/dev/sda,megaraid_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital RE3 Serial ATA Device Model: WD2502ABYS-23B7A0 39M4511 42C0463IBM Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.03B07 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:04 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4680) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 58) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 200 199 021 - 975 4 Start_Stop_Count -O--CK 100 100 000 - 115 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 005 005 000 - 70011 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 114 192 Power-Off_Retract_Count -O--CK 200 200 000 - 112 193 Load_Cycle_Count -O--CK 200 200 000 - 2 194 Temperature_Celsius -O---K 123 103 000 - 20 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 20 Celsius Power Cycle Min/Max Temperature: 17/22 Celsius Lifetime Min/Max Temperature: 19/40 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x8000 4 225218 Vendor specific /dev/sda,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital RE3 Serial ATA Device Model: WD2502ABYS-23B7A0 39M4511 42C0463IBM Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.03B07 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:04 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4680) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 58) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 200 199 021 - 991 4 Start_Stop_Count -O--CK 100 100 000 - 73 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 020 020 000 - 58642 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 72 192 Power-Off_Retract_Count -O--CK 200 200 000 - 57 193 Load_Cycle_Count -O--CK 200 200 000 - 15 194 Temperature_Celsius -O---K 124 101 000 - 19 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 36656 hours (1527 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 13 34 00 f0 00 40 00 Error: IDNF at LBA = 0x133400f000 = 82476855296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 05 00 00 b0 00 00 13 f0 34 00 40 08 00:11:51.129 WRITE FPDMA QUEUED 61 04 80 00 a8 00 00 13 f0 2f 80 40 08 00:11:51.121 WRITE FPDMA QUEUED 61 02 80 00 a0 00 00 13 f0 2d 00 40 08 00:11:51.115 WRITE FPDMA QUEUED 61 08 80 00 98 00 00 13 f0 24 80 40 08 00:11:51.110 WRITE FPDMA QUEUED 61 05 00 00 90 00 00 13 f0 1f 80 40 08 00:11:51.098 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 17 Celsius Power Cycle Min/Max Temperature: 16/21 Celsius Lifetime Min/Max Temperature: 17/42 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x8000 4 225219 Vendor specific /dev/sda,megaraid_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: MG04ACA200N 00YK039D7A01888LEN Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: TK44 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:04 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 232) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 3283 4 Start_Stop_Count -O--CK 100 100 000 - 206 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 083 083 000 - 7124 10 Spin_Retry_Count PO--CK 104 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 206 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 001 - 0 190 Airflow_Temperature_Cel -O---K 081 061 045 - 19 (Min/Max 17/20) 192 Power-Off_Retract_Count -O--CK 100 100 000 - 203 193 Load_Cycle_Count -O--CK 100 100 000 - 206 194 Temperature_Celsius -O---K 100 100 000 - 19 (Min/Max 15/39) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 253 000 - 0 212 Unknown_Attribute -O--CK 100 100 000 - 0 220 Disk_Shift -O---- 100 100 000 - 0 222 Loaded_Hours -O--CK 083 083 000 - 7121 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 546 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 12288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa7 GPL VS 8 Device vendor specific log 0xa8 GPL VS 7681 Device vendor specific log 0xb0 GPL,SL VS 1 Device vendor specific log 0xb1 GPL VS 12288 Device vendor specific log 0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 19 Celsius Power Cycle Min/Max Temperature: 17/20 Celsius Lifetime Min/Max Temperature: 15/39 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 206 --- Lifetime Power-On Resets 0x01 0x010 4 7124 --- Power-on Hours 0x01 0x018 6 307803767 --- Logical Sectors Written 0x01 0x020 6 986203 --- Number of Write Commands 0x01 0x028 6 27330620993 --- Logical Sectors Read 0x01 0x030 6 213540825 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 0 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 7121 --- Spindle Motor Power-on Hours 0x03 0x010 4 7121 --- Head Flying Hours 0x03 0x018 4 206 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 19 --- Current Temperature 0x05 0x010 1 18 N-- Average Short Term Temperature 0x05 0x018 1 16 N-- Average Long Term Temperature 0x05 0x020 1 39 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x030 1 27 N-- Highest Average Short Term Temperature 0x05 0x038 1 15 N-- Lowest Average Short Term Temperature 0x05 0x040 1 22 N-- Highest Average Long Term Temperature 0x05 0x048 1 16 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 44896 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sda,megaraid_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Purple Device Model: WDC WD40PURX-64GVNY0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:06 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (51840) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 518) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 171 171 021 - 8450 4 Start_Stop_Count -O--CK 100 100 000 - 318 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 077 077 000 - 17240 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 79 192 Power-Off_Retract_Count -O--CK 200 200 000 - 61 193 Load_Cycle_Count -O--CK 200 200 000 - 355 194 Temperature_Celsius -O---K 133 105 000 - 19 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 39 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 6041 hours (251 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 01 aa ad fc c0 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 3d+04:19:17.645 FLUSH CACHE EXT 61 00 08 00 50 00 00 00 5c 64 70 40 00 3d+03:59:18.124 WRITE FPDMA QUEUED 61 00 08 00 48 00 00 00 5c 64 80 40 00 3d+03:59:18.123 WRITE FPDMA QUEUED 61 00 08 00 40 00 00 00 64 75 58 40 00 3d+03:59:13.028 WRITE FPDMA QUEUED 61 00 08 00 38 00 00 00 5c 64 78 40 00 3d+03:59:07.834 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 19 Celsius Power Cycle Min/Max Temperature: 17/20 Celsius Lifetime Min/Max Temperature: 16/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 225236 Vendor specific /dev/sda,megaraid_disk_06 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST3600057SS Revision: 0008 Compliance: SPC-3 User Capacity: 600,127,266,816 bytes [600 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5003b8d8eef Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Dec 5 12:18:06 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 68 C Elements in grown defect list: 668 Vendor (Seagate Cache) information Blocks sent to initiator = 1438821285 Blocks received from initiator = 4292434641 Blocks read from cache and sent to initiator = 2949839783 Number of read and write commands whose size <= segment size = 2302975697 Number of read and write commands whose size > segment size = 0 Vendor (Seagate/Hitachi) factory information number of hours powered up = 65023.22 number of minutes until next internal SMART test = 25 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 1168962932 168 0 1168963100 1168963378 145872.211 278 write: 0 0 1 1 7 41996.684 1 verify: 137 0 0 137 144 0.000 3 Non-medium error count: 345 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 65023:13 [3901393 minutes] Number of background scans performed: 979, scan progress: 0.00% Number of background medium scans performed: 62171 # when lba(hex) [sk,asc,ascq] reassign_status 1 12968:43 0000000042e0b46c [1,18,1] Recovered via rewrite in-place 2 13000:52 0000000042e0b87e [3,11,0] Recovered via rewrite in-place 3 13000:52 0000000042e0b87f [3,11,0] Recovered via rewrite in-place 4 13000:52 0000000042e0bc90 [3,11,0] Recovered via rewrite in-place 5 13000:52 0000000042e0bc91 [3,11,0] Recovered via rewrite in-place 6 13000:52 0000000042e0bc92 [3,11,0] Recovered via rewrite in-place 7 13000:52 0000000042e0c0a3 [3,11,0] Recovered via rewrite in-place 8 13000:52 0000000042e0c4b5 [3,11,0] Recovered via rewrite in-place 9 13000:53 00000000436604ac [3,11,0] Recovered via rewrite in-place 10 13000:55 0000000044373d96 [1,17,3] Recovered via rewrite in-place 11 13000:55 0000000044373d97 [3,11,0] Recovered via rewrite in-place 12 13000:55 0000000044373d98 [3,11,0] Recovered via rewrite in-place 13 13000:55 000000004450bbca [3,11,0] Recovered via rewrite in-place 14 29816:10 00000000000abfb1 [1,18,1] Successfully reassigned 15 31418:07 00000000000ad314 [1,18,1] Successfully reassigned 16 31418:08 00000000000bbcf3 [1,17,2] Recovered via rewrite in-place 17 31513:53 00000000000accae [1,17,2] Successfully reassigned 18 31537:53 00000000000bb718 [1,17,3] Successfully reassigned 19 32304:11 00000000000af856 [1,17,3] Successfully reassigned 20 32661:48 000000003100a258 [1,17,1] Recovered via rewrite in-place 21 33056:00 00000000000ac1f5 [1,17,3] Successfully reassigned 22 33056:01 00000000000ae079 [3,11,0] Recovered via rewrite in-place 23 33056:02 00000000000ae07b [3,11,0] Successfully reassigned 24 33056:02 00000000000ae07d [3,11,0] Successfully reassigned 25 33056:02 00000000000ae07f [3,11,0] Successfully reassigned 26 33056:03 00000000000ae080 [3,11,0] Successfully reassigned 27 33056:03 00000000000ae081 [3,11,0] Successfully reassigned 28 33056:04 00000000000ae082 [3,11,0] Successfully reassigned 29 33056:04 00000000000ae09c [3,11,0] Successfully reassigned 30 33056:04 00000000000ae0ba [3,11,0] Successfully reassigned 31 33056:04 00000000000ae0bc [3,11,0] Successfully reassigned 32 33056:04 00000000000ae0be [3,11,0] Successfully reassigned 33 33056:05 00000000000ae0c1 [3,11,0] Successfully reassigned 34 33056:05 00000000000ae0c3 [3,11,0] Successfully reassigned 35 33056:05 00000000000ae0c5 [3,11,0] Successfully reassigned 36 33056:05 00000000000ae0c7 [3,11,0] Successfully reassigned 37 33056:05 00000000000ae0c9 [3,11,0] Successfully reassigned 38 33056:06 00000000000ae0cb [3,11,0] Successfully reassigned 39 33056:06 00000000000ae0cc [3,11,0] Successfully reassigned 40 33056:07 00000000000ae0ce [3,11,0] Successfully reassigned 41 33056:08 00000000000ae0d0 [3,11,0] Successfully reassigned 42 33056:10 00000000000ae0d6 [3,11,0] Successfully reassigned 43 33056:10 00000000000ae0d8 [1,17,2] Recovered via rewrite in-place 44 33056:10 00000000000ae0d9 [3,11,0] Successfully reassigned 45 33056:10 00000000000ae0db [3,11,0] Successfully reassigned 46 33056:10 00000000000ae0dd [3,11,0] Successfully reassigned 47 33056:10 00000000000ae0df [3,11,0] Successfully reassigned 48 33056:10 00000000000ae0e1 [3,11,0] Successfully reassigned 49 33056:11 00000000000ae0e3 [3,11,0] Successfully reassigned 50 33056:11 00000000000ae0e8 [3,11,0] Successfully reassigned 51 33056:11 00000000000ae0ec [3,11,0] Successfully reassigned 52 33056:13 00000000000ae0ee [3,11,0] Successfully reassigned 53 33056:13 00000000000ae0f0 [3,11,0] Successfully reassigned 54 33056:14 00000000000ae0f2 [3,11,0] Successfully reassigned 55 33056:14 00000000000ae0f4 [3,11,0] Successfully reassigned 56 33056:14 00000000000ae0f6 [3,11,0] Successfully reassigned 57 33056:14 00000000000ae0f7 [3,11,0] Successfully reassigned 58 33056:14 00000000000ae0f9 [3,11,0] Successfully reassigned 59 33056:15 00000000000ae0fb [3,11,0] Successfully reassigned 60 33056:15 00000000000ae0fd [3,11,0] Successfully reassigned 61 33056:15 00000000000ae0ff [1,17,2] Recovered via rewrite in-place 62 33056:15 00000000000ae170 [1,17,1] Recovered via rewrite in-place 63 33056:15 00000000000ae172 [1,18,1] Recovered via rewrite in-place 64 33056:15 00000000000ae1e5 [1,18,1] Recovered via rewrite in-place 65 33056:15 00000000000ae1e7 [1,18,1] Recovered via rewrite in-place 66 33056:15 00000000000ae61d [3,11,0] Successfully reassigned 67 33056:15 00000000000ae61f [3,11,0] Successfully reassigned 68 33056:15 00000000000ae621 [3,11,0] Successfully reassigned 69 33056:16 00000000000ae623 [3,11,0] Successfully reassigned 70 33056:16 00000000000ae625 [3,11,0] Successfully reassigned 71 33056:16 00000000000ae628 [1,17,1] Recovered via rewrite in-place 72 33056:16 00000000000ae62a [1,18,1] Recovered via rewrite in-place 73 33056:16 00000000000ae62b [1,17,2] Recovered via rewrite in-place 74 33056:16 00000000000ae62c [3,11,0] Successfully reassigned 75 33056:16 00000000000ae62e [3,11,0] Successfully reassigned 76 33056:16 00000000000ae630 [3,11,0] Successfully reassigned 77 33056:16 00000000000ae632 [3,11,0] Successfully reassigned 78 33056:16 00000000000ae634 [3,11,0] Successfully reassigned 79 33056:16 00000000000ae636 [3,11,0] Successfully reassigned 80 33056:17 00000000000ae638 [3,11,0] Successfully reassigned 81 33056:17 00000000000ae63a [3,11,0] Successfully reassigned 82 33056:18 00000000000ae63c [3,11,0] Successfully reassigned 83 33056:20 00000000000ae645 [3,11,0] Successfully reassigned 84 33056:20 00000000000ae647 [3,11,0] Successfully reassigned 85 33056:21 00000000000ae649 [3,11,0] Successfully reassigned 86 33056:22 00000000000ae64b [1,17,2] Recovered via rewrite in-place 87 33056:23 00000000000b009b [3,11,0] Successfully reassigned 88 33056:23 00000000000b009d [3,11,0] Successfully reassigned 89 33056:23 00000000000b009f [3,11,0] Successfully reassigned 90 33056:23 00000000000b00ac [1,17,2] Recovered via rewrite in-place 91 33056:24 00000000000b00ae [3,11,0] Successfully reassigned 92 33056:24 00000000000b00b0 [3,11,0] Successfully reassigned 93 33056:24 00000000000b00bd [3,11,0] Successfully reassigned 94 33056:24 00000000000b00bf [3,11,0] Successfully reassigned 95 33056:24 00000000000b00c1 [3,11,0] Successfully reassigned 96 33056:25 00000000000b00c5 [3,11,0] Successfully reassigned 97 33056:25 00000000000b00c7 [3,11,0] Successfully reassigned 98 33056:25 00000000000b0760 [3,11,0] Successfully reassigned 99 33056:25 00000000000b0762 [3,11,0] Successfully reassigned 100 33056:25 00000000000b0764 [3,11,0] Successfully reassigned 101 33056:25 00000000000b0766 [3,11,0] Successfully reassigned 102 33056:25 00000000000b0768 [3,11,0] Successfully reassigned 103 33056:25 00000000000b0769 [3,11,0] Successfully reassigned 104 33056:26 00000000000b076b [3,11,0] Successfully reassigned 105 33056:26 00000000000b076d [3,11,0] Successfully reassigned 106 33056:26 00000000000b076f [3,11,0] Successfully reassigned 107 33056:26 00000000000b0771 [3,11,0] Successfully reassigned 108 33056:26 00000000000b0773 [3,11,0] Successfully reassigned 109 33056:26 00000000000b0775 [3,11,0] Successfully reassigned 110 33056:27 00000000000b8327 [3,11,0] Successfully reassigned 111 33056:28 00000000000b8328 [3,11,0] Successfully reassigned 112 33056:29 00000000000b832a [3,11,0] Successfully reassigned 113 33056:29 00000000000b832b [1,17,2] Recovered via rewrite in-place 114 33056:29 00000000000b832c [3,11,0] Successfully reassigned 