/dev/sda,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SK hynix SATA SSDs Device Model: SK hynix SC311 SATA 256GB Serial Number: -- Firmware Version: 70000P10 User Capacity: 256,060,514,304 bytes [256 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-3 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Sep 21 14:20:26 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 110) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 166 166 006 - 0 5 Retired_Block_Count -O--CK 253 253 036 - 0 9 Power_On_Hours -O--CK 056 056 000 - 39210 12 Power_Cycle_Count -O--CK 100 100 020 - 44 100 Total_Erase_Count -O--CK 100 100 000 - 34764585 168 Min_Erase_Count -O--CK 021 021 000 - 1199 169 Max_Erase_Count -O--CK 017 017 000 - 1264 174 Unexpect_Power_Loss_Ct ----CK 100 100 000 - 29 175 Program_Fail_Count_Chip -O--CK 253 253 000 - 0 176 Unused_Rsvd_Blk_Cnt_Tot -O--CK 253 253 000 - 0 177 Wear_Leveling_Count -O--CK 019 001 000 - 1228 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 253 253 000 - 0 179 Used_Rsvd_Blk_Cnt_Tot -O--CK 253 253 000 - 0 180 Erase_Fail_Count -O--CK 100 100 000 - 716 181 Non4k_Aligned_Access -O--CK 253 253 000 - 0 182 Erase_Fail_Count_Total -O--CK 253 253 000 - 0 184 End-to-End_Error -O--CK 253 253 000 - 0 187 Reported_Uncorrect -O--CK 253 253 000 - 0 188 Command_Timeout -O--CK 253 253 000 - 0 194 Temperature_Celsius -O---- 023 016 000 - 23 (Min/Max 16/44) 195 Hardware_ECC_Recovered -O--CK 253 253 000 - 0 196 Reallocated_Event_Count -O--CK 253 253 036 - 0 198 Offline_Uncorrectable -O--CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 253 253 000 - 0 204 Soft_ECC_Correction -OSR-- 001 001 000 - 7922656 212 Phy_Error_Count -O--CK 100 100 000 - 322 233 Media_Wearout_Indicator -O--CK 083 001 000 - 18 234 Unknown_SK_hynix_Attrib -O--CK 100 100 000 - 640728531456 241 Total_Writes_GB -O--CK 100 100 000 - 522570457723 242 Total_Reads_GB -O--CK 100 100 000 - 114447583196 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 4 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 31473 - # 2 Short offline Completed without error 00% 2 - # 3 Extended offline Completed without error 00% 2 - Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum. SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 23 Celsius Power Cycle Min/Max Temperature: 1/-1 Celsius Lifetime Min/Max Temperature: 1/-1 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 174569/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 44 --- Lifetime Power-On Resets 0x01 0x010 4 39210 --- Power-on Hours 0x01 0x018 6 522570457723 --- Logical Sectors Written 0x01 0x020 6 2383380363 --- Number of Write Commands 0x01 0x028 6 114447583196 --- Logical Sectors Read 0x01 0x030 6 1010075963 --- Number of Read Commands 0x01 0x038 6 3717046528 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 23 --- Current Temperature 0x05 0x010 1 24 --- Average Short Term Temperature 0x05 0x018 1 21 --- Average Long Term Temperature 0x05 0x020 1 -1 --- Highest Temperature 0x05 0x028 1 1 --- Lowest Temperature 0x05 0x030 1 - --- Highest Average Short Term Temperature 0x05 0x038 1 19 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 21 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 80 --- Specified Maximum Operating Temperature 0x05 0x060 4 2308030 --- Time in Under-Temperature 0x05 0x068 1 -20 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 406 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 81 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET /dev/sdc,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SK hynix SATA SSDs Device Model: SK hynix SC311 SATA 256GB Serial Number: -- Firmware Version: 70000P10 User Capacity: 256,060,514,304 bytes [256 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-3 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Sep 21 14:20:26 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 110) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 166 166 006 - 0 5 Retired_Block_Count -O--CK 253 253 036 - 0 9 Power_On_Hours -O--CK 056 056 000 - 39210 12 Power_Cycle_Count -O--CK 100 100 020 - 44 100 Total_Erase_Count -O--CK 100 100 000 - 34764585 168 Min_Erase_Count -O--CK 021 021 000 - 1199 169 Max_Erase_Count -O--CK 017 017 000 - 1264 174 Unexpect_Power_Loss_Ct ----CK 100 100 000 - 29 175 Program_Fail_Count_Chip -O--CK 253 253 000 - 0 176 Unused_Rsvd_Blk_Cnt_Tot -O--CK 253 253 000 - 0 177 Wear_Leveling_Count -O--CK 019 001 000 - 1228 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 253 253 000 - 0 179 Used_Rsvd_Blk_Cnt_Tot -O--CK 253 253 000 - 0 180 Erase_Fail_Count -O--CK 100 100 000 - 716 181 Non4k_Aligned_Access -O--CK 253 253 000 - 0 182 