/dev/sda,megaraid_disk_00 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.19.0-38-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: FUJITSU Product: MBE2147RC Revision: 0103 Compliance: SPC-3 User Capacity: 147,086,327,808 bytes [147 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Logical Unit id: 0x500000e114a00430 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon Oct 2 09:54:53 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 22 C Drive Trip Temperature: 65 C Manufactured in week 15 of year 2010 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 36 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 829039.647 0 write: 0 0 0 0 0 28611.419 0 verify: 0 0 0 0 0 86045.519 0 Non-medium error count: 38 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 116080:12 [6964812 minutes] Number of background scans performed: 4836, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e114a00432 attached SAS address = 0x5782bcb06ec35802 attached phy identifier = 7 Invalid DWORD count = 676 Running disparity error count = 674 Loss of DWORD synchronization = 169 Phy reset problem = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e114a00433 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 /dev/sda,megaraid_disk_01 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.19.0-38-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: FUJITSU Product: MBE2147RC Revision: 0103 Compliance: SPC-3 User Capacity: 147,086,327,808 bytes [147 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Logical Unit id: 0x500000e11832d8a0 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon Oct 2 09:54:53 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 24 C Drive Trip Temperature: 65 C Manufactured in week 32 of year 2011 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 29 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 607652.870 0 write: 0 0 0 0 0 10369.110 0 verify: 0 0 0 0 0 71042.706 0 Non-medium error count: 28 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 85749:44 [5144984 minutes] Number of background scans performed: 3572, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e11832d8a2 attached SAS address = 0x5782bcb06ec35801 attached phy identifier = 6 Invalid DWORD count = 368 Running disparity error count = 368 Loss of DWORD synchronization = 92 Phy reset problem = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e11832d8a3 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0 /dev/sda,megaraid_disk_02 smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.19.0-38-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: FUJITSU Product: MBE2147RC Revision: 0103 Compliance: SPC-3 User Capacity: 147,086,327,808 bytes [147 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Logical Unit id: 0x500000e1120c5300 Serial number: -- Device type: disk Transport protocol: SAS (SPL-3) Local Time is: Mon Oct 2 09:54:53 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Enabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 23 C Drive Trip Temperature: 65 C Manufactured in week 39 of year 2009 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 29 Elements in grown defect list: 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 13 0 0 0 686535.056 0 write: 0 0 0 0 0 31423.084 0 verify: 0 0 0 0 0 67512.637 0 Non-medium error count: 27 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 95975:41 [5758541 minutes] Number of background scans performed: 3998, scan progress: 0.00% Number of background medium scans performed: 0 # when lba(hex) [sk,asc,ascq] reassign_status 1 45139:25 000000000e81f3f5 [1,18,7] Recovered via rewrite in-place 2 61723:28 000000000e81f725 [1,18,7] Recovered via rewrite in-place 3 76843:30 000000000e88e8a3 [1,18,7] Recovered via rewrite in-place 4 85915:30 000000000eecb901 [1,18,7] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: power on reason: power on negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e1120c5302 attached SAS address = 0x5782bcb06ec35800 attached phy identifier = 5 Invalid DWORD count = 248 Running disparity error count = 248 Loss of DWORD synchronization = 62 Phy reset problem = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x500000e1120c5303 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization = 0 Phy reset problem = 0