115 33056:29 00000000000b832e [3,11,0] Successfully reassigned 116 33056:29 00000000000b8330 [3,11,0] Successfully reassigned 117 33056:30 00000000000b8332 [3,11,0] Successfully reassigned 118 33056:30 00000000000b90af [3,11,0] Successfully reassigned 119 33056:30 00000000000b90b8 [3,11,0] Successfully reassigned 120 33056:30 00000000000b9735 [1,17,1] Recovered via rewrite in-place 121 33095:58 0000000001b9afe2 [3,11,0] Successfully reassigned 122 33103:57 00000000000ae176 [1,17,2] Successfully reassigned 123 33127:53 00000000000ae59e [1,17,2] Recovered via rewrite in-place 124 33199:42 00000000000b9728 [1,17,2] Recovered via rewrite in-place 125 33391:19 00000000000ae086 [1,17,2] Recovered via rewrite in-place 126 33391:19 00000000000b00b7 [1,17,1] Successfully reassigned 127 33415:15 00000000000b972e [1,17,2] Successfully reassigned 128 35256:25 00000000433a4bee [1,17,1] Recovered via rewrite in-place 129 35256:25 00000000433a4bef [1,17,1] Recovered via rewrite in-place 130 35256:25 00000000433a4bf2 [1,17,3] Recovered via rewrite in-place 131 35256:25 00000000433a4bf6 [1,17,1] Recovered via rewrite in-place 132 35256:25 00000000433a4c09 [1,17,3] Recovered via rewrite in-place 133 35256:25 00000000433a4c0a [1,17,1] Recovered via rewrite in-place 134 35429:45 00000000433a4bed [1,17,1] Recovered via rewrite in-place 135 37564:35 000000001027f619 [1,17,1] Recovered via rewrite in-place 136 39765:22 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 137 40435:05 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 138 41927:37 000000001027f619 [1,17,1] Recovered via rewrite in-place 139 41972:09 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 140 42149:26 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 141 42191:53 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 142 42955:10 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 143 43738:54 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 144 43913:28 000000001027f619 [1,17,1] Recovered via rewrite in-place 145 44280:04 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 146 44325:55 000000001027f618 [1,17,1] Recovered via rewrite in-place 147 44397:40 000000003e62eb4c [1,17,1] Recovered via rewrite in-place 148 44745:56 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 149 44745:56 000000001027f619 [1,17,1] Recovered via rewrite in-place 150 45057:14 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 151 45493:20 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 152 45493:20 000000001027e9ea [1,17,1] Recovered via rewrite in-place 153 46105:56 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 154 46105:56 000000001027f619 [1,17,1] Recovered via rewrite in-place 155 46117:28 000000001027f618 [1,17,1] Recovered via rewrite in-place 156 46457:01 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 157 46627:21 000000003100a2b1 [1,17,1] Recovered via rewrite in-place 158 46627:21 000000003100a2b2 [1,17,1] Recovered via rewrite in-place 159 46627:21 000000003100a2b3 [1,17,1] Recovered via rewrite in-place 160 46643:52 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 161 46765:26 000000001027f619 [1,17,1] Recovered via rewrite in-place 162 46831:26 0000000032b7a8c4 [1,17,1] Recovered via rewrite in-place 163 46844:04 0000000030de8927 [1,17,1] Recovered via rewrite in-place 164 46985:55 000000003e62eb45 [1,17,1] Recovered via rewrite in-place 165 47109:47 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 166 47625:26 000000001027f619 [1,17,1] Recovered via rewrite in-place 167 47827:53 000000003100a26b [1,17,1] Recovered via rewrite in-place 168 47876:04 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 169 47876:04 000000001027f618 [1,17,1] Recovered via rewrite in-place 170 48504:07 000000001027f619 [1,17,1] Recovered via rewrite in-place 171 48534:42 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 172 48841:25 000000001027f618 [1,17,1] Recovered via rewrite in-place 173 49180:31 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 174 49180:31 000000001027f619 [1,17,1] Recovered via rewrite in-place 175 49215:58 000000003e5fe166 [1,17,1] Recovered via rewrite in-place 176 49554:38 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 177 49754:43 000000003e62eb46 [1,17,1] Recovered via rewrite in-place 178 49951:28 000000001027f619 [1,17,1] Recovered via rewrite in-place 179 49984:15 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 180 50184:03 000000001027f618 [1,17,1] Recovered via rewrite in-place 181 50220:34 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 182 50533:50 000000001027e9e9 [1,17,2] Recovered via rewrite in-place 183 50955:15 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 184 50977:04 0000000032a5f3f9 [1,17,1] Recovered via rewrite in-place 185 51176:45 00000000323d1d26 [1,17,1] Recovered via rewrite in-place 186 51295:49 0000000032b7a8c6 [1,17,1] Recovered via rewrite in-place 187 51295:49 0000000032b7a8c7 [1,17,1] Recovered via rewrite in-place 188 51418:08 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 189 51418:08 000000001027e9ea [1,17,1] Recovered via rewrite in-place 190 51418:08 000000001027f619 [1,17,1] Recovered via rewrite in-place 191 51528:50 0000000032a5f3f8 [1,17,1] Recovered via rewrite in-place 192 51583:07 0000000030de8929 [1,17,1] Recovered via rewrite in-place 193 51790:28 000000003e62eb47 [1,17,1] Recovered via rewrite in-place 194 52100:05 000000001027f618 [1,17,1] Recovered via rewrite in-place 195 52435:03 0000000032a5f3f7 [1,17,1] Recovered via rewrite in-place 196 52619:52 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 197 52619:52 000000001027f619 [1,17,1] Recovered via rewrite in-place 198 52650:00 0000000032b7a8c4 [1,17,1] Recovered via rewrite in-place 199 53722:34 000000001027f618 [1,17,1] Recovered via rewrite in-place 200 53722:34 000000001027f619 [1,17,1] Recovered via rewrite in-place 201 53985:27 0000000030de892c [1,17,1] Recovered via rewrite in-place 202 54544:38 0000000030de8928 [1,17,1] Recovered via rewrite in-place 203 54602:41 0000000032b7a8cb [1,17,1] Recovered via rewrite in-place 204 54602:41 0000000032b7a8cc [1,17,1] Recovered via rewrite in-place 205 54647:58 0000000032b7a8c3 [1,17,1] Recovered via rewrite in-place 206 54647:58 0000000032b7a8c9 [1,17,1] Recovered via rewrite in-place 207 54999:25 000000001027e9e9 [1,17,2] Recovered via rewrite in-place 208 54999:25 000000001027f619 [1,17,3] Recovered via rewrite in-place 209 55342:36 000000003100a25e [1,17,1] Recovered via rewrite in-place 210 55443:14 00000000323d1d2a [1,17,1] Recovered via rewrite in-place 211 55573:45 000000003322f481 [1,17,1] Recovered via rewrite in-place 212 55872:19 000000001027f619 [1,17,1] Recovered via rewrite in-place 213 56043:54 00000000323df046 [1,17,1] Recovered via rewrite in-place 214 56086:19 000000003322f482 [1,17,1] Recovered via rewrite in-place 215 56380:48 00000000323df045 [1,17,1] Recovered via rewrite in-place 216 56640:22 00000000323df041 [1,17,1] Recovered via rewrite in-place 217 56654:31 0000000030de8927 [1,17,1] Recovered via rewrite in-place 218 56654:31 0000000030de8928 [1,17,1] Recovered via rewrite in-place 219 56654:31 0000000030de892a [1,17,1] Recovered via rewrite in-place 220 56749:44 000000001027e9e9 [1,17,2] Recovered via rewrite in-place 221 56749:44 000000001027f618 [1,17,1] Recovered via rewrite in-place 222 56749:44 000000001027f619 [1,17,1] Recovered via rewrite in-place 223 63262:13 00000000000254c9 [1,17,1] Recovered via rewrite in-place 224 63492:59 00000000087d781e [1,17,1] Recovered via rewrite in-place 225 63492:59 00000000087d781f [1,17,1] Recovered via rewrite in-place 226 63522:54 00000000000254c8 [1,17,1] Recovered via rewrite in-place 227 63649:31 00000000000254ca [1,17,1] Recovered via rewrite in-place 228 63655:33 0000000018ab5ae9 [1,17,1] Recovered via rewrite in-place 229 64158:40 00000000042ab1a8 [1,17,1] Recovered via rewrite in-place 230 64490:31 00000000087afb75 [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c5003b8d8eed attached SAS address = 0x500056b3b2546dff attached phy identifier = 6 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 1.5 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5003b8d8eee attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,megaraid_disk_07 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST31000528AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC38 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:08 2024 +05 ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213891en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. Warning: This result is based on an Attribute check. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 173) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 099 006 - 65687095 3 Spin_Up_Time PO---- 094 092 000 - 0 4 Start_Stop_Count -O--CK 091 091 020 - 9726 5 Reallocated_Sector_Ct PO--CK 002 002 036 NOW 4015 7 Seek_Error_Rate POSR-- 061 060 030 - 1318954260943 9 Power_On_Hours -O--CK 071 071 000 - 25717 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4520 183 Runtime_Bad_Block -O--CK 082 082 000 - 18 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 091 000 - 107375886407 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 078 051 045 - 22 (Min/Max 21/23) 194 Temperature_Celsius -O---K 022 049 000 - 22 (255 254 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 018 016 000 - 65687095 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 36303 (24 160 0) 241 Total_LBAs_Written ------ 100 253 000 - 3743902899 242 Total_LBAs_Read ------ 100 253 000 - 4234266849 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 21/23 Celsius Lifetime Min/Max Temperature: -2/49 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sda,megaraid_disk_08 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 (CMR) Device Model: ST1000DM010-2EP102 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC43 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:08 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 108) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 063 006 - 1176836 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 65 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 084 060 045 - 248750298 9 Power_On_Hours -O--CK 082 082 000 - 15934 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 58 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 083 054 040 - 17 (Min/Max 16/21) 193 Load_Cycle_Count -O--CK 100 100 000 - 709 194 Temperature_Celsius -O---K 017 015 000 - 17 (0 15 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 100 001 000 - 1176836 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 15856h+04m+45.670s 241 Total_LBAs_Written ------ 100 253 000 - 13847177004 242 Total_LBAs_Read ------ 100 253 000 - 9110076841 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4120 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 4800 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 17 Celsius Power Cycle Min/Max Temperature: 16/21 Celsius Lifetime Min/Max Temperature: 15/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 58 --- Lifetime Power-On Resets 0x01 0x010 4 15934 --- Power-on Hours 0x01 0x018 6 13847574178 --- Logical Sectors Written 0x01 0x020 6 386140105 --- Number of Write Commands 0x01 0x028 6 9116981665 --- Logical Sectors Read 0x01 0x030 6 171180761 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 9028 --- Spindle Motor Power-on Hours 0x03 0x010 4 370 --- Head Flying Hours 0x03 0x018 4 709 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 17 --- Current Temperature 0x05 0x010 1 18 --- Average Short Term Temperature 0x05 0x018 1 17 --- Average Long Term Temperature 0x05 0x020 1 47 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 45 --- Highest Average Short Term Temperature 0x05 0x038 1 17 --- Lowest Average Short Term Temperature 0x05 0x040 1 42 --- Highest Average Long Term Temperature 0x05 0x048 1 17 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 13 --- Specified Minimum Operating Temperature |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sda,megaraid_disk_09 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Re Device Model: WDC WD2000FYYZ-01UL1B2 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01K03 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:08 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (25620) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 279) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 206 171 021 - 4675 4 Start_Stop_Count -O--CK 100 100 000 - 50 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 040 040 000 - 44275 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 50 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 48 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 128 110 000 - 22 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 35437 hours (1476 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 e4 6a 7d 40 00 Error: UNC at LBA = 0x00e46a7d = 14969469 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 02 00 00 08 00 00 00 e4 6a 00 40 00 21:45:17.467 READ FPDMA QUEUED 60 02 00 00 00 00 00 00 e4 68 00 40 00 21:45:17.464 READ FPDMA QUEUED 60 02 00 00 f8 00 00 00 e4 66 00 40 00 21:45:17.460 READ FPDMA QUEUED 60 02 00 00 f0 00 00 00 e4 64 00 40 00 21:45:17.454 READ FPDMA QUEUED 60 02 00 00 e8 00 00 00 e4 62 00 40 00 21:45:17.451 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 31939 hours (1330 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 e4 6a 73 40 00 Error: UNC at LBA = 0x00e46a73 = 14969459 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 02 00 00 f0 00 00 00 e4 6a 00 40 00 4d+06:21:35.535 READ FPDMA QUEUED 60 02 00 00 e8 00 00 00 e4 68 00 40 00 4d+06:21:35.531 READ FPDMA QUEUED 60 02 00 00 e0 00 00 00 e4 66 00 40 00 4d+06:21:35.528 READ FPDMA QUEUED 60 02 00 00 d8 00 00 00 e4 64 00 40 00 4d+06:21:35.522 READ FPDMA QUEUED 60 02 00 00 d0 00 00 00 e4 62 00 40 00 4d+06:21:35.518 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 20/23 Celsius Lifetime Min/Max Temperature: 9/40 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 225170 Vendor specific /dev/sda,megaraid_disk_10 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Re Device Model: WDC WD2000FYYZ-01UL1B2 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01K03 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:08 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (25920) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 282) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 188 170 021 - 5558 4 Start_Stop_Count -O--CK 100 100 000 - 59 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 040 040 000 - 44467 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 59 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 57 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 128 106 000 - 22 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 19/23 Celsius Lifetime Min/Max Temperature: 10/44 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 225216 Vendor specific /dev/sda,megaraid_disk_12 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Kingston SSDNow UV400/500 Device