/dev/sda,megaraid_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG SSD SM841 2.5" 7mm 256GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: DXM02D0Q User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 26 11:28:14 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12480) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 20) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 176 175 Program_Fail_Count_Chip -O--CK 100 100 010 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 010 - 0 177 Wear_Leveling_Count PO--C- 058 058 005 - 1522 178 Used_Rsvd_Blk_Cnt_Chip PO--C- 100 100 010 - 0 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 9152 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 241 Total_LBAs_Written -O--CK 099 099 000 - 94792794075 242 Total_LBAs_Read -O--CK 099 099 000 - 20428142992 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 1 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 16 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 23/40 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 11 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 11 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sda,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG SSD SM841 2.5" 7mm 256GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: DXM02D0Q User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 26 11:28:14 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12480) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 20) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 173 175 Program_Fail_Count_Chip -O--CK 100 100 010 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 010 - 0 177 Wear_Leveling_Count PO--C- 086 086 005 - 494 178 Used_Rsvd_Blk_Cnt_Chip PO--C- 100 100 010 - 0 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 9152 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 241 Total_LBAs_Written -O--CK 099 099 000 - 45201110189 242 Total_LBAs_Read -O--CK 099 099 000 - 18434373821 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 1 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 16 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 22/40 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sda,megaraid_disk_02 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST300MM0006 Revision: LS0A Compliance: SPC-4 User Capacity: 300,000,000,000 bytes [300 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c50063274bbb Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Feb 26 11:28:14 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 50 C Manufactured in week 52 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 82 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 2386 Elements in grown defect list: 1 Vendor (Seagate Cache) information Blocks sent to initiator = 3407263905 Blocks received from initiator = 92558027 Blocks read from cache and sent to initiator = 810021941 Number of read and write commands whose size <= segment size = 503650710 Number of read and write commands whose size > segment size = 97 Vendor (Seagate/Hitachi) factory information number of hours powered up = 55410.20 number of minutes until next internal SMART test = 51 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 761342644 0 0 761342644 0 4913.463 0 write: 0 0 12 12 13 30553.595 1 verify: 2125799863 0 0 2125799863 0 77778.304 0 Non-medium error count: 173 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 11 - [- - -] # 2 Reserved(7) Completed 48 11 - [- - -] # 3 Background short Completed 64 10 - [- - -] # 4 Reserved(7) Completed 48 7 - [- - -] # 5 Background short Completed 64 6 - [- - -] # 6 Reserved(7) Completed 48 5 - [- - -] # 7 Background short Completed 64 3 - [- - -] # 8 Reserved(7) Completed 48 2 - [- - -] # 9 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 1905 seconds [31.8 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 55410:12 [3324612 minutes] Number of background scans performed: 767, scan progress: 0.00% Number of background medium scans performed: 767 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 10 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50063274bb9 attached SAS address = 0x544a842013b42905 attached phy identifier = 6 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 15 Phy reset problem count = 0 relative target port id = 2 generation code = 10 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50063274bba attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST300MM0006 Revision: LS0A Compliance: SPC-4 User Capacity: 300,000,000,000 bytes [300 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c50063270d5b Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Feb 26 11:28:14 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 50 C Manufactured in week 52 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 82 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 2387 Elements in grown defect list: 1 Vendor (Seagate Cache) information Blocks sent to initiator = 1722532410 Blocks received from initiator = 3462681226 Blocks read from cache and sent to initiator = 558533603 Number of read and write commands whose size <= segment size = 486127248 Number of read and write commands whose size > segment size = 86 Vendor (Seagate/Hitachi) factory information number of hours powered up = 55410.28 number of minutes until next internal SMART test = 48 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 1779455924 0 0 1779455924 0 4083.798 0 write: 0 0 12 12 16 34311.410 3 verify: 3868949439 0 0 3868949439 0 77758.272 0 Non-medium error count: 32 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 11 - [- - -] # 2 Reserved(7) Completed 48 11 - [- - -] # 3 Background short Completed 64 10 - [- - -] # 4 Reserved(7) Completed 48 7 - [- - -] # 5 Background short Completed 64 6 - [- - -] # 6 Reserved(7) Completed 48 5 - [- - -] # 7 Background short Completed 64 3 - [- - -] # 8 Reserved(7) Completed 48 2 - [- - -] # 9 