Erase_Fail_Count_Total -O--CK 253 253 000 - 0 184 End-to-End_Error -O--CK 253 253 000 - 0 187 Reported_Uncorrect -O--CK 253 253 000 - 0 188 Command_Timeout -O--CK 253 253 000 - 0 194 Temperature_Celsius -O---- 023 016 000 - 23 (Min/Max 16/44) 195 Hardware_ECC_Recovered -O--CK 253 253 000 - 0 196 Reallocated_Event_Count -O--CK 253 253 036 - 0 198 Offline_Uncorrectable -O--CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 253 253 000 - 0 204 Soft_ECC_Correction -OSR-- 001 001 000 - 7922656 212 Phy_Error_Count -O--CK 100 100 000 - 322 233 Media_Wearout_Indicator -O--CK 083 001 000 - 18 234 Unknown_SK_hynix_Attrib -O--CK 100 100 000 - 640728531456 241 Total_Writes_GB -O--CK 100 100 000 - 522570457723 242 Total_Reads_GB -O--CK 100 100 000 - 114447583292 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 4 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 31473 - # 2 Short offline Completed without error 00% 2 - # 3 Extended offline Completed without error 00% 2 - Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum. SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 23 Celsius Power Cycle Min/Max Temperature: 1/-1 Celsius Lifetime Min/Max Temperature: 1/-1 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 174569/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 44 --- Lifetime Power-On Resets 0x01 0x010 4 39210 --- Power-on Hours 0x01 0x018 6 522570457723 --- Logical Sectors Written 0x01 0x020 6 2383380363 --- Number of Write Commands 0x01 0x028 6 114447583292 --- Logical Sectors Read 0x01 0x030 6 1010075975 --- Number of Read Commands 0x01 0x038 6 3717046528 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 23 --- Current Temperature 0x05 0x010 1 24 --- Average Short Term Temperature 0x05 0x018 1 21 --- Average Long Term Temperature 0x05 0x020 1 -1 --- Highest Temperature 0x05 0x028 1 1 --- Lowest Temperature 0x05 0x030 1 - --- Highest Average Short Term Temperature 0x05 0x038 1 19 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 21 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 80 --- Specified Maximum Operating Temperature 0x05 0x060 4 2308030 --- Time in Under-Temperature 0x05 0x068 1 -20 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 406 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 81 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET /dev/sdc,megaraid_disk_02 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SK hynix SATA SSDs Device Model: SK hynix SC311 SATA 256GB Serial Number: -- Firmware Version: 70000P10 User Capacity: 256,060,514,304 bytes [256 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-3 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Sep 21 14:20:26 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 110) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 166 166 006 - 0 5 Retired_Block_Count -O--CK 253 253 036 - 0 9 Power_On_Hours -O--CK 055 055 000 - 40629 12 Power_Cycle_Count -O--CK 100 100 020 - 40 100 Total_Erase_Count -O--CK 100 100 000 - 34951334 168 Min_Erase_Count -O--CK 021 021 000 - 1204 169 Max_Erase_Count -O--CK 017 017 000 - 1268 174 Unexpect_Power_Loss_Ct ----CK 100 100 000 - 27 175 Program_Fail_Count_Chip -O--CK 253 253 000 - 0 176 Unused_Rsvd_Blk_Cnt_Tot -O--CK 253 253 000 - 0 177 Wear_Leveling_Count -O--CK 019 001 000 - 1233 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 253 253 000 - 0 179 Used_Rsvd_Blk_Cnt_Tot -O--CK 253 253 000 - 0 180 Erase_Fail_Count -O--CK 100 100 000 - 734 181 Non4k_Aligned_Access -O--CK 253 253 000 - 0 182 Erase_Fail_Count_Total -O--CK 253 253 000 - 0 184 End-to-End_Error -O--CK 253 253 000 - 0 187 Reported_Uncorrect -O--CK 253 253 000 - 0 188 Command_Timeout -O--CK 253 253 000 - 0 194 Temperature_Celsius -O---- 024 017 000 - 24 (Min/Max 17/42) 195 Hardware_ECC_Recovered -O--CK 253 253 000 - 0 196 Reallocated_Event_Count -O--CK 253 253 036 - 0 198 Offline_Uncorrectable -O--CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 253 253 000 - 0 204 Soft_ECC_Correction -OSR-- 001 001 000 - 8945932 212 Phy_Error_Count -O--CK 100 100 000 - 252 233 Media_Wearout_Indicator -O--CK 083 001 000 - 18 234 Unknown_SK_hynix_Attrib -O--CK 100 100 000 - 644175964032 241 Total_Writes_GB -O--CK 100 100 000 - 522219824390 242 Total_Reads_GB -O--CK 100 100 000 - 118690335414 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 4 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 32894 - # 2 Short offline Completed without error 00% 2 - # 3 Extended offline Completed without error 00% 2 - Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum. SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 1/-1 Celsius Lifetime Min/Max Temperature: 1/-1 