Model: KINGSTON SUV400S37240G Serial Number: -- LU WWN Device Id: 0 550380 ... Firmware Version: 0C3G37R5 User Capacity: 240,057,409,536 bytes [240 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5319 ATA Version is: ACS-4, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:08 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 5) minutes. Conveyance self-test routine recommended polling time: ( 0) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 48 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 105000293 5 Reallocated_Sector_Ct PO--CK 096 096 010 - 37 9 Power_On_Hours -O--CK 100 100 000 - 37542 12 Power_Cycle_Count -O--CK 100 100 000 - 8864 100 Unknown_Kingston_Attr -O--CK 100 100 000 - 180328640 101 Unknown_Kingston_Attr -O--CK 100 100 000 - 3533024 170 Reserved_Block_Count -O--CK 100 100 000 - 37 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 43 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 000 - 0 177 Wear_Leveling_Count -O--CK 134 000 000 - 79932 178 Used_Rsvd_Blk_Cnt_Chip -O---- 100 100 000 - 6 180 Unused_Rsvd_Blk_Cnt_Tot -O---- 100 100 000 - 770 183 Runtime_Bad_Block -O--CK 074 074 000 - 120 187 Reported_Uncorrect PO--CK 100 100 000 - 23978 194 Temperature_Celsius -O---K 027 100 000 - 27 (Min/Max 16/50) 195 Hardware_ECC_Recovered -O--CK 100 100 000 - 105000293 196 Reallocated_Event_Count -O--CK 100 100 000 - 37 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--C- 100 100 000 - 0 201 Unc_Read_Error_Rate -O--CK 100 100 000 - 0 204 Soft_ECC_Correction -O--CK 100 100 000 - 104976315 231 SSD_Life_Left -O--CK 000 000 000 - 100 233 Media_Wearout_Indicator -O--CK 100 100 000 - 462076 234 Unknown_Attribute -O--CK 100 100 000 - 31029 241 Host_Writes_GiB -O--CK 100 100 000 - 57742 242 Host_Reads_GiB -O--CK 100 100 000 - 90408 250 Read_Retry_Count -O--CK 100 100 000 - 716606443 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 5 Device Statistics Notification 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 9 Device vendor specific log 0xab SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 0 (1 sectors) Device Error Count: 1258 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1258 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 01 71 b3 fb e1 08 Error: UNC 5 sectors at LBA = 0x0171b3fb = 24228859 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 05 00 00 01 71 b3 fb e1 08 00:07:13.434 READ DMA Error 1257 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 71 b3 fa e1 08 Error: UNC 1 sectors at LBA = 0x0171b3fa = 24228858 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 01 00 00 01 71 b3 fa e1 08 00:07:13.402 READ DMA Error 1256 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 01 71 b3 f8 e1 08 Error: UNC 2 sectors at LBA = 0x0171b3f8 = 24228856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 02 00 00 01 71 b3 f8 e1 08 00:07:13.370 READ DMA Error 1255 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 01 71 b3 fc e1 08 Error: UNC 4 sectors at LBA = 0x0171b3fc = 24228860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 04 00 00 01 71 b3 fc e1 08 00:07:13.338 READ DMA SMART Extended Self-test Log Version: 0 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 24/29 Celsius Lifetime Min/Max Temperature: 16/50 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 8864 --- Lifetime Power-On Resets 0x01 0x010 4 37542 --- Power-on Hours 0x01 0x018 6 121094098990 --- Logical Sectors Written 0x01 0x020 6 1698224350 --- Number of Write Commands 0x01 0x028 6 189600064841 --- Logical Sectors Read 0x01 0x030 6 1636624910 --- Number of Read Commands 0x01 0x038 6 135152941200 --- Date and Time TimeStamp 0x02 ===== = = === == Free-Fall Statistics (empty) == 0x03 ===== = = === == Rotating Media Statistics (empty) == 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 23978 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 679 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 28 -D- Current Temperature 0x05 0x010 1 - -D- Average Short Term Temperature 0x05 0x018 1 0 -D- Average Long Term Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 27 -D- Highest Average Short Term Temperature 0x05 0x038 1 23 -D- Lowest Average Short Term Temperature 0x05 0x040 1 - -D- Highest Average Long Term Temperature 0x05 0x048 1 - -D- Lowest Average Long Term Temperature 0x05 0x050 4 0 -D- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 -D- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 679 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 100 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET /dev/sda,megaraid_disk_13 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7E (AF) Device Model: SAMSUNG HM321HI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AJ10001 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:09 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. Warning: This result is based on an Attribute check. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 137) The previous self-test completed having a test element that failed and the device is suspected of having handling damage. Total time to complete Offline data collection: ( 4920) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 82) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 001 001 051 NOW 37634 2 Throughput_Performance POS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 093 091 025 - 2137 4 Start_Stop_Count -O--CK 095 095 000 - 5162 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-K 252 252 051 - 0 8 Seek_Time_Performance P-S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 19675 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 098 098 000 - 2748 12 Power_Cycle_Count -O--CK 095 095 000 - 5431 183 Runtime_Bad_Block -O--CK 252 252 010 - 0 184 End-to-End_Error PO--CK 252 252 048 - 0 186 Unknown_Attribute -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 37436 188 Command_Timeout -O--CK 252 252 000 - 0 190 Airflow_Temperature_Cel -O---- 077 043 040 - 23 (Min/Max 11/60) 191 G-Sense_Error_Rate -O---K 098 098 000 - 29220 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 193 Load_Cycle_Count -O--CK 064 064 000 - 366185 194 Temperature_Celsius -O---- 064 043 000 - 23 (Min/Max 11/60) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 2 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 1 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 9755 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 37437 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 37437 [4] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 10 00 08 00 00 0c b2 3e f0 40 08 00:00:14.989 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.989 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.989 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.989 SET FEATURES [Set transfer mode] Error 37436 [3] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 10 00 08 00 00 0c b2 3e f0 40 08 00:00:14.986 READ FPDMA QUEUED 61 00 10 00 30 00 00 03 49 52 f6 40 08 00:00:14.986 WRITE FPDMA QUEUED 61 00 10 00 58 00 00 03 49 52 96 40 08 00:00:14.986 WRITE FPDMA QUEUED 61 00 10 00 50 00 00 03 49 52 3e 40 08 00:00:14.986 WRITE FPDMA QUEUED Error 37435 [2] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 10 00 08 00 00 0c b2 3e f0 40 08 00:00:14.984 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.984 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.984 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.984 SET FEATURES [Set transfer mode] Error 37434 [1] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.982 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:14.978 FLUSH CACHE EXT 61 00 00 00 08 00 00 02 4d ea e6 40 08 00:00:14.978 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:14.978 FLUSH CACHE EXT Error 37433 [0] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.940 READ FPDMA QUEUED 60 00 10 00 08 00 00 05 64 a8 a8 40 08 00:00:14.953 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.953 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.953 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.953 SET FEATURES [Set transfer mode] Error 37432 [7] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.935 READ FPDMA QUEUED 60 00 10 00 08 00 00 05 64 a8 a8 40 08 00:00:14.951 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.951 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.951 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.951 SET FEATURES [Set transfer mode] Error 37431 [6] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.935 READ FPDMA QUEUED 60 00 10 00 08 00 00 05 64 a8 a8 40 08 00:00:14.948 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.948 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.948 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.948 SET FEATURES [Set transfer mode] Error 37430 [5] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.930 READ FPDMA QUEUED 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.946 READ FPDMA QUEUED 61 00 00 03 50 00 00 04 0d fa f6 40 08 00:00:14.946 WRITE FPDMA QUEUED 61 00 00 05 c8 00 00 04 0d f5 2e 40 08 00:00:14.946 WRITE FPDMA QUEUED 61 00 00 08 90 00 00 04 0d ec 9e 40 08 00:00:14.946 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: handling damage?? 90% 13782 0 # 2 Short offline Completed: handling damage?? 90% 13781 0 # 3 Short offline Completed: handling damage?? 90% 13780 0 SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed_handling_damage?? [90% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 22/24 Celsius Lifetime Min/Max Temperature: 16/63 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdc,megaraid_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital RE3 Serial ATA Device Model: WD2502ABYS-23B7A0 39M4511 42C0463IBM Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.03B07 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:10 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4680) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 58) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 200 199 021 - 975 4 Start_Stop_Count -O--CK 100 100 000 - 115 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 005 005 000 - 70011 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 114 192 Power-Off_Retract_Count -O--CK 200 200 000 - 112 193 Load_Cycle_Count -O--CK 200 200 000 - 2 194 Temperature_Celsius -O---K 123 103 000 - 20 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 20 Celsius Power Cycle Min/Max Temperature: 17/22 Celsius Lifetime Min/Max Temperature: 19/40 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x8000 4 225224 Vendor specific /dev/sdc,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital RE3 Serial ATA Device Model: WD2502ABYS-23B7A0 39M4511 42C0463IBM Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.03B07 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:10 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4680) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 58) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 200 199 021 - 991 4 Start_Stop_Count -O--CK 100 100 000 - 73 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 020 020 000 - 58642 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 72 192 Power-Off_Retract_Count -O--CK 200 200 000 - 57 193 Load_Cycle_Count -O--CK 200 200 000 - 15 194 Temperature_Celsius -O---K 124 101 000 - 19 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 36656 hours (1527 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 13 34 00 f0 00 40 00 Error: IDNF at LBA = 0x133400f000 = 82476855296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 05 00 00 b0 00 00 13 f0 34 00 40 08 00:11:51.129 WRITE FPDMA QUEUED 61 04 80 00 a8 00 00 13 f0 2f 80 40 08 00:11:51.121 WRITE FPDMA QUEUED 61 02 80 00 a0 00 00 13 f0 2d 00 40 08 00:11:51.115 WRITE FPDMA QUEUED 61 08 80 00 98 00 00 13 f0 24 80 40 08 00:11:51.110 WRITE FPDMA QUEUED 61 05 00 00 90 00 00 13 f0 1f 80 40 08 00:11:51.098 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 17 Celsius Power Cycle Min/Max Temperature: 16/21 Celsius Lifetime Min/Max Temperature: 17/42 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x8000 4 225224 Vendor specific /dev/sdc,megaraid_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: MG04ACA200N 00YK039D7A01888LEN Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: TK44 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:10 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 232) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 3283 4 Start_Stop_Count -O--CK 100 100 000 - 206 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 083 083 000 - 7124 10 Spin_Retry_Count PO--CK 104 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 206 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 001 - 0 190 Airflow_Temperature_Cel -O---K 081 061 045 - 19 (Min/Max 17/20) 192 Power-Off_Retract_Count -O--CK 100 100 000 - 203 193 Load_Cycle_Count -O--CK 100 100 000 - 206 194 Temperature_Celsius -O---K 100 100 000 - 19 (Min/Max 15/39) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 253 000 - 0 212 Unknown_Attribute -O--CK 100 100 000 - 0 220 Disk_Shift -O---- 100 100 000 - 0 222 Loaded_Hours -O--CK 083 083 000 - 7121 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 546 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 12288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa7 GPL VS 8 Device vendor specific log 0xa8 GPL VS 7681 Device vendor specific log 0xb0 GPL,SL VS 1 Device vendor specific log 0xb1 GPL VS 12288 Device vendor specific log 0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 19 Celsius Power Cycle Min/Max Temperature: 17/20 Celsius Lifetime Min/Max Temperature: 15/39 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 206 --- Lifetime Power-On Resets 0x01 0x010 4 7124 --- Power-on Hours 0x01 0x018 6 307803767 --- Logical Sectors Written 0x01 0x020 6 986203 --- Number of Write Commands 0x01 0x028 6 27330621177 --- Logical Sectors Read 0x01 0x030 6 213540848 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 0 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 7121 --- Spindle Motor Power-on Hours 0x03 0x010 4 7121 --- Head Flying Hours 0x03 0x018 4 206 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 19 --- Current Temperature 0x05 0x010 1 18 N-- Average Short Term Temperature 0x05 0x018 1 16 N-- Average Long Term Temperature 0x05 0x020 1 39 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x030 1 27 N-- Highest Average Short Term Temperature 0x05 0x038 1 15 N-- Lowest Average Short Term Temperature 0x05 0x040 1 22 N-- Highest Average Long Term Temperature 0x05 0x048 1 16 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 44896 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc,megaraid_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Purple Device Model: WDC WD40PURX-64GVNY0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:12 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (51840) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 518) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 171 171 021 - 8450 4 Start_Stop_Count -O--CK 100 100 000 - 318 