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 1905 seconds [31.8 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 55410:17 [3324617 minutes] Number of background scans performed: 767, scan progress: 0.00% Number of background medium scans performed: 767 # when lba(hex) [sk,asc,ascq] reassign_status 1 54328:49 0000000000e2d6a5 [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 10 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50063270d59 attached SAS address = 0x544a842013b42903 attached phy identifier = 2 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 1547 Phy reset problem count = 0 relative target port id = 2 generation code = 10 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50063270d5a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_04 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST300MM0006 Revision: LS0A Compliance: SPC-4 User Capacity: 300,000,000,000 bytes [300 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c500632794bf Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Feb 26 11:28:15 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 50 C Manufactured in week 52 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 82 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 2390 Elements in grown defect list: 1 Vendor (Seagate Cache) information Blocks sent to initiator = 3547159561 Blocks received from initiator = 1668121249 Blocks read from cache and sent to initiator = 811885022 Number of read and write commands whose size <= segment size = 487510767 Number of read and write commands whose size > segment size = 81 Vendor (Seagate/Hitachi) factory information number of hours powered up = 55409.80 number of minutes until next internal SMART test = 51 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 552600300 0 0 552600300 0 4978.083 0 write: 0 0 234 234 237 35598.427 2 verify: 544878468 0 0 544878468 0 77695.117 0 Non-medium error count: 66 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 11 - [- - -] # 2 Reserved(7) Completed 48 11 - [- - -] # 3 Background short Completed 64 10 - [- - -] # 4 Reserved(7) Completed 48 7 - [- - -] # 5 Background short Completed 64 6 - [- - -] # 6 Reserved(7) Completed 48 5 - [- - -] # 7 Background short Completed 64 3 - [- - -] # 8 Reserved(7) Completed 48 2 - [- - -] # 9 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 1905 seconds [31.8 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 55409:48 [3324588 minutes] Number of background scans performed: 767, scan progress: 0.00% Number of background medium scans performed: 767 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 10 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500632794bd attached SAS address = 0x544a842013b42904 attached phy identifier = 5 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 15 Phy reset problem count = 0 relative target port id = 2 generation code = 10 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500632794be attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST300MM0006 Revision: LS0A Compliance: SPC-4 User Capacity: 300,000,000,000 bytes [300 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c500632871b3 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Feb 26 11:28:16 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 50 C Manufactured in week 52 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 82 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 2389 Elements in grown defect list: 2 Vendor (Seagate Cache) information Blocks sent to initiator = 1818842753 Blocks received from initiator = 2902171157 Blocks read from cache and sent to initiator = 561598532 Number of read and write commands whose size <= segment size = 488460777 Number of read and write commands whose size > segment size = 84 Vendor (Seagate/Hitachi) factory information number of hours powered up = 55410.42 number of minutes until next internal SMART test = 52 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 594150916 0 0 594150916 0 4131.990 1 write: 0 0 42 42 45 36211.036 4 verify: 1834989559 0 0 1834989559 0 77656.312 0 Non-medium error count: 102 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 12 - [- - -] # 2 Reserved(7) Completed 48 12 - [- - -] # 3 Background short Completed 64 10 - [- - -] # 4 Reserved(7) Completed 48 7 - [- - -] # 5 Background short Completed 64 6 - [- - -] # 6 Reserved(7) Completed 48 5 - [- - -] # 7 Background short Completed 64 3 - [- - -] # 8 Reserved(7) Completed 48 2 - [- - -] # 9 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 1905 seconds [31.8 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 55410:25 [3324625 minutes] Number of background scans performed: 767, scan progress: 0.00% Number of background medium scans performed: 767 # when lba(hex) [sk,asc,ascq] reassign_status 1 44223:07 000000000ce7aee9 [1,17,1] Recovered via rewrite in-place 2 45303:00 0000000000001b3c [1,17,1] Recovered via rewrite in-place 3 45447:00 0000000000001b3c [1,17,1] Recovered via rewrite in-place 4 50418:32 0000000000001b3c [1,17,1] Recovered via rewrite in-place 5 50850:34 0000000000001b3c [1,17,1] Recovered via rewrite in-place 6 50994:34 0000000000001b3c [1,17,1] Recovered via rewrite in-place 7 54040:59 0000000000001b3c [1,17,1] Recovered via rewrite in-place 8 54689:02 0000000000001b3c [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 10 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500632871b1 attached SAS address = 0x544a842013b42902 attached phy identifier = 1 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 8937 Phy reset problem count = 0 relative target port id = 2 generation code = 10 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500632871b2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sdc,megaraid_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG SSD SM841 2.5" 7mm 256GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: DXM02D0Q User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 