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 174573/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 40 --- Lifetime Power-On Resets 0x01 0x010 4 40629 --- Power-on Hours 0x01 0x018 6 522219824390 --- Logical Sectors Written 0x01 0x020 6 2398405253 --- Number of Write Commands 0x01 0x028 6 118690335414 --- Logical Sectors Read 0x01 0x030 6 1041409336 --- Number of Read Commands 0x01 0x038 6 235511936 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 24 --- Current Temperature 0x05 0x010 1 25 --- Average Short Term Temperature 0x05 0x018 1 23 --- Average Long Term Temperature 0x05 0x020 1 -1 --- Highest Temperature 0x05 0x028 1 1 --- Lowest Temperature 0x05 0x030 1 - --- Highest Average Short Term Temperature 0x05 0x038 1 20 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 23 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 80 --- Specified Maximum Operating Temperature 0x05 0x060 4 2395790 --- Time in Under-Temperature 0x05 0x068 1 -20 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 324 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 82 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET /dev/sdc,megaraid_disk_04 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST6000NM0034 Revision: MS2A Compliance: SPC-4 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c50084561427 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sun Sep 21 14:20:26 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: DATA CHANNEL IMPENDING FAILURE GENERAL HARD DRIVE FAILURE [asc=5d, ascq=30] Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned = 64 Power on minutes since format <not available> Current Drive Temperature: 28 C Drive Trip Temperature: 60 C Manufactured in week 40 of year 2015 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 124 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 14402 Elements in grown defect list: 64 Vendor (Seagate Cache) information Blocks sent to initiator = 2769119400 Blocks received from initiator = 3647869312 Blocks read from cache and sent to initiator = 1858978446 Number of read and write commands whose size <= segment size = 3724173327 Number of read and write commands whose size > segment size = 5779802 Vendor (Seagate/Hitachi) factory information number of hours powered up = 50350.85 number of minutes until next internal SMART test = 47 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 673535950 408 0 673536358 481 1899846.932 50 write: 0 0 67 67 68 386218.772 0 verify: 958484706 0 0 958484706 0 1248373.136 0 Non-medium error count: 305 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 80 42560 - [- - -] # 2 Background short Completed 80 4 - [- - -] # 3 Reserved(7) Completed 64 3 - [- - -] # 4 Background short Completed 80 1 - [- - -] Long (extended) Self-test duration: 38632 seconds [10.7 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 50350:51 [3021051 minutes] Number of background scans performed: 143, scan progress: 35.54% Number of background medium scans performed: 143 # when lba(hex) [sk,asc,ascq] reassign_status 1 47144:04 00000002b4cab890 [1,18,4] Recovered via rewrite in-place 2 47146:49 00000002b734d840 [1,18,4] Recovered via rewrite in-place 3 47146:50 00000002b826dad8 [3,11,0] Require Write or Reassign Blocks command 4 47146:50 00000002b826dae0 [3,11,0] Require Write or Reassign Blocks command 5 47146:50 00000002b826dae8 [3,11,0] Require Write or Reassign Blocks command 6 47146:50 00000002b826daf0 [3,11,0] Require Write or Reassign Blocks command 7 47146:50 00000002b826daf8 [3,11,0] Require Write or Reassign Blocks command 8 47146:50 00000002b826db00 [3,11,0] Require Write or Reassign Blocks command 9 47146:50 00000002b826db08 [3,11,0] Require Write or Reassign Blocks command 10 47146:50 00000002b826db10 [3,11,0] Require Write or Reassign Blocks command 11 47146:50 00000002b826db18 [1,18,4] Recovered via rewrite in-place 12 47230:48 00000002b80919d0 [1,18,4] Recovered via rewrite in-place 13 47230:48 00000002b80919e0 [3,11,0] Require Write or Reassign Blocks command Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c50084561425 attached SAS address = 0x500056b3528fd7ff attached phy identifier = 4 Invalid DWORD count = 16 Running disparity error count = 16 Loss of DWORD synchronization count = 6 Phy reset problem count = 7 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50084561426 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sdc,megaraid_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST6000NM0034 Revision: MS2D Compliance: SPC-4 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5008f842b87 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sun Sep 21 