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 077 077 000 - 17240 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 79 192 Power-Off_Retract_Count -O--CK 200 200 000 - 61 193 Load_Cycle_Count -O--CK 200 200 000 - 355 194 Temperature_Celsius -O---K 133 105 000 - 19 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 39 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 6041 hours (251 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 01 aa ad fc c0 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 3d+04:19:17.645 FLUSH CACHE EXT 61 00 08 00 50 00 00 00 5c 64 70 40 00 3d+03:59:18.124 WRITE FPDMA QUEUED 61 00 08 00 48 00 00 00 5c 64 80 40 00 3d+03:59:18.123 WRITE FPDMA QUEUED 61 00 08 00 40 00 00 00 64 75 58 40 00 3d+03:59:13.028 WRITE FPDMA QUEUED 61 00 08 00 38 00 00 00 5c 64 78 40 00 3d+03:59:07.834 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 19 Celsius Power Cycle Min/Max Temperature: 17/20 Celsius Lifetime Min/Max Temperature: 16/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 225242 Vendor specific /dev/sdc,megaraid_disk_06 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST3600057SS Revision: 0008 Compliance: SPC-3 User Capacity: 600,127,266,816 bytes [600 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5003b8d8eef Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Dec 5 12:18:12 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 68 C Elements in grown defect list: 668 Vendor (Seagate Cache) information Blocks sent to initiator = 1438821285 Blocks received from initiator = 4292434641 Blocks read from cache and sent to initiator = 2949839783 Number of read and write commands whose size <= segment size = 2302975697 Number of read and write commands whose size > segment size = 0 Vendor (Seagate/Hitachi) factory information number of hours powered up = 65023.22 number of minutes until next internal SMART test = 25 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 1168962932 168 0 1168963100 1168963378 145872.211 278 write: 0 0 1 1 7 41996.684 1 verify: 137 0 0 137 144 0.000 3 Non-medium error count: 345 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 65023:13 [3901393 minutes] Number of background scans performed: 979, scan progress: 0.00% Number of background medium scans performed: 62171 # when lba(hex) [sk,asc,ascq] reassign_status 1 12968:43 0000000042e0b46c [1,18,1] Recovered via rewrite in-place 2 13000:52 0000000042e0b87e [3,11,0] Recovered via rewrite in-place 3 13000:52 0000000042e0b87f [3,11,0] Recovered via rewrite in-place 4 13000:52 0000000042e0bc90 [3,11,0] Recovered via rewrite in-place 5 13000:52 0000000042e0bc91 [3,11,0] Recovered via rewrite in-place 6 13000:52 0000000042e0bc92 [3,11,0] Recovered via rewrite in-place 7 13000:52 0000000042e0c0a3 [3,11,0] Recovered via rewrite in-place 8 13000:52 0000000042e0c4b5 [3,11,0] Recovered via rewrite in-place 9 13000:53 00000000436604ac [3,11,0] Recovered via rewrite in-place 10 13000:55 0000000044373d96 [1,17,3] Recovered via rewrite in-place 11 13000:55 0000000044373d97 [3,11,0] Recovered via rewrite in-place 12 13000:55 0000000044373d98 [3,11,0] Recovered via rewrite in-place 13 13000:55 000000004450bbca [3,11,0] Recovered via rewrite in-place 14 29816:10 00000000000abfb1 [1,18,1] Successfully reassigned 15 31418:07 00000000000ad314 [1,18,1] Successfully reassigned 16 31418:08 00000000000bbcf3 [1,17,2] Recovered via rewrite in-place 17 31513:53 00000000000accae [1,17,2] Successfully reassigned 18 31537:53 00000000000bb718 [1,17,3] Successfully reassigned 19 32304:11 00000000000af856 [1,17,3] Successfully reassigned 20 32661:48 000000003100a258 [1,17,1] Recovered via rewrite in-place 21 33056:00 00000000000ac1f5 [1,17,3] Successfully reassigned 22 33056:01 00000000000ae079 [3,11,0] Recovered via rewrite in-place 23 33056:02 00000000000ae07b [3,11,0] Successfully reassigned 24 33056:02 00000000000ae07d [3,11,0] Successfully reassigned 25 33056:02 00000000000ae07f [3,11,0] Successfully reassigned 26 33056:03 00000000000ae080 [3,11,0] Successfully reassigned 27 33056:03 00000000000ae081 [3,11,0] Successfully reassigned 28 33056:04 00000000000ae082 [3,11,0] Successfully reassigned 29 33056:04 00000000000ae09c [3,11,0] Successfully reassigned 30 33056:04 00000000000ae0ba [3,11,0] Successfully reassigned 31 33056:04 00000000000ae0bc [3,11,0] Successfully reassigned 32 33056:04 00000000000ae0be [3,11,0] Successfully reassigned 33 33056:05 00000000000ae0c1 [3,11,0] Successfully reassigned 34 33056:05 00000000000ae0c3 [3,11,0] Successfully reassigned 35 33056:05 00000000000ae0c5 [3,11,0] Successfully reassigned 36 33056:05 00000000000ae0c7 [3,11,0] Successfully reassigned 37 33056:05 00000000000ae0c9 [3,11,0] Successfully reassigned 38 33056:06 00000000000ae0cb [3,11,0] Successfully reassigned 39 33056:06 00000000000ae0cc [3,11,0] Successfully reassigned 40 33056:07 00000000000ae0ce [3,11,0] Successfully reassigned 41 33056:08 00000000000ae0d0 [3,11,0] Successfully reassigned 42 33056:10 00000000000ae0d6 [3,11,0] Successfully reassigned 43 33056:10 00000000000ae0d8 [1,17,2] Recovered via rewrite in-place 44 33056:10 00000000000ae0d9 [3,11,0] Successfully reassigned 45 33056:10 00000000000ae0db [3,11,0] Successfully reassigned 46 33056:10 00000000000ae0dd [3,11,0] Successfully reassigned 47 33056:10 00000000000ae0df [3,11,0] Successfully reassigned 48 33056:10 00000000000ae0e1 [3,11,0] Successfully reassigned 49 33056:11 00000000000ae0e3 [3,11,0] Successfully reassigned 50 33056:11 00000000000ae0e8 [3,11,0] Successfully reassigned 51 33056:11 00000000000ae0ec [3,11,0] Successfully reassigned 52 33056:13 00000000000ae0ee [3,11,0] Successfully reassigned 53 33056:13 00000000000ae0f0 [3,11,0] Successfully reassigned 54 33056:14 00000000000ae0f2 [3,11,0] Successfully reassigned 55 33056:14 00000000000ae0f4 [3,11,0] Successfully reassigned 56 33056:14 00000000000ae0f6 [3,11,0] Successfully reassigned 57 33056:14 00000000000ae0f7 [3,11,0] Successfully reassigned 58 33056:14 00000000000ae0f9 [3,11,0] Successfully reassigned 59 33056:15 00000000000ae0fb [3,11,0] Successfully reassigned 60 33056:15 00000000000ae0fd [3,11,0] Successfully reassigned 61 33056:15 00000000000ae0ff [1,17,2] Recovered via rewrite in-place 62 33056:15 00000000000ae170 [1,17,1] Recovered via rewrite in-place 63 33056:15 00000000000ae172 [1,18,1] Recovered via rewrite in-place 64 33056:15 00000000000ae1e5 [1,18,1] Recovered via rewrite in-place 65 33056:15 00000000000ae1e7 [1,18,1] Recovered via rewrite in-place 66 33056:15 00000000000ae61d [3,11,0] Successfully reassigned 67 33056:15 00000000000ae61f [3,11,0] Successfully reassigned 68 33056:15 00000000000ae621 [3,11,0] Successfully reassigned 69 33056:16 00000000000ae623 [3,11,0] Successfully reassigned 70 33056:16 00000000000ae625 [3,11,0] Successfully reassigned 71 33056:16 00000000000ae628 [1,17,1] Recovered via rewrite in-place 72 33056:16 00000000000ae62a [1,18,1] Recovered via rewrite in-place 73 33056:16 00000000000ae62b [1,17,2] Recovered via rewrite in-place 74 33056:16 00000000000ae62c [3,11,0] Successfully reassigned 75 33056:16 00000000000ae62e [3,11,0] Successfully reassigned 76 33056:16 00000000000ae630 [3,11,0] Successfully reassigned 77 33056:16 00000000000ae632 [3,11,0] Successfully reassigned 78 33056:16 00000000000ae634 [3,11,0] Successfully reassigned 79 33056:16 00000000000ae636 [3,11,0] Successfully reassigned 80 33056:17 00000000000ae638 [3,11,0] Successfully reassigned 81 33056:17 00000000000ae63a [3,11,0] Successfully reassigned 82 33056:18 00000000000ae63c [3,11,0] Successfully reassigned 83 33056:20 00000000000ae645 [3,11,0] Successfully reassigned 84 33056:20 00000000000ae647 [3,11,0] Successfully reassigned 85 33056:21 00000000000ae649 [3,11,0] Successfully reassigned 86 33056:22 00000000000ae64b [1,17,2] Recovered via rewrite in-place 87 33056:23 00000000000b009b [3,11,0] Successfully reassigned 88 33056:23 00000000000b009d [3,11,0] Successfully reassigned 89 33056:23 00000000000b009f [3,11,0] Successfully reassigned 90 33056:23 00000000000b00ac [1,17,2] Recovered via rewrite in-place 91 33056:24 00000000000b00ae [3,11,0] Successfully reassigned 92 33056:24 00000000000b00b0 [3,11,0] Successfully reassigned 93 33056:24 00000000000b00bd [3,11,0] Successfully reassigned 94 33056:24 00000000000b00bf [3,11,0] Successfully reassigned 95 33056:24 00000000000b00c1 [3,11,0] Successfully reassigned 96 33056:25 00000000000b00c5 [3,11,0] Successfully reassigned 97 33056:25 00000000000b00c7 [3,11,0] Successfully reassigned 98 33056:25 00000000000b0760 [3,11,0] Successfully reassigned 99 33056:25 00000000000b0762 [3,11,0] Successfully reassigned 100 33056:25 00000000000b0764 [3,11,0] Successfully reassigned 101 33056:25 00000000000b0766 [3,11,0] Successfully reassigned 102 33056:25 00000000000b0768 [3,11,0] Successfully reassigned 103 33056:25 00000000000b0769 [3,11,0] Successfully reassigned 104 33056:26 00000000000b076b [3,11,0] Successfully reassigned 105 33056:26 00000000000b076d [3,11,0] Successfully reassigned 106 33056:26 00000000000b076f [3,11,0] Successfully reassigned 107 33056:26 00000000000b0771 [3,11,0] Successfully reassigned 108 33056:26 00000000000b0773 [3,11,0] Successfully reassigned 109 33056:26 00000000000b0775 [3,11,0] Successfully reassigned 110 33056:27 00000000000b8327 [3,11,0] Successfully reassigned 111 33056:28 00000000000b8328 [3,11,0] Successfully reassigned 112 33056:29 00000000000b832a [3,11,0] Successfully reassigned 113 33056:29 00000000000b832b [1,17,2] Recovered via rewrite in-place 114 33056:29 00000000000b832c [3,11,0] Successfully reassigned 115 33056:29 00000000000b832e [3,11,0] Successfully reassigned 116 33056:29 00000000000b8330 [3,11,0] Successfully reassigned 117 33056:30 00000000000b8332 [3,11,0] Successfully reassigned 118 33056:30 00000000000b90af [3,11,0] Successfully reassigned 119 33056:30 00000000000b90b8 [3,11,0] Successfully reassigned 120 33056:30 00000000000b9735 [1,17,1] Recovered via rewrite in-place 121 33095:58 0000000001b9afe2 [3,11,0] Successfully reassigned 122 33103:57 00000000000ae176 [1,17,2] Successfully reassigned 123 33127:53 00000000000ae59e [1,17,2] Recovered via rewrite in-place 124 33199:42 00000000000b9728 [1,17,2] Recovered via rewrite in-place 125 33391:19 00000000000ae086 [1,17,2] Recovered via rewrite in-place 126 33391:19 00000000000b00b7 [1,17,1] Successfully reassigned 127 33415:15 00000000000b972e [1,17,2] Successfully reassigned 128 35256:25 00000000433a4bee [1,17,1] Recovered via rewrite in-place 129 35256:25 00000000433a4bef [1,17,1] Recovered via rewrite in-place 130 35256:25 00000000433a4bf2 [1,17,3] Recovered via rewrite in-place 131 35256:25 00000000433a4bf6 [1,17,1] Recovered via rewrite in-place 132 35256:25 00000000433a4c09 [1,17,3] Recovered via rewrite in-place 133 35256:25 00000000433a4c0a [1,17,1] Recovered via rewrite in-place 134 35429:45 00000000433a4bed [1,17,1] Recovered via rewrite in-place 135 37564:35 000000001027f619 [1,17,1] Recovered via rewrite in-place 136 39765:22 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 137 40435:05 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 138 41927:37 000000001027f619 [1,17,1] Recovered via rewrite in-place 139 41972:09 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 140 42149:26 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 141 42191:53 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 142 42955:10 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 143 43738:54 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 144 43913:28 000000001027f619 [1,17,1] Recovered via rewrite in-place 145 44280:04 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 146 44325:55 000000001027f618 [1,17,1] Recovered via rewrite in-place 147 44397:40 000000003e62eb4c [1,17,1] Recovered via rewrite in-place 148 44745:56 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 149 44745:56 000000001027f619 [1,17,1] Recovered via rewrite in-place 150 45057:14 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 151 45493:20 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 152 45493:20 000000001027e9ea [1,17,1] Recovered via rewrite in-place 153 46105:56 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 154 46105:56 000000001027f619 [1,17,1] Recovered via rewrite in-place 155 46117:28 000000001027f618 [1,17,1] Recovered via rewrite in-place 156 46457:01 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 157 46627:21 000000003100a2b1 [1,17,1] Recovered via rewrite in-place 158 46627:21 000000003100a2b2 [1,17,1] Recovered via rewrite in-place 159 46627:21 000000003100a2b3 [1,17,1] Recovered via rewrite in-place 160 46643:52 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 161 46765:26 000000001027f619 [1,17,1] Recovered via rewrite in-place 162 46831:26 0000000032b7a8c4 [1,17,1] Recovered via rewrite in-place 163 46844:04 0000000030de8927 [1,17,1] Recovered via rewrite in-place 164 46985:55 000000003e62eb45 [1,17,1] Recovered via rewrite in-place 165 47109:47 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 166 47625:26 000000001027f619 [1,17,1] Recovered via rewrite in-place 167 47827:53 000000003100a26b [1,17,1] Recovered via rewrite in-place 168 47876:04 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 169 47876:04 000000001027f618 [1,17,1] Recovered via rewrite in-place 170 48504:07 000000001027f619 [1,17,1] Recovered via rewrite in-place 171 48534:42 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 172 48841:25 000000001027f618 [1,17,1] Recovered via rewrite in-place 173 49180:31 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 174 49180:31 000000001027f619 [1,17,1] Recovered via rewrite in-place 175 49215:58 000000003e5fe166 [1,17,1] Recovered via rewrite in-place 176 49554:38 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 177 49754:43 000000003e62eb46 [1,17,1] Recovered via rewrite in-place 178 49951:28 000000001027f619 [1,17,1] Recovered via rewrite in-place 179 49984:15 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 180 50184:03 000000001027f618 [1,17,1] Recovered via rewrite in-place 181 50220:34 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 182 50533:50 000000001027e9e9 [1,17,2] Recovered via rewrite in-place 183 50955:15 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 184 50977:04 0000000032a5f3f9 [1,17,1] Recovered via rewrite in-place 185 51176:45 00000000323d1d26 [1,17,1] Recovered via rewrite in-place 186 51295:49 0000000032b7a8c6 [1,17,1] Recovered via rewrite in-place 187 51295:49 0000000032b7a8c7 [1,17,1] Recovered via rewrite in-place 188 51418:08 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 189 51418:08 000000001027e9ea [1,17,1] Recovered via rewrite in-place 190 51418:08 000000001027f619 [1,17,1] Recovered via rewrite in-place 191 51528:50 0000000032a5f3f8 [1,17,1] Recovered via rewrite in-place 192 51583:07 0000000030de8929 [1,17,1] Recovered via rewrite in-place 193 51790:28 000000003e62eb47 [1,17,1] Recovered via rewrite in-place 194 52100:05 000000001027f618 [1,17,1] Recovered via rewrite in-place 195 52435:03 0000000032a5f3f7 [1,17,1] Recovered via rewrite in-place 196 52619:52 