacity: 200,049,647,616 bytes [200 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5000cca04da9bc48 Serial number: 6A928787C240C721C5F88E828E534E39 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Fri Sep 29 13:38:50 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 5% Current Drive Temperature: 26 C Drive Trip Temperature: 60 C Manufactured in week 49 of year 2015 Specified cycle count over device lifetime: 0 Accumulated start-stop cycles: 0 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 27525.258 0 write: 0 0 0 0 0 256760.026 0 verify: 0 0 0 0 0 0.000 0 Non-medium error count: 2783 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Aborted (by user command) 6 41185 - [- - -] # 2 Background short Aborted (by user command) 5 41185 - [- - -] # 3 Background short Aborted (by user command) 3 41185 - [- - -] # 4 Background short Aborted (by user command) 6 41185 - [- - -] # 5 Background short Aborted (by user command) 6 41185 - [- - -] # 6 Background short Aborted (by user command) 3 41185 - [- - -] # 7 Background long Aborted (by user command) 7 41185 - [- - -] # 8 Background long Aborted (by user command) 7 41185 - [- - -] # 9 Background short Aborted (by user command) 5 41185 - [- - -] #10 Background short Aborted (by user command) 4 41185 - [- - -] #11 Background short Aborted (by user command) 6 41185 - [- - -] #12 Background short Aborted (by user command) 5 41185 - [- - -] #13 Background long Aborted (by user command) 7 41185 - [- - -] #14 Background long Aborted (by user command) 7 41185 - [- - -] #15 Background short Aborted (by user command) 6 41184 - [- - -] #16 Background short Aborted (by user command) 4 41184 - [- - -] #17 Background short Aborted (by user command) 6 41184 - [- - -] #18 Background short Aborted (by user command) 5 41184 - [- - -] #19 Background short Aborted (by user command) 6 41183 - [- - -] #20 Background short Aborted (by user command) 4 41183 - [- - -] Long (extended) Self-test duration: 1398 seconds [23.3 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 48844:34 [2930674 minutes] Number of background scans performed: 1928, scan progress: 0.00% Number of background medium scans performed: 1928 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04da9bc49 attached SAS address = 0x50014380361c9150 attached phy identifier = 0 Invalid DWORD count = 53 Running disparity error count = 27 Loss of DWORD synchronization = 11 Phy reset problem = 0 Phy event descriptors: Invalid word count: 53 Running disparity error count: 27 Loss of dword synchronization count: 11 Phy reset problem count: 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04da9bc4a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sda,hpsa_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: FUJITSU Product: MBE2147RC Revision: 0103 Compliance: SPC-3 User Capacity: 147,086,327,808 bytes [147 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Logical Unit id: 0x500000e118012cb0 Serial number: 205225CFF2C206DF4789DCA6A7890481 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Fri Sep 29 13:38:50 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Disabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 29 C Drive Trip Temperature: 65 C Manufactured in week 24 of year 2011 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 19 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 1011644.755 0 write: 0 0 0 0 0 197195.491 0 Non-medium error count: 142 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 97383:34 [5843014 minutes] Number of background scans performed: 4051, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e118012cb2 attached SAS address = 0x50014380361c9150 attached phy identifier = 1 Invalid DWORD count = 981 Running disparity error count = 977 Loss of DWORD synchronization = 243 Phy reset problem = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e118012cb3 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 /dev/sda,hpsa_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: P440ar Revision: 7.00 Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sda,hpsa_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_03] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_04] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_05 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_05] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_06 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_07 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_08 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_09 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_10 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_11 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_12 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_13 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_14 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_15 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MO0200JEFNV Revision: HPD3 Compliance: SPC-4 User Capacity: 200,049,647,616 bytes [200 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5000cca04da9bc48 Serial number: 6A928787C240C721C5F88E828E534E39 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Fri Sep 29 13:38:51 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 5% Current Drive Temperature: 26 C Drive Trip Temperature: 60 C Manufactured in week 49 of year 2015 Specified cycle count over device lifetime: 0 Accumulated start-stop cycles: 0 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 27525.263 0 write: 0 0 0 0 0 256760.026 0 verify: 0 0 0 0 0 0.000 0 Non-medium error count: 2783 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Aborted (by user command) 6 41185 - [- - -] # 2 Background short Aborted (by user command) 5 41185 - [- - -] # 3 Background short Aborted (by user command) 3 41185 - [- - -] # 4 Background short Aborted (by user command) 6 41185 - [- - -] # 5 Background short Aborted (by user command) 6 41185 - [- - -] # 6 Background short Aborted (by user command) 3 41185 - [- - -] # 7 Background long Aborted (by user command) 7 41185 - [- - -] # 8 Background long Aborted (by user command) 7 41185 - [- - -] # 9 Background short Aborted (by user command) 5 41185 - [- - -] #10 Background short Aborted (by user command) 4 41185 - [- - -] #11 Background short Aborted (by user command) 6 41185 - [- - -] #12 Background short Aborted (by user command) 5 41185 - [- - -] #13 Background long Aborted (by user command) 7 41185 - [- - -] #14 Background long Aborted (by user command) 7 41185 - [- - -] #15 Background short Aborted (by user command) 6 41184 - [- - -] #16 Background short Aborted (by user command) 4 41184 - [- - -] #17 Background short Aborted (by user command) 6 41184 - [- - -] #18 Background short Aborted (by user command) 5 41184 - [- - -] #19 Background short Aborted (by user command) 6 41183 - [- - -] #20 Background short Aborted (by user command) 4 41183 - [- - -] Long (extended) Self-test duration: 1398 seconds [23.3 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 48844:34 [2930674 minutes] Number of background scans performed: 1928, scan progress: 0.00% Number of background medium scans performed: 1928 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04da9bc49 attached SAS address = 0x50014380361c9150 attached phy identifier = 0 Invalid DWORD count = 53 Running disparity error count = 27 Loss of DWORD synchronization = 11 Phy reset problem = 0 Phy event descriptors: Invalid word count: 53 Running disparity error count: 27 Loss of dword synchronization count: 11 Phy reset problem count: 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04da9bc4a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sdb,hpsa_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: FUJITSU Product: MBE2147RC Revision: 0103 Compliance: SPC-3 User Capacity: 147,086,327,808 bytes [147 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Logical Unit id: 0x500000e118012cb0 Serial number: 205225CFF2C206DF4789DCA6A7890481 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Fri Sep 29 13:38:51 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Disabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 29 C Drive Trip Temperature: 65 C Manufactured in week 24 of year 2011 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 19 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 1011644.755 0 write: 0 0 0 0 0 197195.491 0 Non-medium error count: 142 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 97383:34 [5843014 minutes] Number of background scans performed: 4051, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e118012cb2 attached SAS address = 0x50014380361c9150 attached phy identifier = 1 Invalid DWORD count = 981 Running disparity error count = 977 Loss of DWORD synchronization = 243 Phy reset problem = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e118012cb3 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 /dev/sdb,hpsa_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: P440ar Revision: 7.00 Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sdb,hpsa_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_03] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_04] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_05 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_05] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_06 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_07 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_08 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_09 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_10 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_11 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_12 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_13 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_14 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sdb,hpsa_disk_15 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sdb [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: MO0200JEFNV Revision: HPD3 Compliance: SPC-4 User Capacity: 200,049,647,616 bytes [200 GB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is resource provisioned, LBPRZ=1 Rotation Rate: Solid State Device Form Factor: 2.5 inches Logical Unit id: 0x5000cca04da9bc48 Serial number: 6A928787C240C721C5F88E828E534E39 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Fri Sep 29 13:38:51 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Percentage used endurance indicator: 5% Current Drive Temperature: 26 C Drive Trip Temperature: 60 C Manufactured in week 49 of year 2015 Specified cycle count over device lifetime: 0 Accumulated start-stop cycles: 0 Specified load-unload count over device lifetime: 0 Accumulated load-unload cycles: 0 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 27525.280 0 write: 0 0 0 0 0 256760.026 0 verify: 0 0 0 0 0 0.000 0 Non-medium error count: 2783 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Aborted (by user command) 6 41185 - [- - -] # 2 Background short Aborted (by user command) 5 41185 - [- - -] # 3 Background short Aborted (by user command) 3 41185 - [- - -] # 4 Background short Aborted (by user command) 6 41185 - [- - -] # 5 Background short Aborted (by user command) 6 41185 - [- - -] # 6 Background short Aborted (by user command) 3 41185 - [- - -] # 7 Background long Aborted (by user command) 7 41185 - [- - -] # 8 Background long Aborted (by user command) 7 41185 - [- - -] # 9 Background short Aborted (by user command) 5 41185 - [- - -] #10 Background short Aborted (by user command) 4 41185 - [- - -] #11 Background short Aborted (by user command) 6 41185 - [- - -] #12 Background short Aborted (by user command) 5 41185 - [- - -] #13 Background long Aborted (by user command) 7 41185 - [- - -] #14 Background long Aborted (by user command) 7 41185 - [- - -] #15 Background short Aborted (by user command) 6 41184 - [- - -] #16 Background short Aborted (by user command) 4 41184 - [- - -] #17 Background short Aborted (by user command) 6 41184 - [- - -] #18 Background short Aborted (by user command) 5 41184 - [- - -] #19 Background short Aborted (by user command) 6 41183 - [- - -] #20 Background short Aborted (by user command) 4 41183 - [- - -] Long (extended) Self-test duration: 1398 seconds [23.3 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 48844:34 [2930674 minutes] Number of background scans performed: 1928, scan progress: 0.00% Number of background medium scans performed: 1928 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 3 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04da9bc49 attached SAS address = 0x50014380361c9150 attached phy identifier = 0 Invalid DWORD count = 53 Running disparity error count = 27 Loss of DWORD synchronization = 11 Phy reset problem = 0 Phy event descriptors: Invalid word count: 53 Running disparity error count: 27 Loss of dword synchronization count: 11 Phy reset problem count: 0 relative target port id = 2 generation code = 3 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: power on negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000cca04da9bc4a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sg0,hpsa_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: FUJITSU Product: MBE2147RC Revision: 0103 Compliance: SPC-3 User Capacity: 147,086,327,808 bytes [147 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Logical Unit id: 0x500000e118012cb0 Serial number: 205225CFF2C206DF4789DCA6A7890481 Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Fri Sep 29 13:38:51 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Disabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 29 C Drive Trip Temperature: 65 C Manufactured in week 24 of year 2011 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 19 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 1011644.763 0 write: 0 0 0 0 0 197195.491 0 Non-medium error count: 142 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 97383:34 [5843014 minutes] Number of background scans performed: 4051, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e118012cb2 attached SAS address = 0x50014380361c9150 attached phy identifier = 1 Invalid DWORD count = 981 Running disparity error count = 977 Loss of DWORD synchronization = 243 Phy reset problem = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e118012cb3 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 /dev/sg0,hpsa_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: P440ar Revision: 7.00 Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sg0,hpsa_disk_03 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_03] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_04 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_04] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_05 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_05] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_06 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_07 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_08 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_09 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_10 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_11 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_12 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_13 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_14 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_15 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-69-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address