14:20:27 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 31 C Drive Trip Temperature: 60 C Manufactured in week 45 of year 2015 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 59 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 8825 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 2466830496 Blocks received from initiator = 217646528 Blocks read from cache and sent to initiator = 1342729430 Number of read and write commands whose size <= segment size = 695524373 Number of read and write commands whose size > segment size = 419786 Vendor (Seagate/Hitachi) factory information number of hours powered up = 39533.87 number of minutes until next internal SMART test = 10 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 3382697047 0 0 3382697047 0 819299.670 0 write: 0 0 0 0 0 39717.877 0 verify: 2628743192 0 0 2628743192 0 0.000 0 Non-medium error count: 10 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 64 2 - [- - -] # 2 Background short Completed 96 0 - [- - -] Long (extended) Self-test duration: 38632 seconds [10.7 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 39533:52 [2372032 minutes] Number of background scans performed: 208, scan progress: 59.11% Number of background medium scans performed: 208 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c5008f842b85 attached SAS address = 0x500056b3528fd7ff attached phy identifier = 5 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 4 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5008f842b86 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 76 Phy reset problem count = 0 /dev/sdc,megaraid_disk_07 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST6000NM0034 Revision: MS2D Compliance: SPC-4 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5008f818c17 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sun Sep 21 14:20:28 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 31 C Drive Trip Temperature: 60 C Manufactured in week 45 of year 2015 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 101 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 8924 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 3551358192 Blocks received from initiator = 524399752 Blocks read from cache and sent to initiator = 649294344 Number of read and write commands whose size <= segment size = 763030806 Number of read and write commands whose size > segment size = 761320 Vendor (Seagate/Hitachi) factory information number of hours powered up = 41221.02 number of minutes until next internal SMART test = 7 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 3749797200 0 0 3749797200 0 837447.137 0 write: 0 0 6 6 6 42076.842 0 verify: 2680912752 0 0 2680912752 0 0.000 0 Non-medium error count: 18 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 64 3 - [- - -] # 2 Background short Completed 96 2 - [- - -] Long (extended) Self-test duration: 38632 seconds [10.7 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 41221:01 [2473261 minutes] Number of background scans performed: 225, scan progress: 58.10% Number of background medium scans performed: 225 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c5008f818c15 attached SAS address = 0x500056b3528fd7ff attached phy identifier = 7 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 8 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5008f818c16 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 3 Phy reset problem count = 0 /dev/sdc,megaraid_disk_08 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST6000NM0034 Revision: MS2A Compliance: SPC-4 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c50084573af7 Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sun Sep 21 14:20:30 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 34 C Drive Trip Temperature: 60 C Manufactured in week 40 of year 2015 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 124 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 11401 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 1972655408 Blocks received from initiator = 553039936 Blocks read from cache and sent to initiator = 2306515972 Number of read and write commands whose size <= segment size = 3949264914 Number of read and write commands whose size > segment size = 6343410 Vendor (Seagate/Hitachi) factory information number of hours powered up = 50350.90 number of minutes until next internal SMART test = 0 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 1754264963 21 0 1754264984 21 2211698.553 0 write: 0 0 8 8 8 400301.165 0 verify: 1053787851 0 0 1053787851 0 1248375.033 0 Non-medium error count: 3 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Background