26 11:28:18 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12480) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 20) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 176 175 Program_Fail_Count_Chip -O--CK 100 100 010 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 010 - 0 177 Wear_Leveling_Count PO--C- 058 058 005 - 1522 178 Used_Rsvd_Blk_Cnt_Chip PO--C- 100 100 010 - 0 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 9152 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 241 Total_LBAs_Written -O--CK 099 099 000 - 94792794075 242 Total_LBAs_Read -O--CK 099 099 000 - 20428190975 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 1 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 16 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 23/40 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 11 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 11 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: SAMSUNG SSD SM841 2.5" 7mm 256GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: DXM02D0Q User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Feb 26 11:28:18 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12480) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 20) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 173 175 Program_Fail_Count_Chip -O--CK 100 100 010 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 010 - 0 177 Wear_Leveling_Count PO--C- 086 086 005 - 494 178 Used_Rsvd_Blk_Cnt_Chip PO--C- 100 100 010 - 0 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 180 Unused_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 9152 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 241 Total_LBAs_Written -O--CK 099 099 000 - 45201110189 242 Total_LBAs_Read -O--CK 099 099 000 - 18434373821 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 1 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 16 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 26 Celsius Power Cycle Min/Max Temperature: 22/40 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc,megaraid_disk_02 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST300MM0006 Revision: LS0A Compliance: SPC-4 User Capacity: 300,000,000,000 bytes [300 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c50063274bbb Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Feb 26 11:28:18 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 50 C Manufactured in week 52 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 82 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 2386 Elements in grown defect list: 1 Vendor (Seagate Cache) information Blocks sent to initiator = 3407275802 Blocks received from initiator = 92561315 Blocks read from cache and sent to initiator = 810024897 Number of read and write commands whose size <= segment size = 503650817 Number of read and write commands whose size > segment size = 97 Vendor (Seagate/Hitachi) factory information number of hours powered up = 55410.20 number of minutes until next internal SMART test = 50 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 761362932 0 0 761362932 0 4913.470 0 write: 0 0 12 12 13 30553.603 1 verify: 2125799863 0 0 2125799863 0 77778.304 0 Non-medium error count: 173 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 11 - [- - -] # 2 Reserved(7) Completed 48 11 - [- - -] # 3 Background short Completed 64 10 - [- - -] # 4 Reserved(7) Completed 48 7 - [- - -] # 5 Background short Completed 64 6 - [- - -] # 6 Reserved(7) Completed 48 5 - [- - -] # 7 Background short Completed 64 3 - [- - -] # 8 Reserved(7) Completed 48 2 - [- - -] # 9 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 1905 seconds [31.8 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 55410:12 [3324612 minutes] Number of background scans performed: 767, scan progress: 0.00% Number of background medium scans performed: 767 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 10 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50063274bb9 attached SAS address = 0x544a842013b42905 attached phy identifier = 6 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 15 Phy reset problem count = 0 relative target port id = 2 generation code = 10 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50063274bba attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sdc,megaraid_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST300MM0006 Revision: LS0A Compliance: SPC-4 User Capacity: 300,000,000,000 bytes [300 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c50063270d5b Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Feb 26 11:28:19 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 50 C Manufactured in week 52 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 82 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 2387 Elements in grown defect list: 1 Vendor (Seagate Cache) information Blocks sent to initiator = 1722538468 Blocks received from initiator = 3462685408 Blocks read from cache and sent to initiator = 558535219 Number of read and write commands whose size <= segment size = 486127329 Number of read and write commands whose size > segment size = 86 Vendor (Seagate/Hitachi) factory information number of hours powered up = 55410.28 number of minutes until next internal SMART test = 48 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 1779466254 0 0 1779466254 0 4083.801 0 write: 0 0 12 12 16 34311.419 3 verify: 3868949439 0 0 3868949439 0 77758.272 0 Non-medium error count: 32 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 11 - [- - -] # 2 Reserved(7) Completed 48 11 - [- - -] # 3 Background short Completed 64 10 - [- - -] # 4 Reserved(7) Completed 48 7 - [- - -] # 5 Background short Completed 64 6 - [- - -] # 6 Reserved(7) Completed 48 5 - [- - -] # 7 Background short Completed 64 3 - [- - -] # 8 Reserved(7) Completed 48 2 - [- - -] # 9 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 1905 seconds [31.8 