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 197 52619:52 000000001027f619 [1,17,1] Recovered via rewrite in-place 198 52650:00 0000000032b7a8c4 [1,17,1] Recovered via rewrite in-place 199 53722:34 000000001027f618 [1,17,1] Recovered via rewrite in-place 200 53722:34 000000001027f619 [1,17,1] Recovered via rewrite in-place 201 53985:27 0000000030de892c [1,17,1] Recovered via rewrite in-place 202 54544:38 0000000030de8928 [1,17,1] Recovered via rewrite in-place 203 54602:41 0000000032b7a8cb [1,17,1] Recovered via rewrite in-place 204 54602:41 0000000032b7a8cc [1,17,1] Recovered via rewrite in-place 205 54647:58 0000000032b7a8c3 [1,17,1] Recovered via rewrite in-place 206 54647:58 0000000032b7a8c9 [1,17,1] Recovered via rewrite in-place 207 54999:25 000000001027e9e9 [1,17,2] Recovered via rewrite in-place 208 54999:25 000000001027f619 [1,17,3] Recovered via rewrite in-place 209 55342:36 000000003100a25e [1,17,1] Recovered via rewrite in-place 210 55443:14 00000000323d1d2a [1,17,1] Recovered via rewrite in-place 211 55573:45 000000003322f481 [1,17,1] Recovered via rewrite in-place 212 55872:19 000000001027f619 [1,17,1] Recovered via rewrite in-place 213 56043:54 00000000323df046 [1,17,1] Recovered via rewrite in-place 214 56086:19 000000003322f482 [1,17,1] Recovered via rewrite in-place 215 56380:48 00000000323df045 [1,17,1] Recovered via rewrite in-place 216 56640:22 00000000323df041 [1,17,1] Recovered via rewrite in-place 217 56654:31 0000000030de8927 [1,17,1] Recovered via rewrite in-place 218 56654:31 0000000030de8928 [1,17,1] Recovered via rewrite in-place 219 56654:31 0000000030de892a [1,17,1] Recovered via rewrite in-place 220 56749:44 000000001027e9e9 [1,17,2] Recovered via rewrite in-place 221 56749:44 000000001027f618 [1,17,1] Recovered via rewrite in-place 222 56749:44 000000001027f619 [1,17,1] Recovered via rewrite in-place 223 63262:13 00000000000254c9 [1,17,1] Recovered via rewrite in-place 224 63492:59 00000000087d781e [1,17,1] Recovered via rewrite in-place 225 63492:59 00000000087d781f [1,17,1] Recovered via rewrite in-place 226 63522:54 00000000000254c8 [1,17,1] Recovered via rewrite in-place 227 63649:31 00000000000254ca [1,17,1] Recovered via rewrite in-place 228 63655:33 0000000018ab5ae9 [1,17,1] Recovered via rewrite in-place 229 64158:40 00000000042ab1a8 [1,17,1] Recovered via rewrite in-place 230 64490:31 00000000087afb75 [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c5003b8d8eed attached SAS address = 0x500056b3b2546dff attached phy identifier = 6 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 1.5 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5003b8d8eee attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sdc,megaraid_disk_07 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST31000528AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC38 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:14 2024 +05 ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213891en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. Warning: This result is based on an Attribute check. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 173) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 099 006 - 65687095 3 Spin_Up_Time PO---- 094 092 000 - 0 4 Start_Stop_Count -O--CK 091 091 020 - 9726 5 Reallocated_Sector_Ct PO--CK 002 002 036 NOW 4015 7 Seek_Error_Rate POSR-- 061 060 030 - 1318954260943 9 Power_On_Hours -O--CK 071 071 000 - 25717 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4520 183 Runtime_Bad_Block -O--CK 082 082 000 - 18 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 091 000 - 107375886407 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 078 051 045 - 22 (Min/Max 21/23) 194 Temperature_Celsius -O---K 022 049 000 - 22 (255 254 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 018 016 000 - 65687095 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 36303 (47 34 0) 241 Total_LBAs_Written ------ 100 253 000 - 3743902899 242 Total_LBAs_Read ------ 100 253 000 - 4234266849 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 21/23 Celsius Lifetime Min/Max Temperature: -2/49 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc,megaraid_disk_08 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 (CMR) Device Model: ST1000DM010-2EP102 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC43 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:14 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 108) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 063 006 - 1176836 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 65 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 084 060 045 - 248750298 9 Power_On_Hours -O--CK 082 082 000 - 15934 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 58 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 081 054 040 - 19 (Min/Max 16/21) 193 Load_Cycle_Count -O--CK 100 100 000 - 709 194 Temperature_Celsius -O---K 019 015 000 - 19 (0 15 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 100 001 000 - 1176836 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 15856h+04m+51.422s 241 Total_LBAs_Written ------ 100 253 000 - 13847177004 242 Total_LBAs_Read ------ 100 253 000 - 9110076841 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4120 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 4800 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 17 Celsius Power Cycle Min/Max Temperature: 16/21 Celsius Lifetime Min/Max Temperature: 15/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 58 --- Lifetime Power-On Resets 0x01 0x010 4 15934 --- Power-on Hours 0x01 0x018 6 13847574178 --- Logical Sectors Written 0x01 0x020 6 386140105 --- Number of Write Commands 0x01 0x028 6 9116981665 --- Logical Sectors Read 0x01 0x030 6 171180761 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 9028 --- Spindle Motor Power-on Hours 0x03 0x010 4 370 --- Head Flying Hours 0x03 0x018 4 709 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 17 --- Current Temperature 0x05 0x010 1 18 --- Average Short Term Temperature 0x05 0x018 1 17 --- Average Long Term Temperature 0x05 0x020 1 47 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 45 --- Highest Average Short Term Temperature 0x05 0x038 1 17 --- Lowest Average Short Term Temperature 0x05 0x040 1 42 --- Highest Average Long Term Temperature 0x05 0x048 1 17 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 13 --- Specified Minimum Operating Temperature |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc,megaraid_disk_09 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Re Device Model: WDC WD2000FYYZ-01UL1B2 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01K03 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:14 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (25620) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 279) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 206 171 021 - 4675 4 Start_Stop_Count -O--CK 100 100 000 - 50 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 040 040 000 - 44275 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 50 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 48 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 128 110 000 - 22 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 35437 hours (1476 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 e4 6a 7d 40 00 Error: UNC at LBA = 0x00e46a7d = 14969469 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 02 00 00 08 00 00 00 e4 6a 00 40 00 21:45:17.467 READ FPDMA QUEUED 60 02 00 00 00 00 00 00 e4 68 00 40 00 21:45:17.464 READ FPDMA QUEUED 60 02 00 00 f8 00 00 00 e4 66 00 40 00 21:45:17.460 READ FPDMA QUEUED 60 02 00 00 f0 00 00 00 e4 64 00 40 00 21:45:17.454 READ FPDMA QUEUED 60 02 00 00 e8 00 00 00 e4 62 00 40 00 21:45:17.451 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 31939 hours (1330 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 e4 6a 73 40 00 Error: UNC at LBA = 0x00e46a73 = 14969459 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 02 00 00 f0 00 00 00 e4 6a 00 40 00 4d+06:21:35.535 READ FPDMA QUEUED 60 02 00 00 e8 00 00 00 e4 68 00 40 00 4d+06:21:35.531 READ FPDMA QUEUED 60 02 00 00 e0 00 00 00 e4 66 00 40 00 4d+06:21:35.528 READ FPDMA QUEUED 60 02 00 00 d8 00 00 00 e4 64 00 40 00 4d+06:21:35.522 READ FPDMA QUEUED 60 02 00 00 d0 00 00 00 e4 62 00 40 00 4d+06:21:35.518 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 20/23 Celsius Lifetime Min/Max Temperature: 9/40 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 225176 Vendor specific /dev/sdc,megaraid_disk_10 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Re Device Model: WDC WD2000FYYZ-01UL1B2 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01K03 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:14 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (25920) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 282) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 188 170 021 - 5558 4 Start_Stop_Count -O--CK 100 100 000 - 59 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 040 040 000 - 44467 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 59 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 57 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 128 106 000 - 22 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 19/23 Celsius Lifetime Min/Max Temperature: 10/44 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 225222 Vendor specific /dev/sdc,megaraid_disk_12 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Kingston SSDNow UV400/500 Device Model: KINGSTON SUV400S37240G Serial Number: -- LU WWN Device Id: 0 550380 ... Firmware Version: 0C3G37R5 User Capacity: 240,057,409,536 bytes [240 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5319 ATA Version is: ACS-4, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:14 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 5) minutes. Conveyance self-test routine recommended polling time: ( 0) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 48 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 105000293 5 Reallocated_Sector_Ct PO--CK 096 096 010 - 37 9 Power_On_Hours -O--CK 100 100 000 - 37542 12 Power_Cycle_Count -O--CK 100 100 000 - 8864 100 Unknown_Kingston_Attr -O--CK 100 100 000 - 180328640 101 Unknown_Kingston_Attr -O--CK 100 100 000 - 3533024 170 Reserved_Block_Count -O--CK 100 100 000 - 37 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 43 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 000 - 0 177 Wear_Leveling_Count -O--CK 134 000 000 - 79932 178 Used_Rsvd_Blk_Cnt_Chip -O---- 100 100 000 - 6 180 Unused_Rsvd_Blk_Cnt_Tot -O---- 100 100 000 - 770 183 Runtime_Bad_Block -O--CK 074 074 000 - 120 187 Reported_Uncorrect PO--CK 100 100 000 - 23978 194 Temperature_Celsius -O---K 027 100 000 - 27 (Min/Max 16/50) 195 Hardware_ECC_Recovered -O--CK 100 100 000 - 105000293 196 Reallocated_Event_Count -O--CK 100 100 000 - 37 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--C- 100 100 000 - 0 201 Unc_Read_Error_Rate -O--CK 100 100 000 - 0 204 Soft_ECC_Correction -O--CK 100 100 000 - 104976315 231 SSD_Life_Left -O--CK 000 000 000 - 100 233 Media_Wearout_Indicator -O--CK 100 100 000 - 462076 234 Unknown_Attribute -O--CK 100 100 000 - 31029 241 Host_Writes_GiB -O--CK 100 100 000 - 57742 242 Host_Reads_GiB -O--CK 100 100 000 - 90408 250 Read_Retry_Count -O--CK 100 100 000 - 716606443 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 5 Device Statistics Notification 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 9 Device vendor specific log 0xab SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 0 (1 sectors) Device Error Count: 1258 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1258 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 01 71 b3 fb e1 08 Error: UNC 5 sectors at LBA = 0x0171b3fb = 24228859 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 05 00 00 01 71 b3 fb e1 08 00:07:13.434 READ DMA Error 1257 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 71 b3 fa e1 08 Error: UNC 1 sectors at LBA = 0x0171b3fa = 24228858 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 01 00 00 01 71 b3 fa e1 08 00:07:13.402 READ DMA Error 1256 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 01 71 b3 f8 e1 08 Error: UNC 2 sectors at LBA = 0x0171b3f8 = 24228856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 02 00 00 01 71 b3 f8 e1 08 00:07:13.370 READ DMA Error 1255 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 01 71 b3 fc e1 08 Error: UNC 4 sectors at LBA = 0x0171b3fc = 24228860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 04 00 00 01 71 b3 fc e1 08 00:07:13.338 READ DMA SMART Extended Self-test Log Version: 0 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 24/29 Celsius Lifetime Min/Max Temperature: 16/50 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 8864 --- Lifetime Power-On Resets 0x01 0x010 4 37542 --- Power-on Hours 0x01 0x018 6 121094098990 --- Logical Sectors Written 0x01 0x020 6 1698224350 --- Number of Write Commands 0x01 0x028 6 189600064841 --- Logical Sectors Read 0x01 0x030 6 1636624910 --- Number of Read Commands 0x01 0x038 6 135152947090 --- Date and Time TimeStamp 0x02 ===== = = === == Free-Fall Statistics (empty) == 0x03 ===== = = === == Rotating Media Statistics (empty) == 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 23978 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 679 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 28 -D- Current Temperature 0x05 0x010 1 - -D- Average Short Term Temperature 0x05 0x018 1 0 -D- Average Long Term Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 27 -D- Highest Average Short Term Temperature 0x05 0x038 1 23 -D- Lowest Average Short Term Temperature 0x05 0x040 1 - -D- Highest Average Long Term Temperature 0x05 0x048 1 - -D- Lowest Average Long Term Temperature 0x05 0x050 4 0 -D- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 -D- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 679 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 100 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET /dev/sdc,megaraid_disk_13 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7E (AF) Device Model: SAMSUNG HM321HI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AJ10001 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:14 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. Warning: This result is based on an Attribute check. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 137) The previous self-test completed having a test element that failed and the device is suspected of having handling damage. Total time to complete Offline data collection: ( 4920) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 82) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 001 001 051 NOW 37634 2 Throughput_Performance POS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 093 091 025 - 2137 4 Start_Stop_Count -O--CK 095 095 000 - 5162 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-K 252 252 051 - 0 8 Seek_Time_Performance P-S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 19675 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 098 098 000 - 2748 12 Power_Cycle_Count -O--CK 095 095 000 - 5431 183 Runtime_Bad_Block -O--CK 252 252 010 - 0 184 End-to-End_Error PO--CK 252 252 048 - 0 186 Unknown_Attribute -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 37436 188 Command_Timeout -O--CK 252 252 000 - 0 190 Airflow_Temperature_Cel -O---- 077 043 040 - 23 (Min/Max 11/60) 191 G-Sense_Error_Rate -O---K 098 098 000 - 29220 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 193 Load_Cycle_Count -O--CK 064 064 000 - 366185 194 Temperature_Celsius -O---- 064 043 000 - 23 (Min/Max 11/60) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 2 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 1 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 9755 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 37437 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 37437 [4] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 10 00 08 00 00 0c b2 3e f0 40 08 00:00:14.989 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.989 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.989 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.989 SET FEATURES [Set transfer mode] Error 37436 [3] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 10 00 08 00 00 0c b2 3e f0 40 08 00:00:14.986 READ FPDMA QUEUED 61 00 10 00 30 00 00 03 49 52 f6 40 08 00:00:14.986 WRITE FPDMA QUEUED 61 00 10 00 58 00 00 03 49 52 96 40 08 00:00:14.986 WRITE FPDMA QUEUED 61 00 10 00 50 00 00 03 49 52 3e 40 08 00:00:14.986 WRITE FPDMA QUEUED Error 37435 [2] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 10 00 08 00 00 0c b2 3e f0 40 08 00:00:14.984 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.984 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.984 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.984 SET FEATURES [Set transfer mode] Error 37434 [1] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.982 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:14.978 FLUSH CACHE EXT 61 00 00 00 08 00 00 02 4d ea e6 40 08 00:00:14.978 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:14.978 FLUSH CACHE EXT Error 37433 [0] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.940 READ FPDMA QUEUED 60 00 10 00 08 00 00 05 64 a8 a8 40 08 00:00:14.953 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.953 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.953 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.953 SET FEATURES [Set transfer mode] Error 37432 [7] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.935 READ FPDMA QUEUED 60 00 10 00 08 00 00 05 64 a8 a8 40 08 00:00:14.951 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.951 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.951 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.951 SET FEATURES [Set transfer mode] Error 37431 [6] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.935 READ FPDMA QUEUED 60 00 10 00 08 00 00 05 64 a8 a8 40 08 00:00:14.948 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.948 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.948 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.948 SET FEATURES [Set transfer mode] Error 37430 [5] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.930 READ FPDMA QUEUED 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.946 READ FPDMA QUEUED 61 00 00 03 50 00 00 04 0d fa f6 40 08 00:00:14.946 WRITE FPDMA QUEUED 61 00 00 05 c8 00 00 04 0d f5 2e 40 08 00:00:14.946 WRITE FPDMA QUEUED 61 00 00 08 90 00 00 04 0d ec 9e 40 08 00:00:14.946 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: handling damage?? 90% 13782 0 # 2 Short offline Completed: handling damage?? 90% 13781 0 # 3 Short offline Completed: handling damage?? 90% 13780 0 SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed_handling_damage?? [90% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 22/24 Celsius Lifetime Min/Max Temperature: 16/63 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sde,megaraid_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital RE3 Serial ATA Device Model: WD2502ABYS-23B7A0 39M4511 42C0463IBM Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.03B07 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:15 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4680) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 58) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 200 199 021 - 975 4 Start_Stop_Count -O--CK 100 100 000 - 115 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 005 005 000 - 70011 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 114 192 Power-Off_Retract_Count -O--CK 200 200 000 - 112 193 Load_Cycle_Count -O--CK 200 200 000 - 2 194 Temperature_Celsius -O---K 123 103 000 - 20 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 20 Celsius Power Cycle Min/Max Temperature: 17/22 Celsius Lifetime Min/Max Temperature: 19/40 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x8000 4 225230 Vendor specific /dev/sde,megaraid_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital RE3 Serial ATA Device Model: WD2502ABYS-23B7A0 39M4511 42C0463IBM Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 02.03B07 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:16 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4680) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 58) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 200 199 021 - 991 4 Start_Stop_Count -O--CK 100 100 000 - 73 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 020 020 000 - 58642 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 72 192 Power-Off_Retract_Count -O--CK 200 200 000 - 57 193 Load_Cycle_Count -O--CK 200 200 000 - 15 194 Temperature_Celsius -O---K 124 101 000 - 19 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 36656 hours (1527 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 13 34 00 f0 00 40 00 Error: IDNF at LBA = 0x133400f000 = 82476855296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 05 00 00 b0 00 00 13 f0 34 00 40 08 00:11:51.129 WRITE FPDMA QUEUED 61 04 80 00 a8 00 00 13 f0 2f 80 40 08 00:11:51.121 WRITE FPDMA QUEUED 61 02 80 00 a0 00 00 13 f0 2d 00 40 08 00:11:51.115 WRITE FPDMA QUEUED 61 08 80 00 98 00 00 13 f0 24 80 40 08 00:11:51.110 WRITE FPDMA QUEUED 61 05 00 00 90 00 00 13 f0 1f 80 40 08 00:11:51.098 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 17 Celsius Power Cycle Min/Max Temperature: 16/21 Celsius Lifetime Min/Max Temperature: 17/42 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x8000 4 225230 Vendor specific /dev/sde,megaraid_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: MG04ACA200N 00YK039D7A01888LEN Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: TK44 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:16 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 232) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 3283 4 Start_Stop_Count -O--CK 100 100 000 - 206 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 083 083 000 - 7124 10 Spin_Retry_Count PO--CK 104 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 206 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 001 - 0 190 Airflow_Temperature_Cel -O---K 081 061 045 - 19 (Min/Max 17/20) 192 Power-Off_Retract_Count -O--CK 100 100 000 - 203 193 Load_Cycle_Count -O--CK 100 100 000 - 206 194 Temperature_Celsius -O---K 100 100 000 - 19 (Min/Max 15/39) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 253 000 - 0 212 Unknown_Attribute -O--CK 100 100 000 - 0 220 Disk_Shift -O---- 100 100 000 - 0 222 Loaded_Hours -O--CK 083 083 000 - 7121 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 546 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 12288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa7 GPL VS 8 Device vendor specific log 0xa8 GPL VS 7681 Device vendor specific log 0xb0 GPL,SL VS 1 Device vendor specific log 0xb1 GPL VS 12288 Device vendor specific log 0xdf GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 19 Celsius Power Cycle Min/Max Temperature: 17/20 Celsius Lifetime Min/Max Temperature: 15/39 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 206 --- Lifetime Power-On Resets 0x01 0x010 4 7124 --- Power-on Hours 0x01 0x018 6 307803767 --- Logical Sectors Written 0x01 0x020 6 986203 --- Number of Write Commands 0x01 0x028 6 27330642361 --- Logical Sectors Read 0x01 0x030 6 213541306 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 0 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 7121 --- Spindle Motor Power-on Hours 0x03 0x010 4 7121 --- Head Flying Hours 0x03 0x018 4 206 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 19 --- Current Temperature 0x05 0x010 1 18 N-- Average Short Term Temperature 0x05 0x018 1 16 N-- Average Long Term Temperature 0x05 0x020 1 39 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x030 1 27 N-- Highest Average Short Term Temperature 0x05 0x038 1 15 N-- Lowest Average Short Term Temperature 0x05 0x040 1 22 N-- Highest Average Long Term Temperature 0x05 0x048 1 16 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 44896 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sde,megaraid_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Purple Device Model: WDC WD40PURX-64GVNY0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:17 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (51840) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 518) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 171 171 021 - 8450 4 Start_Stop_Count -O--CK 100 100 000 - 318 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 077 077 000 - 17240 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 79 192 Power-Off_Retract_Count -O--CK 200 200 000 - 61 193 Load_Cycle_Count -O--CK 200 200 000 - 355 194 Temperature_Celsius -O---K 133 105 000 - 19 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 39 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] occurred at disk power-on lifetime: 6041 hours (251 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 01 aa ad fc c0 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 00 3d+04:19:17.645 FLUSH CACHE EXT 61 00 08 00 50 00 00 00 5c 64 70 40 00 3d+03:59:18.124 WRITE FPDMA QUEUED 61 00 08 00 48 00 00 00 5c 64 80 40 00 3d+03:59:18.123 WRITE FPDMA QUEUED 61 00 08 00 40 00 00 00 64 75 58 40 00 3d+03:59:13.028 WRITE FPDMA QUEUED 61 00 08 00 38 00 00 00 5c 64 78 40 00 3d+03:59:07.834 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 19 Celsius Power Cycle Min/Max Temperature: 17/20 Celsius Lifetime Min/Max Temperature: 16/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 225247 Vendor specific /dev/sde,megaraid_disk_06 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST3600057SS Revision: 0008 Compliance: SPC-3 User Capacity: 600,127,266,816 bytes [600 GB] Logical block size: 512 bytes Rotation Rate: 15000 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c5003b8d8eef Serial number: -- Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Thu Dec 5 12:18:17 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Current Drive Temperature: 28 C Drive Trip Temperature: 68 C Elements in grown defect list: 668 Vendor (Seagate Cache) information Blocks sent to initiator = 1438821285 Blocks received from initiator = 4292434641 Blocks read from cache and sent to initiator = 2949839783 Number of read and write commands whose size <= segment size = 2302975697 Number of read and write commands whose size > segment size = 0 Vendor (Seagate/Hitachi) factory information number of hours powered up = 65023.22 number of minutes until next internal SMART test = 25 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 1168962932 168 0 1168963100 1168963378 145872.211 278 write: 0 0 1 1 7 41996.684 1 verify: 137 0 0 137 144 0.000 3 Non-medium error count: 345 No Self-tests have been logged Background scan results log Status: waiting until BMS interval timer expires Accumulated power on time, hours:minutes 65023:13 [3901393 minutes] Number of background scans performed: 979, scan progress: 0.00% Number of background medium scans performed: 62171 # when lba(hex) [sk,asc,ascq] reassign_status 1 12968:43 0000000042e0b46c [1,18,1] Recovered via rewrite in-place 2 13000:52 0000000042e0b87e [3,11,0] Recovered via rewrite in-place 3 13000:52 0000000042e0b87f [3,11,0] Recovered via rewrite in-place 4 13000:52 0000000042e0bc90 [3,11,0] Recovered via rewrite in-place 5 13000:52 0000000042e0bc91 [3,11,0] Recovered via rewrite in-place 6 13000:52 0000000042e0bc92 [3,11,0] Recovered via rewrite in-place 7 13000:52 0000000042e0c0a3 [3,11,0] Recovered via rewrite in-place 8 13000:52 0000000042e0c4b5 [3,11,0] Recovered via rewrite in-place 9 13000:53 00000000436604ac [3,11,0] Recovered via rewrite in-place 10 13000:55 0000000044373d96 [1,17,3] Recovered via rewrite in-place 11 13000:55 0000000044373d97 [3,11,0] Recovered via rewrite in-place 12 13000:55 0000000044373d98 [3,11,0] Recovered via rewrite in-place 13 13000:55 000000004450bbca [3,11,0] Recovered via rewrite in-place 14 29816:10 00000000000abfb1 [1,18,1] Successfully reassigned 15 31418:07 00000000000ad314 [1,18,1] Successfully reassigned 16 31418:08 00000000000bbcf3 [1,17,2] Recovered via rewrite in-place 17 31513:53 00000000000accae [1,17,2] Successfully reassigned 18 31537:53 00000000000bb718 [1,17,3] Successfully reassigned 19 32304:11 00000000000af856 [1,17,3] Successfully reassigned 20 32661:48 000000003100a258 [1,17,1] Recovered via rewrite in-place 21 33056:00 00000000000ac1f5 [1,17,3] Successfully reassigned 22 33056:01 00000000000ae079 [3,11,0] Recovered via rewrite in-place 23 33056:02 00000000000ae07b [3,11,0] Successfully reassigned 24 33056:02 00000000000ae07d [3,11,0] Successfully reassigned 25 33056:02 00000000000ae07f [3,11,0] Successfully reassigned 26 33056:03 00000000000ae080 [3,11,0] Successfully reassigned 27 33056:03 00000000000ae081 [3,11,0] Successfully reassigned 28 33056:04 00000000000ae082 [3,11,0] Successfully reassigned 29 33056:04 00000000000ae09c [3,11,0] Successfully reassigned 30 33056:04 00000000000ae0ba [3,11,0] Successfully reassigned 31 33056:04 00000000000ae0bc [3,11,0] Successfully reassigned 32 33056:04 00000000000ae0be [3,11,0] Successfully reassigned 33 33056:05 00000000000ae0c1 [3,11,0] Successfully reassigned 34 33056:05 00000000000ae0c3 [3,11,0] Successfully reassigned 35 33056:05 00000000000ae0c5 [3,11,0] Successfully reassigned 36 33056:05 00000000000ae0c7 [3,11,0] Successfully reassigned 37 33056:05 00000000000ae0c9 [3,11,0] Successfully reassigned 38 33056:06 00000000000ae0cb [3,11,0] Successfully reassigned 39 33056:06 00000000000ae0cc [3,11,0] Successfully reassigned 40 33056:07 00000000000ae0ce [3,11,0] Successfully reassigned 41 33056:08 00000000000ae0d0 [3,11,0] Successfully reassigned 42 33056:10 00000000000ae0d6 [3,11,0] Successfully reassigned 43 33056:10 00000000000ae0d8 [1,17,2] Recovered via rewrite in-place 44 33056:10 00000000000ae0d9 [3,11,0] Successfully reassigned 45 33056:10 00000000000ae0db [3,11,0] Successfully reassigned 46 33056:10 00000000000ae0dd [3,11,0] Successfully reassigned 