short Completed 80 42560 - [- - -] # 2 Background short Completed 80 4 - [- - -] # 3 Reserved(7) Completed 64 3 - [- - -] # 4 Background short Completed 80 1 - [- - -] Long (extended) Self-test duration: 38632 seconds [10.7 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 50350:54 [3021054 minutes] Number of background scans performed: 147, scan progress: 19.03% Number of background medium scans performed: 147 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c50084573af5 attached SAS address = 0x500056b3528fd7ff attached phy identifier = 8 Invalid DWORD count = 8 Running disparity error count = 8 Loss of DWORD synchronization count = 4 Phy reset problem count = 5 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c50084573af6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sdc,megaraid_disk_10 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST6000NM0034 Revision: MS2D Compliance: SPC-4 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5008f7eabcf Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sun Sep 21 14:20:32 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 32 C Drive Trip Temperature: 60 C Manufactured in week 45 of year 2015 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 100 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 8821 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 4169468848 Blocks received from initiator = 652865312 Blocks read from cache and sent to initiator = 3597180985 Number of read and write commands whose size <= segment size = 679460901 Number of read and write commands whose size > segment size = 249746 Vendor (Seagate/Hitachi) factory information number of hours powered up = 39523.45 number of minutes until next internal SMART test = 49 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 3612117605 0 0 3612117605 0 782788.029 0 write: 0 0 1 1 1 39941.233 0 Non-medium error count: 17 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 64 2 - [- - -] # 2 Background short Completed 96 0 - [- - -] Long (extended) Self-test duration: 38632 seconds [10.7 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 39523:27 [2371407 minutes] Number of background scans performed: 208, scan progress: 75.67% Number of background medium scans performed: 208 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c5008f7eabcd attached SAS address = 0x500056b3528fd7ff attached phy identifier = 10 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 4 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5008f7eabce attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sdc,megaraid_disk_11 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST6000NM0034 Revision: MS2D Compliance: SPC-4 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5008f84809b Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Sun Sep 21 14:20:33 2025 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Disabled or Not Supported Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 33 C Drive Trip Temperature: 60 C Manufactured in week 45 of year 2015 Specified cycle count over device lifetime: 10000 Accumulated start-stop cycles: 60 Specified load-unload count over device lifetime: 300000 Accumulated load-unload cycles: 8870 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 1873695480 Blocks received from initiator = 3448874936 Blocks read from cache and sent to initiator = 89998093 Number of read and write commands whose size <= segment size = 715014608 Number of read and write commands whose size > segment size = 624672 Vendor (Seagate/Hitachi) factory information number of hours powered up = 41208.48 number of minutes until next internal SMART test = 59 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 3516796613 0 0 3516796613 0 803602.826 0 write: 0 0 1 1 1 39175.602 0 Non-medium error count: 10 SMART Self-test log Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ] Description number (hours) # 1 Reserved(7) Completed 64 2 - [- - -] # 2 Background short Completed 96 0 - [- - -] Long (extended) Self-test duration: 38632 seconds [10.7 hours] Background scan results log Status: scan is active Accumulated power on time, hours:minutes 41208:29 [2472509 minutes] Number of background scans performed: 226, scan progress: 30.08% Number of background medium scans performed: 226 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c5008f848099 attached SAS address = 0x500056b3528fd7ff attached phy identifier = 11 Invalid DWORD count = 4 Running disparity error count = 4 Loss of DWORD synchronization count = 4 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5008f84809a attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0