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 55410:17 [3324617 minutes] Number of background scans performed: 767, scan progress: 0.00% Number of background medium scans performed: 767 # when lba(hex) [sk,asc,ascq] reassign_status 1 54328:49 0000000000e2d6a5 [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 10 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50063270d59 attached SAS address = 0x544a842013b42903 attached phy identifier = 2 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 1547 Phy reset problem count = 0 relative target port id = 2 generation code = 10 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50063270d5a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sdc,megaraid_disk_04 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST300MM0006 Revision: LS0A Compliance: SPC-4 User Capacity: 300,000,000,000 bytes [300 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c500632794bf Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Feb 26 11:28:19 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 50 C Manufactured in week 52 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 82 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 2390 Elements in grown defect list: 1 Vendor (Seagate Cache) information Blocks sent to initiator = 3547164225 Blocks received from initiator = 1668123641 Blocks read from cache and sent to initiator = 811888206 Number of read and write commands whose size <= segment size = 487510795 Number of read and write commands whose size > segment size = 81 Vendor (Seagate/Hitachi) factory information number of hours powered up = 55409.80 number of minutes until next internal SMART test = 51 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 552608487 0 0 552608487 0 4978.085 0 write: 0 0 234 234 237 35598.428 2 verify: 544878468 0 0 544878468 0 77695.117 0 Non-medium error count: 66 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 11 - [- - -] # 2 Reserved(7) Completed 48 11 - [- - -] # 3 Background short Completed 64 10 - [- - -] # 4 Reserved(7) Completed 48 7 - [- - -] # 5 Background short Completed 64 6 - [- - -] # 6 Reserved(7) Completed 48 5 - [- - -] # 7 Background short Completed 64 3 - [- - -] # 8 Reserved(7) Completed 48 2 - [- - -] # 9 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 1905 seconds [31.8 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 55409:48 [3324588 minutes] Number of background scans performed: 767, scan progress: 0.00% Number of background medium scans performed: 767 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 10 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500632794bd attached SAS address = 0x544a842013b42904 attached phy identifier = 5 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 15 Phy reset problem count = 0 relative target port id = 2 generation code = 10 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500632794be attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sdc,megaraid_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-8-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST300MM0006 Revision: LS0A Compliance: SPC-4 User Capacity: 300,000,000,000 bytes [300 GB] Logical block size: 512 bytes LU is fully provisioned Rotation Rate: 10000 rpm Form Factor: 2.5 inches Logical Unit id: 0x5000c500632871b3 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Mon Feb 26 11:28:20 2024 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 50 C Manufactured in week 52 of year 2014 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 82 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 2389 Elements in grown defect list: 2 Vendor (Seagate Cache) information Blocks sent to initiator = 1818849793 Blocks received from initiator = 2902175041 Blocks read from cache and sent to initiator = 561601092 Number of read and write commands whose size <= segment size = 488460860 Number of read and write commands whose size > segment size = 84 Vendor (Seagate/Hitachi) factory information number of hours powered up = 55410.42 number of minutes until next internal SMART test = 52 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 594162971 0 0 594162971 0 4131.994 1 write: 0 0 42 42 45 36211.038 4 verify: 1834989559 0 0 1834989559 0 77656.312 0 Non-medium error count: 102 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 64 12 - [- - -] # 2 Reserved(7) Completed 48 12 - [- - -] # 3 Background short Completed 64 10 - [- - -] # 4 Reserved(7) Completed 48 7 - [- - -] # 5 Background short Completed 64 6 - [- - -] # 6 Reserved(7) Completed 48 5 - [- - -] # 7 Background short Completed 64 3 - [- - -] # 8 Reserved(7) Completed 48 2 - [- - -] # 9 Background short Completed 64 1 - [- - -] Long (extended) Self-test duration: 1905 seconds [31.8 minutes] Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 55410:25 [3324625 minutes] Number of background scans performed: 767, scan progress: 0.00% Number of background medium scans performed: 767 # when lba(hex) [sk,asc,ascq] reassign_status 1 44223:07 000000000ce7aee9 [1,17,1] Recovered via rewrite in-place 2 45303:00 0000000000001b3c [1,17,1] Recovered via rewrite in-place 3 45447:00 0000000000001b3c [1,17,1] Recovered via rewrite in-place 4 50418:32 0000000000001b3c [1,17,1] Recovered via rewrite in-place 5 50850:34 0000000000001b3c [1,17,1] Recovered via rewrite in-place 6 50994:34 0000000000001b3c [1,17,1] Recovered via rewrite in-place 7 54040:59 0000000000001b3c [1,17,1] Recovered via rewrite in-place 8 54689:02 0000000000001b3c [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 10 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500632871b1 attached SAS address = 0x544a842013b42902 attached phy identifier = 1 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 8937 Phy reset problem count = 0 relative target port id = 2 generation code = 10 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500632871b2 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0