47 33056:10 00000000000ae0df [3,11,0] Successfully reassigned 48 33056:10 00000000000ae0e1 [3,11,0] Successfully reassigned 49 33056:11 00000000000ae0e3 [3,11,0] Successfully reassigned 50 33056:11 00000000000ae0e8 [3,11,0] Successfully reassigned 51 33056:11 00000000000ae0ec [3,11,0] Successfully reassigned 52 33056:13 00000000000ae0ee [3,11,0] Successfully reassigned 53 33056:13 00000000000ae0f0 [3,11,0] Successfully reassigned 54 33056:14 00000000000ae0f2 [3,11,0] Successfully reassigned 55 33056:14 00000000000ae0f4 [3,11,0] Successfully reassigned 56 33056:14 00000000000ae0f6 [3,11,0] Successfully reassigned 57 33056:14 00000000000ae0f7 [3,11,0] Successfully reassigned 58 33056:14 00000000000ae0f9 [3,11,0] Successfully reassigned 59 33056:15 00000000000ae0fb [3,11,0] Successfully reassigned 60 33056:15 00000000000ae0fd [3,11,0] Successfully reassigned 61 33056:15 00000000000ae0ff [1,17,2] Recovered via rewrite in-place 62 33056:15 00000000000ae170 [1,17,1] Recovered via rewrite in-place 63 33056:15 00000000000ae172 [1,18,1] Recovered via rewrite in-place 64 33056:15 00000000000ae1e5 [1,18,1] Recovered via rewrite in-place 65 33056:15 00000000000ae1e7 [1,18,1] Recovered via rewrite in-place 66 33056:15 00000000000ae61d [3,11,0] Successfully reassigned 67 33056:15 00000000000ae61f [3,11,0] Successfully reassigned 68 33056:15 00000000000ae621 [3,11,0] Successfully reassigned 69 33056:16 00000000000ae623 [3,11,0] Successfully reassigned 70 33056:16 00000000000ae625 [3,11,0] Successfully reassigned 71 33056:16 00000000000ae628 [1,17,1] Recovered via rewrite in-place 72 33056:16 00000000000ae62a [1,18,1] Recovered via rewrite in-place 73 33056:16 00000000000ae62b [1,17,2] Recovered via rewrite in-place 74 33056:16 00000000000ae62c [3,11,0] Successfully reassigned 75 33056:16 00000000000ae62e [3,11,0] Successfully reassigned 76 33056:16 00000000000ae630 [3,11,0] Successfully reassigned 77 33056:16 00000000000ae632 [3,11,0] Successfully reassigned 78 33056:16 00000000000ae634 [3,11,0] Successfully reassigned 79 33056:16 00000000000ae636 [3,11,0] Successfully reassigned 80 33056:17 00000000000ae638 [3,11,0] Successfully reassigned 81 33056:17 00000000000ae63a [3,11,0] Successfully reassigned 82 33056:18 00000000000ae63c [3,11,0] Successfully reassigned 83 33056:20 00000000000ae645 [3,11,0] Successfully reassigned 84 33056:20 00000000000ae647 [3,11,0] Successfully reassigned 85 33056:21 00000000000ae649 [3,11,0] Successfully reassigned 86 33056:22 00000000000ae64b [1,17,2] Recovered via rewrite in-place 87 33056:23 00000000000b009b [3,11,0] Successfully reassigned 88 33056:23 00000000000b009d [3,11,0] Successfully reassigned 89 33056:23 00000000000b009f [3,11,0] Successfully reassigned 90 33056:23 00000000000b00ac [1,17,2] Recovered via rewrite in-place 91 33056:24 00000000000b00ae [3,11,0] Successfully reassigned 92 33056:24 00000000000b00b0 [3,11,0] Successfully reassigned 93 33056:24 00000000000b00bd [3,11,0] Successfully reassigned 94 33056:24 00000000000b00bf [3,11,0] Successfully reassigned 95 33056:24 00000000000b00c1 [3,11,0] Successfully reassigned 96 33056:25 00000000000b00c5 [3,11,0] Successfully reassigned 97 33056:25 00000000000b00c7 [3,11,0] Successfully reassigned 98 33056:25 00000000000b0760 [3,11,0] Successfully reassigned 99 33056:25 00000000000b0762 [3,11,0] Successfully reassigned 100 33056:25 00000000000b0764 [3,11,0] Successfully reassigned 101 33056:25 00000000000b0766 [3,11,0] Successfully reassigned 102 33056:25 00000000000b0768 [3,11,0] Successfully reassigned 103 33056:25 00000000000b0769 [3,11,0] Successfully reassigned 104 33056:26 00000000000b076b [3,11,0] Successfully reassigned 105 33056:26 00000000000b076d [3,11,0] Successfully reassigned 106 33056:26 00000000000b076f [3,11,0] Successfully reassigned 107 33056:26 00000000000b0771 [3,11,0] Successfully reassigned 108 33056:26 00000000000b0773 [3,11,0] Successfully reassigned 109 33056:26 00000000000b0775 [3,11,0] Successfully reassigned 110 33056:27 00000000000b8327 [3,11,0] Successfully reassigned 111 33056:28 00000000000b8328 [3,11,0] Successfully reassigned 112 33056:29 00000000000b832a [3,11,0] Successfully reassigned 113 33056:29 00000000000b832b [1,17,2] Recovered via rewrite in-place 114 33056:29 00000000000b832c [3,11,0] Successfully reassigned 115 33056:29 00000000000b832e [3,11,0] Successfully reassigned 116 33056:29 00000000000b8330 [3,11,0] Successfully reassigned 117 33056:30 00000000000b8332 [3,11,0] Successfully reassigned 118 33056:30 00000000000b90af [3,11,0] Successfully reassigned 119 33056:30 00000000000b90b8 [3,11,0] Successfully reassigned 120 33056:30 00000000000b9735 [1,17,1] Recovered via rewrite in-place 121 33095:58 0000000001b9afe2 [3,11,0] Successfully reassigned 122 33103:57 00000000000ae176 [1,17,2] Successfully reassigned 123 33127:53 00000000000ae59e [1,17,2] Recovered via rewrite in-place 124 33199:42 00000000000b9728 [1,17,2] Recovered via rewrite in-place 125 33391:19 00000000000ae086 [1,17,2] Recovered via rewrite in-place 126 33391:19 00000000000b00b7 [1,17,1] Successfully reassigned 127 33415:15 00000000000b972e [1,17,2] Successfully reassigned 128 35256:25 00000000433a4bee [1,17,1] Recovered via rewrite in-place 129 35256:25 00000000433a4bef [1,17,1] Recovered via rewrite in-place 130 35256:25 00000000433a4bf2 [1,17,3] Recovered via rewrite in-place 131 35256:25 00000000433a4bf6 [1,17,1] Recovered via rewrite in-place 132 35256:25 00000000433a4c09 [1,17,3] Recovered via rewrite in-place 133 35256:25 00000000433a4c0a [1,17,1] Recovered via rewrite in-place 134 35429:45 00000000433a4bed [1,17,1] Recovered via rewrite in-place 135 37564:35 000000001027f619 [1,17,1] Recovered via rewrite in-place 136 39765:22 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 137 40435:05 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 138 41927:37 000000001027f619 [1,17,1] Recovered via rewrite in-place 139 41972:09 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 140 42149:26 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 141 42191:53 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 142 42955:10 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 143 43738:54 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 144 43913:28 000000001027f619 [1,17,1] Recovered via rewrite in-place 145 44280:04 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 146 44325:55 000000001027f618 [1,17,1] Recovered via rewrite in-place 147 44397:40 000000003e62eb4c [1,17,1] Recovered via rewrite in-place 148 44745:56 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 149 44745:56 000000001027f619 [1,17,1] Recovered via rewrite in-place 150 45057:14 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 151 45493:20 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 152 45493:20 000000001027e9ea [1,17,1] Recovered via rewrite in-place 153 46105:56 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 154 46105:56 000000001027f619 [1,17,1] Recovered via rewrite in-place 155 46117:28 000000001027f618 [1,17,1] Recovered via rewrite in-place 156 46457:01 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 157 46627:21 000000003100a2b1 [1,17,1] Recovered via rewrite in-place 158 46627:21 000000003100a2b2 [1,17,1] Recovered via rewrite in-place 159 46627:21 000000003100a2b3 [1,17,1] Recovered via rewrite in-place 160 46643:52 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 161 46765:26 000000001027f619 [1,17,1] Recovered via rewrite in-place 162 46831:26 0000000032b7a8c4 [1,17,1] Recovered via rewrite in-place 163 46844:04 0000000030de8927 [1,17,1] Recovered via rewrite in-place 164 46985:55 000000003e62eb45 [1,17,1] Recovered via rewrite in-place 165 47109:47 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 166 47625:26 000000001027f619 [1,17,1] Recovered via rewrite in-place 167 47827:53 000000003100a26b [1,17,1] Recovered via rewrite in-place 168 47876:04 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 169 47876:04 000000001027f618 [1,17,1] Recovered via rewrite in-place 170 48504:07 000000001027f619 [1,17,1] Recovered via rewrite in-place 171 48534:42 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 172 48841:25 000000001027f618 [1,17,1] Recovered via rewrite in-place 173 49180:31 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 174 49180:31 000000001027f619 [1,17,1] Recovered via rewrite in-place 175 49215:58 000000003e5fe166 [1,17,1] Recovered via rewrite in-place 176 49554:38 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 177 49754:43 000000003e62eb46 [1,17,1] Recovered via rewrite in-place 178 49951:28 000000001027f619 [1,17,1] Recovered via rewrite in-place 179 49984:15 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 180 50184:03 000000001027f618 [1,17,1] Recovered via rewrite in-place 181 50220:34 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 182 50533:50 000000001027e9e9 [1,17,2] Recovered via rewrite in-place 183 50955:15 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 184 50977:04 0000000032a5f3f9 [1,17,1] Recovered via rewrite in-place 185 51176:45 00000000323d1d26 [1,17,1] Recovered via rewrite in-place 186 51295:49 0000000032b7a8c6 [1,17,1] Recovered via rewrite in-place 187 51295:49 0000000032b7a8c7 [1,17,1] Recovered via rewrite in-place 188 51418:08 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 189 51418:08 000000001027e9ea [1,17,1] Recovered via rewrite in-place 190 51418:08 000000001027f619 [1,17,1] Recovered via rewrite in-place 191 51528:50 0000000032a5f3f8 [1,17,1] Recovered via rewrite in-place 192 51583:07 0000000030de8929 [1,17,1] Recovered via rewrite in-place 193 51790:28 000000003e62eb47 [1,17,1] Recovered via rewrite in-place 194 52100:05 000000001027f618 [1,17,1] Recovered via rewrite in-place 195 52435:03 0000000032a5f3f7 [1,17,1] Recovered via rewrite in-place 196 52619:52 000000001027e9e9 [1,17,1] Recovered via rewrite in-place 197 52619:52 000000001027f619 [1,17,1] Recovered via rewrite in-place 198 52650:00 0000000032b7a8c4 [1,17,1] Recovered via rewrite in-place 199 53722:34 000000001027f618 [1,17,1] Recovered via rewrite in-place 200 53722:34 000000001027f619 [1,17,1] Recovered via rewrite in-place 201 53985:27 0000000030de892c [1,17,1] Recovered via rewrite in-place 202 54544:38 0000000030de8928 [1,17,1] Recovered via rewrite in-place 203 54602:41 0000000032b7a8cb [1,17,1] Recovered via rewrite in-place 204 54602:41 0000000032b7a8cc [1,17,1] Recovered via rewrite in-place 205 54647:58 0000000032b7a8c3 [1,17,1] Recovered via rewrite in-place 206 54647:58 0000000032b7a8c9 [1,17,1] Recovered via rewrite in-place 207 54999:25 000000001027e9e9 [1,17,2] Recovered via rewrite in-place 208 54999:25 000000001027f619 [1,17,3] Recovered via rewrite in-place 209 55342:36 000000003100a25e [1,17,1] Recovered via rewrite in-place 210 55443:14 00000000323d1d2a [1,17,1] Recovered via rewrite in-place 211 55573:45 000000003322f481 [1,17,1] Recovered via rewrite in-place 212 55872:19 000000001027f619 [1,17,1] Recovered via rewrite in-place 213 56043:54 00000000323df046 [1,17,1] Recovered via rewrite in-place 214 56086:19 000000003322f482 [1,17,1] Recovered via rewrite in-place 215 56380:48 00000000323df045 [1,17,1] Recovered via rewrite in-place 216 56640:22 00000000323df041 [1,17,1] Recovered via rewrite in-place 217 56654:31 0000000030de8927 [1,17,1] Recovered via rewrite in-place 218 56654:31 0000000030de8928 [1,17,1] Recovered via rewrite in-place 219 56654:31 0000000030de892a [1,17,1] Recovered via rewrite in-place 220 56749:44 000000001027e9e9 [1,17,2] Recovered via rewrite in-place 221 56749:44 000000001027f618 [1,17,1] Recovered via rewrite in-place 222 56749:44 000000001027f619 [1,17,1] Recovered via rewrite in-place 223 63262:13 00000000000254c9 [1,17,1] Recovered via rewrite in-place 224 63492:59 00000000087d781e [1,17,1] Recovered via rewrite in-place 225 63492:59 00000000087d781f [1,17,1] Recovered via rewrite in-place 226 63522:54 00000000000254c8 [1,17,1] Recovered via rewrite in-place 227 63649:31 00000000000254ca [1,17,1] Recovered via rewrite in-place 228 63655:33 0000000018ab5ae9 [1,17,1] Recovered via rewrite in-place 229 64158:40 00000000042ab1a8 [1,17,1] Recovered via rewrite in-place 230 64490:31 00000000087afb75 [1,17,1] Recovered via rewrite in-place Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: expander device attached reason: SMP phy control function reason: loss of dword synchronization negotiated logical link rate: phy enabled; 6 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=1 SAS address = 0x5000c5003b8d8eed attached SAS address = 0x500056b3b2546dff attached phy identifier = 6 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 1 Phy reset problem count = 0 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; 1.5 Gbps attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c5003b8d8eee attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sde,megaraid_disk_07 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST31000528AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC38 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:19 2024 +05 ==> WARNING: A firmware update for this drive may be available, see the following Seagate web pages: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/213891en SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. Warning: This result is based on an Attribute check. