/dev/sde,megaraid_disk_05 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.11.2-zen1-1-zen] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST900MM0026 Revision: 0001 Compliance: SPC-4 User Capacity: 900,185,481,216 bytes [900 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10500 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c50056690787 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Wed Mar 3 14:24:55 2021 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 33 C Drive Trip Temperature: 68 C Manufactured in week of year 20 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 369 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 2262 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 21505 Blocks received from initiator = 2 Blocks read from cache and sent to initiator = 2936 Number of read and write commands whose size <= segment size = 26 Number of read and write commands whose size > segment size = 0 Vendor (Seagate/Hitachi) factory information number of hours powered up = 38462.25 number of minutes until next internal SMART test = 52 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 41334 0 0 41334 0 0.011 0 write: 0 0 0 0 0 1.401 0 Non-medium error count: 0 [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 38462:15 [2307735 minutes] Number of background scans performed: 452, scan progress: 0.00% Number of background medium scans performed: 452 # when lba(hex) [sk,asc,ascq] reassign_status 1 26790:34 000000005aa11cf2 [1,17,1] Recovered via rewrite in-place 2 29157:28 000000005aa11cf2 [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: power on negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50056690785 attached SAS address = 0x5003048013dca500 attached phy identifier = 4 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50056690786 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sde,megaraid_disk_06 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.11.2-zen1-1-zen] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST900MM0026 Revision: 0001 Compliance: SPC-4 User Capacity: 900,185,481,216 bytes [900 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10500 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c5005f6a25a3 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Wed Mar 3 14:24:59 2021 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 32 C Drive Trip Temperature: 68 C Manufactured in week of year 20 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 369 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 3055 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 18577 Blocks received from initiator = 0 Blocks read from cache and sent to initiator = 1056 Number of read and write commands whose size <= segment size = 19 Number of read and write commands whose size > segment size = 0 Vendor (Seagate/Hitachi) factory information number of hours powered up = 38462.83 number of minutes until next internal SMART test = 52 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 30641 0 0 30641 0 0.010 0 write: 0 0 0 0 0 1.401 0 Non-medium error count: 0 [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 38462:50 [2307770 minutes] Number of background scans performed: 452, scan progress: 0.00% Number of background medium scans performed: 452 # when lba(hex) [sk,asc,ascq] reassign_status 1 3802:31 00000000082c8962 [1,17,1] Recovered via rewrite in-place 2 15508:05 0000000002d2137c [1,17,1] Recovered via rewrite in-place 3 16084:01 000000000346061d [1,17,1] Recovered via rewrite in-place 4 16299:58 0000000002d2137d [1,17,1] Recovered via rewrite in-place 5 17019:53 000000000346061e [1,17,1] Recovered via rewrite in-place 6 17451:21 000000000346061c [1,17,1] Recovered via rewrite in-place 7 18099:13 0000000003460620 [1,17,1] Recovered via rewrite in-place 8 18963:03 000000000346061b [1,17,1] Recovered via rewrite in-place 9 36995:46 0000000000001abb [1,17,1] Recovered via rewrite in-place 10 37118:57 0000000000002cb6 [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5005f6a25a1 attached SAS address = 0x5003048013dca501 attached phy identifier = 5 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5005f6a25a2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sde,megaraid_disk_08 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.11.2-zen1-1-zen] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST3000NM0023 Revision: 0004 Compliance: SPC-4 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5006321cc6b Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Wed Mar 3 14:25:02 2021 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 52 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 378 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1498 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 3238932927 Blocks received from initiator = 48344135 Blocks read from cache and sent to initiator = 4282646763 Number of read and write commands whose size <= segment size = 2167041450 Number of read and write commands whose size > segment size = 36677 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36550.77 number of minutes until next internal SMART test = 52 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 4148218798 0 0 4148218798 0 36842.706 0 write: 0 0 0 0 0 344997.332 0 verify: 5405 0 0 5405 0 0.000 0 Non-medium error count: 22 [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 36550:46 [2193046 minutes] Number of background scans performed: 89, scan progress: 88.53% Number of background medium scans performed: 89 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5006321cc69 attached SAS address = 0x5003048013dca503 attached phy identifier = 7 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5006321cc6a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0 /dev/sde,megaraid_disk_09 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.11.2-zen1-1-zen] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST3000NM0023 Revision: 0004 Compliance: SPC-4 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500632102e7 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Wed Mar 3 14:25:03 2021 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 38 C Drive Trip Temperature: 60 C Manufactured in week 52 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 376 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 1574 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 3400633506 Blocks received from initiator = 2517481172 Blocks read from cache and sent to initiator = 1718124003 Number of read and write commands whose size <= segment size = 2642217719 Number of read and write commands whose size > segment size = 107212 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36546.72 number of minutes until next internal SMART test = 52 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 3405461738 0 0 3405461738 0 175463.962 0 write: 0 0 0 0 0 416807.508 0 verify: 10324 0 0 10324 0 0.000 0 Non-medium error count: 57 [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: scan is active Accumulated power on time, hours:minutes 36546:43 [2192803 minutes] Number of background scans performed: 278, scan progress: 89.24% Number of background medium scans performed: 278 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500632102e5 attached SAS address = 0x5003048013dca502 attached phy identifier = 6 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 1 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 1 Phy reset problem count: 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500632102e6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 Phy event descriptors: Invalid word count: 0 Running disparity error count: 0 Loss of dword synchronization count: 0 Phy reset problem count: 0