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 173) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 099 006 - 65687095 3 Spin_Up_Time PO---- 094 092 000 - 0 4 Start_Stop_Count -O--CK 091 091 020 - 9726 5 Reallocated_Sector_Ct PO--CK 002 002 036 NOW 4015 7 Seek_Error_Rate POSR-- 061 060 030 - 1318954260943 9 Power_On_Hours -O--CK 071 071 000 - 25717 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4520 183 Runtime_Bad_Block -O--CK 082 082 000 - 18 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 091 000 - 107375886407 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 078 051 045 - 22 (Min/Max 21/23) 194 Temperature_Celsius -O---K 022 049 000 - 22 (255 254 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 018 016 000 - 65687095 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 36303 (67 242 0) 241 Total_LBAs_Written ------ 100 253 000 - 3743902899 242 Total_LBAs_Read ------ 100 253 000 - 4234266849 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 21/23 Celsius Lifetime Min/Max Temperature: -2/49 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sde,megaraid_disk_08 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate BarraCuda 3.5 (CMR) Device Model: ST1000DM010-2EP102 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC43 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:19 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 108) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 063 006 - 1176836 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 65 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 084 060 045 - 248750298 9 Power_On_Hours -O--CK 082 082 000 - 15934 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 58 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 082 054 040 - 18 (Min/Max 16/21) 193 Load_Cycle_Count -O--CK 100 100 000 - 709 194 Temperature_Celsius -O---K 018 015 000 - 18 (0 15 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 100 001 000 - 1176836 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 15856h+04m+56.749s 241 Total_LBAs_Written ------ 100 253 000 - 13847177004 242 Total_LBAs_Read ------ 100 253 000 - 9110076841 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4120 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 4800 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 17 Celsius Power Cycle Min/Max Temperature: 16/21 Celsius Lifetime Min/Max Temperature: 15/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 58 --- Lifetime Power-On Resets 0x01 0x010 4 15934 --- Power-on Hours 0x01 0x018 6 13847574178 --- Logical Sectors Written 0x01 0x020 6 386140105 --- Number of Write Commands 0x01 0x028 6 9116981665 --- Logical Sectors Read 0x01 0x030 6 171180761 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 9028 --- Spindle Motor Power-on Hours 0x03 0x010 4 370 --- Head Flying Hours 0x03 0x018 4 709 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 17 --- Current Temperature 0x05 0x010 1 18 --- Average Short Term Temperature 0x05 0x018 1 17 --- Average Long Term Temperature 0x05 0x020 1 47 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 45 --- Highest Average Short Term Temperature 0x05 0x038 1 17 --- Lowest Average Short Term Temperature 0x05 0x040 1 42 --- Highest Average Long Term Temperature 0x05 0x048 1 17 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 13 --- Specified Minimum Operating Temperature |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sde,megaraid_disk_09 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Re Device Model: WDC WD2000FYYZ-01UL1B2 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01K03 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:19 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (25620) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 279) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 206 171 021 - 4675 4 Start_Stop_Count -O--CK 100 100 000 - 50 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 040 040 000 - 44275 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 50 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 48 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 128 110 000 - 22 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 35437 hours (1476 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 e4 6a 7d 40 00 Error: UNC at LBA = 0x00e46a7d = 14969469 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 02 00 00 08 00 00 00 e4 6a 00 40 00 21:45:17.467 READ FPDMA QUEUED 60 02 00 00 00 00 00 00 e4 68 00 40 00 21:45:17.464 READ FPDMA QUEUED 60 02 00 00 f8 00 00 00 e4 66 00 40 00 21:45:17.460 READ FPDMA QUEUED 60 02 00 00 f0 00 00 00 e4 64 00 40 00 21:45:17.454 READ FPDMA QUEUED 60 02 00 00 e8 00 00 00 e4 62 00 40 00 21:45:17.451 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 31939 hours (1330 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 e4 6a 73 40 00 Error: UNC at LBA = 0x00e46a73 = 14969459 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 02 00 00 f0 00 00 00 e4 6a 00 40 00 4d+06:21:35.535 READ FPDMA QUEUED 60 02 00 00 e8 00 00 00 e4 68 00 40 00 4d+06:21:35.531 READ FPDMA QUEUED 60 02 00 00 e0 00 00 00 e4 66 00 40 00 4d+06:21:35.528 READ FPDMA QUEUED 60 02 00 00 d8 00 00 00 e4 64 00 40 00 4d+06:21:35.522 READ FPDMA QUEUED 60 02 00 00 d0 00 00 00 e4 62 00 40 00 4d+06:21:35.518 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 20/23 Celsius Lifetime Min/Max Temperature: 9/40 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 225181 Vendor specific /dev/sde,megaraid_disk_10 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Re Device Model: WDC WD2000FYYZ-01UL1B2 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01K03 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:19 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (25920) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 282) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 188 170 021 - 5558 4 Start_Stop_Count -O--CK 100 100 000 - 59 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 040 040 000 - 44467 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 59 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 200 200 000 - 57 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 128 106 000 - 22 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 1 Current Device Internal Status Data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 19/23 Celsius Lifetime Min/Max Temperature: 10/44 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 225227 Vendor specific /dev/sde,megaraid_disk_12 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Kingston SSDNow UV400/500 Device Model: KINGSTON SUV400S37240G Serial Number: -- LU WWN Device Id: 0 550380 ... Firmware Version: 0C3G37R5 User Capacity: 240,057,409,536 bytes [240 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5319 ATA Version is: ACS-4, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 5 12:18:20 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Disabled ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 5) minutes. Conveyance self-test routine recommended polling time: ( 0) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 48 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 105000293 5 Reallocated_Sector_Ct PO--CK 096 096 010 - 37 9 Power_On_Hours -O--CK 100 100 000 - 37542 12 Power_Cycle_Count -O--CK 100 100 000 - 8864 100 Unknown_Kingston_Attr -O--CK 100 100 000 - 180328640 101 Unknown_Kingston_Attr -O--CK 100 100 000 - 3533024 170 Reserved_Block_Count -O--CK 100 100 000 - 37 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 43 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 000 - 0 177 Wear_Leveling_Count -O--CK 134 000 000 - 79932 178 Used_Rsvd_Blk_Cnt_Chip -O---- 100 100 000 - 6 180 Unused_Rsvd_Blk_Cnt_Tot -O---- 100 100 000 - 770 183 Runtime_Bad_Block -O--CK 074 074 000 - 120 187 Reported_Uncorrect PO--CK 100 100 000 - 23978 194 Temperature_Celsius -O---K 027 100 000 - 27 (Min/Max 16/50) 195 Hardware_ECC_Recovered -O--CK 100 100 000 - 105000293 196 Reallocated_Event_Count -O--CK 100 100 000 - 37 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--C- 100 100 000 - 0 201 Unc_Read_Error_Rate -O--CK 100 100 000 - 0 204 Soft_ECC_Correction -O--CK 100 100 000 - 104976315 231 SSD_Life_Left -O--CK 000 000 000 - 100 233 Media_Wearout_Indicator -O--CK 100 100 000 - 462076 234 Unknown_Attribute -O--CK 100 100 000 - 31029 241 Host_Writes_GiB -O--CK 100 100 000 - 57742 242 Host_Reads_GiB -O--CK 100 100 000 - 90408 250 Read_Retry_Count -O--CK 100 100 000 - 716606443 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0a GPL R/W 5 Device Statistics Notification 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 9 Device vendor specific log 0xab SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 0 (1 sectors) Device Error Count: 1258 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1258 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 05 00 00 01 71 b3 fb e1 08 Error: UNC 5 sectors at LBA = 0x0171b3fb = 24228859 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 05 00 00 01 71 b3 fb e1 08 00:07:13.434 READ DMA Error 1257 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 01 71 b3 fa e1 08 Error: UNC 1 sectors at LBA = 0x0171b3fa = 24228858 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 01 00 00 01 71 b3 fa e1 08 00:07:13.402 READ DMA Error 1256 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 02 00 00 01 71 b3 f8 e1 08 Error: UNC 2 sectors at LBA = 0x0171b3f8 = 24228856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 02 00 00 01 71 b3 f8 e1 08 00:07:13.370 READ DMA Error 1255 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 01 71 b3 fc e1 08 Error: UNC 4 sectors at LBA = 0x0171b3fc = 24228860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 04 00 00 01 71 b3 fc e1 08 00:07:13.338 READ DMA SMART Extended Self-test Log Version: 0 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 24/29 Celsius Lifetime Min/Max Temperature: 16/50 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 8864 --- Lifetime Power-On Resets 0x01 0x010 4 37542 --- Power-on Hours 0x01 0x018 6 121094098990 --- Logical Sectors Written 0x01 0x020 6 1698224350 --- Number of Write Commands 0x01 0x028 6 189600064841 --- Logical Sectors Read 0x01 0x030 6 1636624910 --- Number of Read Commands 0x01 0x038 6 135152952240 --- Date and Time TimeStamp 0x02 ===== = = === == Free-Fall Statistics (empty) == 0x03 ===== = = === == Rotating Media Statistics (empty) == 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 23978 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 679 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 28 -D- Current Temperature 0x05 0x010 1 - -D- Average Short Term Temperature 0x05 0x018 1 0 -D- Average Long Term Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 16 --- Lowest Temperature 0x05 0x030 1 27 -D- Highest Average Short Term Temperature 0x05 0x038 1 23 -D- Lowest Average Short Term Temperature 0x05 0x040 1 - -D- Highest Average Long Term Temperature 0x05 0x048 1 - -D- Lowest Average Long Term Temperature 0x05 0x050 4 0 -D- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 -D- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 679 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 100 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET /dev/sde,megaraid_disk_13 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.12-4-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7E (AF) Device Model: SAMSUNG HM321HI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AJ10001 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Dec 5 12:18:20 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. Warning: This result is based on an Attribute check. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 137) The previous self-test completed having a test element that failed and the device is suspected of having handling damage. Total time to complete Offline data collection: ( 4920) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 82) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 001 001 051 NOW 37634 2 Throughput_Performance POS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 093 091 025 - 2137 4 Start_Stop_Count -O--CK 095 095 000 - 5162 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate POSR-K 252 252 051 - 0 8 Seek_Time_Performance P-S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 19675 10 Spin_Retry_Count PO--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 098 098 000 - 2748 12 Power_Cycle_Count -O--CK 095 095 000 - 5431 183 Runtime_Bad_Block -O--CK 252 252 010 - 0 184 End-to-End_Error PO--CK 252 252 048 - 0 186 Unknown_Attribute -O--CK 252 252 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 37436 188 Command_Timeout -O--CK 252 252 000 - 0 190 Airflow_Temperature_Cel -O---- 077 043 040 - 23 (Min/Max 11/60) 191 G-Sense_Error_Rate -O---K 098 098 000 - 29220 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 193 Load_Cycle_Count -O--CK 064 064 000 - 366185 194 Temperature_Celsius -O---- 064 043 000 - 23 (Min/Max 11/60) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 2 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 1 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 9755 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 37437 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 37437 [4] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 10 00 08 00 00 0c b2 3e f0 40 08 00:00:14.989 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.989 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.989 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.989 SET FEATURES [Set transfer mode] Error 37436 [3] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 10 00 08 00 00 0c b2 3e f0 40 08 00:00:14.986 READ FPDMA QUEUED 61 00 10 00 30 00 00 03 49 52 f6 40 08 00:00:14.986 WRITE FPDMA QUEUED 61 00 10 00 58 00 00 03 49 52 96 40 08 00:00:14.986 WRITE FPDMA QUEUED 61 00 10 00 50 00 00 03 49 52 3e 40 08 00:00:14.986 WRITE FPDMA QUEUED Error 37435 [2] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 10 00 08 00 00 0c b2 3e f0 40 08 00:00:14.984 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.984 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.984 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.984 SET FEATURES [Set transfer mode] Error 37434 [1] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 0c b2 3e f7 40 00 Error: UNC at LBA = 0x0cb23ef7 = 213008119 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.946 READ FPDMA QUEUED 60 00 00 00 08 00 00 0c b2 3e f0 40 08 00:00:14.982 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:14.978 FLUSH CACHE EXT 61 00 00 00 08 00 00 02 4d ea e6 40 08 00:00:14.978 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:14.978 FLUSH CACHE EXT Error 37433 [0] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.940 READ FPDMA QUEUED 60 00 10 00 08 00 00 05 64 a8 a8 40 08 00:00:14.953 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.953 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.953 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.953 SET FEATURES [Set transfer mode] Error 37432 [7] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.935 READ FPDMA QUEUED 60 00 10 00 08 00 00 05 64 a8 a8 40 08 00:00:14.951 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.951 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.951 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.951 SET FEATURES [Set transfer mode] Error 37431 [6] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.935 READ FPDMA QUEUED 60 00 10 00 08 00 00 05 64 a8 a8 40 08 00:00:14.948 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:14.948 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:14.948 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:00:14.948 SET FEATURES [Set transfer mode] Error 37430 [5] occurred at disk power-on lifetime: 13785 hours (574 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 05 64 a8 ac 40 00 Error: UNC at LBA = 0x0564a8ac = 90482860 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.930 READ FPDMA QUEUED 60 00 00 00 08 00 00 05 64 a8 a8 40 08 00:00:14.946 READ FPDMA QUEUED 61 00 00 03 50 00 00 04 0d fa f6 40 08 00:00:14.946 WRITE FPDMA QUEUED 61 00 00 05 c8 00 00 04 0d f5 2e 40 08 00:00:14.946 WRITE FPDMA QUEUED 61 00 00 08 90 00 00 04 0d ec 9e 40 08 00:00:14.946 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: handling damage?? 90% 13782 0 # 2 Short offline Completed: handling damage?? 90% 13781 0 # 3 Short offline Completed: handling damage?? 90% 13780 0 SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed_handling_damage?? [90% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 24 Celsius Power Cycle Min/Max Temperature: 22/24 Celsius Lifetime Min/Max Temperature: 16/63 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific